How To Jump Start A Kia Forte

How to Jumpstart a Kia Forte LX 2.0L 4 Cyl., Model Years 20172018

Access the battery to find out where it is.
Jump Points: Find the ground and the positive terminal.
Jumping Procedure: After properly connecting the jumper cables, jump.
Replace the lid, being sure to do so correctly.

In This Article...

How can a Kia be jumpstarted?

Jump-starting a Car

Place the car with the good battery in the parking space facing the other car, and make sure it is off.
Find the batteries by lifting the hoods of both devices.
Decide which terminals are positive and negative.
Connect the red clamp to the dead battery’s positive post.

What are the simplest procedures for jumping a car?

If you’re fortunate (and take good care of your automobile), it’s possible that you won’t need to jumpstart a car for many years. You’ll be glad you know how to do it if you ever need to jump start your own vehicle.

You can be stuck for hours if you don’t know how. Don’t allow this vital ability slip your mind.

Attach

Connect the red (+) clamp to the dead battery’s positive terminal. Next, connect the red (+) clamp to the functional battery’s positive terminal. Attach the black (-) clamp to the active battery’s negative terminal. Last but not least, fasten the leftover black (-) to a deceased car’s unpainted metal surface.

How is a Kia battery charged?

You can either use a battery charger, drive or idle for at least 20 minutes to charge the battery, or receive a jump start from another vehicle.

You will need jumper cables and a car whose battery is not dead in order to jump-start your vehicle.
Find a driver whose car’s battery is still good. Check to see if they have jumper cables. Find someone with jumper cables if they don’t.
Place a working vehicle with a booster battery next to the vehicle with a dead battery, being careful to keep the two vehicles apart.
Make that the booster battery is 12-volts and has the grounding wire attached to the negative terminal.
Unnecessary electrical loads should be turned off.
Remove the service cover from the engine compartment’s front passenger seat side by opening the engine hood.
The make and model of your car determines how easily you can access your battery. Some might even be hidden behind the seats or in the boot.
Take off the fuse box lid. Open the negative terminal cap near the car body and the positive terminal cap within the engine room fuse box.
Connect the positive end of the discharged battery to the red, positive clamped end of a jumper cable.
Connect the other end (red positive clamp) to the booster battery’s positive terminal.
The other jumper cable’s (black, negative clamp) other end should be connected to the negative terminal of the booster battery, and the other end should be connected to a stationary, solid metallic object far from the battery.
Start the engine of the working vehicle and let it run for a few seconds to start charging the dead vehicle’s battery with the jumper cables.
When the dead car starts, unplug the jumper wires in the opposite order (first the black, negative clamps, then the red, positive clamps), being careful to avoid touching the clamps.
To build up the charge, take a little drive or leave it idle for at least 20 minutes.

To charge your battery, adhere to the simple directions below:

Make sure you turn off the battery charger.
Connect the charger’s positive and negative cables to the appropriate ends of the battery.
Turn on the charger when it is charging at its slowest rate, and then set the timer. It should take 6 to 12 hours to fully charge, depending on the battery voltage and cold cranking amps (CCA).
After finishing, switch off the main battery charger.
Negative and positive clamps should be disconnected from the corresponding battery terminals in that order.

Tip #2:

When jumpstarting your car, be careful to adhere to the owner’s manual’s directions. Every automobile is unique. Believe us. We’re experts.

Attention: Under no circumstances should you attempt to connect any unsecured wires. Leave the dangerous stuff to us unless you are a trained technician. It’s incredibly simple to short out pricey computer components and put yourself in danger if the wiring is handled improperly.

To kickstart an automobile, where do you place the cables?

One of the cutting-edge and essential services that Urgently has found to help our partners’ EV strategies and improve the ownership experience for their consumers is mobile EV charging.

Your vehicle’s battery is a crucial component that performs one of the most crucial functions: starting the vehicle. The battery in the majority of conventional vehicle types, or gasoline-powered cars, is a SLI, or a starting, lighting, and ignition battery. Its primary function is to start the engine, although it can also be used to run the car’s lights and radio. The alternator in your car produces the majority of the energy required to power it once the engine is going. However, starting the car is a crucial function of the car battery; without it, the vehicle is essentially useless. A dead battery is likely to be the cause when you turn the key and hear some spitting, or perhaps nothing at all, but the engine won’t start.

Take some time to compile some information before attempting to jump start your car. Read the manual for your automobile, paying close attention to any sections on jump starters or car batteries. Some automakers may advise you against jumping starting the vehicle, while others may provide you with unique instructions tailored to your model. Ensure that you are aware of where your car’s battery is. The engine is often located in the front of the car, under the hood. However, the battery can be found in the trunk of some vehicles. If this is the situation, there are frequently specific terminals under the hood that can be used in the event of a jump start. Look at the battery to determine which terminals are positive and which are negative. A + (plus) sign for positive and a – (minus) sign for negative markings should be plainly visible on each terminal. Knowing which is which is essential since the batteries must be connected correctly for a successful jump start and to prevent a risky mishap.

One red and one black wire should be included in a set of jumper cables. Where to attach the cables is clearly shown by the colors. In any electrical system, electrical energy travels down a wire network from a battery’s negative terminal to its positive terminal, powering an object along the way, in this case the vehicle’s starter. One needs to make sure that the proper terminals are connected in order for a jump start to function properly. The side that should be connected to the positive terminal will always be represented by the red wire, and the side that should be connected to the negative terminal by the black cable. Don’t contact anything other than the intended target with the jumper cable clamps.

