- available in conventional (5W-20, 5W-30) and synthetic (0W-20) grades
- specially developed to offer the best corrosion protection and minimize engine wear
- in harsh temperature conditions, protects against cold starts
The Mitsubishi Genuine Full Synthetic 0W-20 oil is specifically designed to offer the highest level of protection against corrosion, lessen engine wear, fight the formation of sludge and other deposits, and enhance fuel efficiency. A wide variety of ambient temperatures are possible thanks to special additives, which also guard against cold starts during severe weather. The premium engine oils 5W-20 and 5W-30, which offer protection against a variety of weather situations, protection against low temperature starts, and improved fuel economy, are created using the best quality oils and cutting-edge additive systems.
For the correct replacement schedule for your Mitsubishi vehicle, please refer to your owner’s manual.
In This Article...
Can 5W-30 be used in place of 5W 20?
It is generally not advised to substitute 5w30 oil (or any other oil weight) for 5w20 oil because even a small viscosity change has the potential to harm your engine.
Can I substitute 10w40 for 5w30?
5W-30 oil is not used in your car. According to Kia literature, 10W-40 oil viscosity is advised for your car. You can use 5W-30 oil if the outside temperature is considerably below 32 degrees when you are driving the car, but you can also use 10W-40 if the outside temperature is below freezing. Requesting an engine oil/filter change will have the answering mechanic take care of this for you if you prefer that this maintenance be done by a qualified Mechanic sent directly to your location by YourMechanic. Do not hesitate to get in touch with YourMechanic again if you have any more queries or worries.
Can I use 5w40 for 5w30?
This essentially indicates that each oil is equally viscous at lower temperatures and will remain so at a temperature of 30C, but that 5w40 oil operates better at higher temperatures than 5w30 oil, being effective up to ambient temperatures of 50C as opposed to 30C.
In comparison to, say, 10w40 oils, 5w40 and 5w30 motor oils have winter viscosity grades of five, making them effective down to temperatures of -30C and more viscous at extremely low temperatures.
As a result, 5w40 oils are probably utilized in higher-performance engines that operate at higher temperatures and loads than usual, such as those used in vehicles driven in metropolitan environments, which frequently sit in traffic, or in vehicles traveling at very high speeds, for example.
5w30 oils are a fantastic option if your vehicle is not made to be driven at a high rate of speed or if you drive more cautiously and sustainably. These typically perform better for certain engine parts like oil pumps, can clean the engine better, and have longer lives because they operate at lower temperatures.
Mitsubishi uses oil, why?
Q. With 190,252 kilometres, my 2006 Mitsubishi Outlander is in good condition. I updated the catalytic converters in the past two years, and ever since, the automobile has been burning oil. After getting my oil changed recently, I drove 275 miles before the check engine light appeared. The engine was dry when I checked it. What might the issue be? What do you think of the newest Mitsubishi Outlander, by the way?
A. Your Mitsubishi burning oil is most likely to blame for the catalytic converter failure. Verifying that the positive crankcase ventilation (PCV) system is working properly would be the first and simplest check. Oil use may increase if the PCV system is not operating properly. High engine temperatures, worn piston rings, and harmed valve seals can also contribute to oil consumption. At this stage, I would have the engine given a thorough diagnostic examination by a repair facility. Additionally, compression testing and cylinder leak down should be performed. Regarding the most recent Outlander (2015 model), it’s a really good car with lots of great amenities and a fantastic guarantee, but as a whole, I feel like it lags behind the competition by a few years.
Can I use 10w30 for 5w30?
If you are currently using 10W30, you can safely switch to 5W30, according to the API motor oil guide (in car engines). When cold, 5W30 is thinner than 10W30. (You must adhere to the manufacturer’s instructions). However, going from cost-effective 10W30 to 5W30 is not always advised.
Will using the incorrect oil harm my engine?
Although the brand of motor oil you use is important, the viscosity grade is more important. There are different engine oil grades (5W-30, 15W-40, 10W-30, etc.), each of which is created for a particular type of engine.
Some viscosities are suitable for cold areas, while others work better in warmer environments. Your car’s engine can run as long as feasible with the proper engine oil. Use the suggested oil, whether conventional, synthetic, or of a different viscosity, for the engine’s greatest performance and protection.
Because of this, it’s always advisable to abide by the manufacturer’s instructions while topping off your oil because awful things always happen when these instructions are disregarded. You should abide by the instructions in your owner’s manual to avoid oil leaks, overheating, decreased fuel efficiency, and damaged engines. Below is further information on these symptoms in more detail.
Oil leaks
Since different synthetic engine oils will have different flow characteristics, using the incorrect engine oil can result in oil leaks. You may detect a leak under your car or where it is parked. Older cars from the 1960s and 1970s or those with high mileage utilize heavier oil to assist seal and safeguard the engine. Modern automobiles, on the other hand, are made to consume thinner oil.
Gaskets and seals may leak if synthetic oil is used in place of conventional oil in an older or vehicle with a greater mileage. It won’t offer the necessary lubrication and protection if it’s too thin. The mess that results from an oil leak must be immediately fixed.
Engine overheating
If you don’t use the proper oil for your engine, overheating could result. In addition to lubricating the engine’s components, engine oil also absorbs some of the heat generated by the engine to prevent any of the components from overheating.
Contrary to the manufacturer’s advice, using a heavier oil can reduce flow and impair the oil’s capacity to maintain thermal balance. The resistance and heat generated for the incorrect application increase with oil thickness.
Reduced fuel economy
After an oil change, your fuel economy may have decreased, which could be the result of using the incorrect oil. Utilizing engine oil that is excessively thick or has a greater viscosity than what is advised can impact a vehicle’s fuel economy.
The energy required to pump an oil with a high viscosity will increase fuel consumption. Your engine will have to burn more fuel in order to overcome the increased resistance on the moving parts. The efficiency of the engine should increase if the oil is switched to one that is a little bit thinner. Use the weight and kind that are suited for your vehicle.
Cause damage to engine life
The incorrect engine oil can harm an engine by improperly lubricating its parts. As a result, there will be metal-on-metal contact between the moving pieces. Soon after, friction develops, leading to engine component wear. Additionally, it might harm your engine’s pistons, oil pump, cylinder wall, bearings, and other parts. This will thus limit the engine’s life and almost probably result in an engine failure.
Better oil to use: 5W-20 or 5W-30?
You should take into account two things while selecting the ideal multigrade engine oil for your vehicle:
- The temperature that your automobile usually operates at (whether you drive in colder temperature or hotter climates)
- The recommended oil viscosity grade for your engine
Even though certain automobiles do provide some variation in engine oil choices, the majority have a suggested viscosity grade. This is due to the fact that engines are built to run on a particular oil viscosity, and changing that could have an impact on the performance of your engine.
Ideally, 5W 30 oil is ideal for drivers who frequent more extreme weather conditions. Compared to 5W-20 oil, it has a higher viscosity index and a wider operating temperature range. In both colder and hotter climes, 5W 30 oil will provide better protection.
For people who reside in colder climates with low temperatures, 5W-20 oil is recommended. It is suitable for light-duty applications and engines with moderate temperature ranges. In cooler conditions, 5W-20 oil offers good start-up performance.
Note: An oil with a high mileage rating may be required for older vehicles (5W-20 or 5W-30). In this instance, the high mileage oil provides the engine with superior friction and engine drag protection at high temperatures.