owners of other Mitsubishi cars, including
the Outlander, 3000GT, Lancer Evolution (“Evo”), and
Galant, Montero, Galant, Eclipse, Endeavor, ASX, Triton L200, and
These do-it-yourself methods can be useful for Raider as well.
These are the replacement bulb part numbers:
Low Beam Number 9006, High Beam Number
Front Turn Signal 9005
WY21W, 7440NA, 7440A, and Side Marker #
2827 (or WY5W).
Possibly a 10mm socket with
a flathead screwdriver and a 1/4″ drive ratchet to access
the turn signal and high beam bulbs.
Lower Beam
The bulb is placed near the assembly’s center, closer to the edge.
(To turn on the driver-side low beam light)
If you have a turbocharged Lancer model, you must remove the 10mm
bolt holding the relay box in position. For a turbo’s passenger side
simply remove the engine coolant reservoir from the model.)
Gently pull the housing by reaching behind it.
the electrical connector for the low beam bulb’s retaining clip.
Turn the old bulb a quarter turn in the other direction.
and remove it from the housing with a firm pull.
If
If the new bulb becomes filthy, clean it with a paper towel that has been wet.
using rubbing alcohol
Put the replacement # 9006 low beam bulb in the
housing and tighten it in place by turning it 1/4 turn clockwise.
to get to the passenger’s high beam bulb
You must take off the 10mm bolt holding the side of the car.
Filler hose for windshield wiper fluid is in place.
Turn the 10mm bolt counterclockwise to release it.
direction, pull the wiper fluid hose back, and then. Set aside the 10mm bolt.
in a secure area.
Rotate
before pulling, turn the old high beam bulb’s base 1/4 turn counterclockwise.
Straight from the housing, it.
Place the replacement 9005 bulb in the housing and
To secure it in place, turn it 1/4 turn counterclockwise.
Change the black
To secure the plastic dust cap, turn it 1/4 turn counterclockwise.
Bulb for the front turn signal is
positioned at the headlight housing’s inner border.
PTP New Responsive 728×90 Index begins with!webbot bot=”HTMLMarkup” and finishes with!webbot bot=”HTMLMarkup” with the i-checksum 22613.
Squeeze the
Remove each pop rivet by using a flathead screwdriver to center it.
the entire fastening.
To
To disconnect the air intake duct, pull out the two plastic Phillips screws.
screws’ heads.
The air intake conduit does not have to be disconnected.
if you are only changing the front turn signal bulb on the passenger side.
You ought to try to pry out these
replacing screws with more easily removed pop rivet fasteners
going forward.
Straightaway remove the old turn signal bulb from
replace # 7440Abulb by pushing it into the socket. Additionally, you may utilize the #
WY21W or the 7440NA bulb.
Push the plastic pop rivets back in.
To hold them in place, tighten the fastener’s middle portion.
Reach inside and quarter-turn the bulb socket.
Before removing it straight out of the housing, turn it counterclockwise.
If you took away the
Replace the 10mm bolt by rotating the windshield wiper fluid fill tube.
until it is snug, turn it clockwise.
Activate the light to check the new bulbs.
flashing the high beams, turning on the warning signals, and turning on the headlights.
How is a headlight taken off of a 2005 Mitsubishi Lancer?
Changing a Lancer headlight
- In order to prop open the hood, turn off your Lancer.
- The headlight’s wire harness should be disconnected from the back cover.
- Remove the headlight’s back cover by turning it, then set it aside.
- To remove the socket from the headlight assembly, turn it counterclockwise.