Using a portable jump starter or the assistance of another vehicle, you can jump start an automobile.

In either scenario, make sure all tools and vehicles are off before continuing. Remove all of your keys from the ignition for your own safety. Make sure there are no combustible materials nearby. Sparks, fires, and even explosions are conceivable while jump starting an automobile, albeit they are rare. High volts of electricity are present in car batteries and jump starter packs, and while jump starts and cables are made to minimize the risk of wrong use, accidents can still occur in certain situations.

If you need to jump start your car using the jumper wires from another vehicle, follow these instructions:

Find the location of each car’s battery first. The battery is usually located alongside the engine in cars. Then, position the vehicles near enough to one another so that you may attach jumper cables to the batteries of both vehicles. But watch out that nothing on either automobile touches anything else. This is necessary to stop any electrical current from traveling between the vehicles other than via the jumper wires. To start the process, both automobiles need to be put in park and turned off. Again, take note of the positive and negative terminals on each battery. After that, connect the jumper cables where necessary. The positive (red) cable needs to be connected to each battery’s positive terminals. The negative (black) cable needs to have one end grounded and the other end connected to the dead battery’s negative terminal.

The following is the safest way to attach the jumper cables:

One red jumper cable clamp should be attached to the dead battery’s positive terminal.
The positive terminal of the functioning (live) automobile battery should be connected to the opposite end of the same wire, the second red jumper cable clip.
One black jumper cable clamp should be attached to the negative terminal of the active (functioning) car’s battery.
On the vehicle with the dead battery, fasten the other end of that wirethe second black jumper cable clampto an unpainted piece of stationary metal. Don’t connect this clamp to the dead automobile battery’s negative terminal.

Though some might argue that it’s acceptable to secure the last negative jumper wire clamp to the dead battery’s negative terminal, doing so raises the possibility of a fire or explosion if the jump start doesn’t go as intended. To reduce the risk of sparks igniting any hydrogen gas that might be flowing from the battery, try to locate a location far from the battery. Better alternatives include the vehicle’s frame, an engine bolt, the bracket holding the alternator, or a specific grounding terminal that is not connected to the battery.

Start the vehicle with the live battery next. The dead battery will begin to recharge right away. The car with the dead battery may occasionally be able to be started right away, but other times it will require some time to charge. To allow electrical current to move from the functioning battery to the dead one, let the engine run for a few minutes. After that, try using the dead battery to start the vehicle. Start by turning the key and holding it there for no more than a few seconds. You might want to give this a few tries. If you were successful with your jump start, the engine should start right up. Depending on what caused your dead battery, you might want to get the automobile checked out right away. In other cases, your automobile can be fine following the jump start. A short drive will assist in recharging the battery.

The jumper cables must be cut off as the final step. It should be done in the opposite sequence from how they were connected. You run the risk of transmitting an electrical charge somewhere you may not want it if you touch the cords before they are entirely removed.

So, it’s advisable to do these steps in the following order:

On the vehicle that was given a jump start, disconnect the negative (black) jumper cable clamp from the chassis or terminal.
Negative (black) jumper cable clamp should be disconnected from the functional battery’s negative terminal.
Remove the positive (red) jumper cable clamp from the positive terminal of the working battery.
From the vehicle that received the jump start, disconnect the positive (red) jumper cable clamp.

Congratulationsyou just jump-started your car! Don’t forget to express your gratitude to the neighbor, friend, family member, or good samaritan that lent you their live battery to assist you out!

However, if your jump start doesn’t work and you find yourself repeatedly twisting the key in the ignition without the engine starting, you might be dealing with a bigger issue. In this situation, it is best to either have a mechanic inspect the vehicle or tow it to a repair facility.

If you’re using a portable jump starter to jump start your car, follow these instructions:

Portable battery packs, jump starters, and jump boxes are frequently small enough to be kept in your car’s glove box or trunk in case you need them. However, make sure to read the instructions carefully because not all of them can be stored in the hot, high temperatures that summertime cars can reach. The jump starter should be off when you start the process, just like when you jump start another automobile. You should also turn off your vehicle’s accessories.

Many portable chargers and jump starters have two clamps that are permanently attached to the device. One positive (red) and one negative (black) clamp should be present. To help prevent the likelihood of a spark, keep them apart. If the cables aren’t already attached, you’ll attach them to the portable jump starter while the car and jump starter are still off, making sure the positive (red) wire is linked to the positive terminal and the negative (black) cable is connected to the negative terminal.

Connect the clamp on the black jumper wire to either an unpainted metal item in the engine or straight to your car’s chassis, and the clamp on the red jumper cable to the positive terminal on your car battery (the frame of the vehicle). Don’t connect the negative (black) clamp to the dead battery’s negative terminal. In order to decrease the chance of sparking, which could start a fire or explosion, it is crucial to connect the cables in the correct order. It is also safer to connect the negative (black) clamp as far away from the battery as you can.

Turn on the jump starter once the cables are securely fastened. After then, try to start the car. Start the car by turning the key in the ignition and, if required, holding it there for a few seconds. Give the battery pack some time to cool down and readjust itself if a few seconds of trying to start the car doesn’t work. Your battery will receive more energy in an effort to start the car as a result of this.

If the jump start was effective, you should hear your engine start to turn over and run independently. Congratulations! The cords for the jump starter can now be unplugged. Remove the positive (red) cable from the battery terminal after removing the negative (black) cable from the vehicle. Depending on what caused your dead battery, you might want to get the automobile checked out right away. In other cases, your automobile can be fine following the jump start. A short drive will assist in recharging the battery.