Vehicles with variable valve timing typically have the problem code P0014 (VVT). This also applies to the Kia Optima. To increase the motor’s operational efficiency, VVT moves the camshaft at various RPMs and engine loads. P0014 indicates that the camshaft position is too advanced relative to the specifications for proper operation.
You can see a list of some common problems that lead to P0014 below. Do be aware that low oil pressure, filthy oil, or issues with oil pressure can all cause this code to be set. This is due to the hydraulic energy that drives the camshaft actuators.
In This Article...
Can low oil result in P0014?
Run a scan check to see whether P0014 is accompanied by any other fault codes, then use a scan tool to turn off the engine warning light.
Use the oil dipstick to check the condition and level of the motor oil. If the oil level is below the required level, top it off with fresh oil and test-drive the car to make sure the problem is fixed. And if it is outdated, soiled, or the incorrect viscosity type, replace it, install a new filter, and conduct a test cycle to ensure the issue has been resolved.
Remove the valve cover’s bolts and look for engine sludge. You will need to drop your engine and flush it if there is sludge buildup since there will be deposits obstructing the oil galleries.
Check the camshaft oil control valve exhaust bank 1 for proper operation if the engine is free of buildup. The camshaft oil control valve can be tested by being unbolted and then being tested with a wire jumper. Using a pair of fused wire jumpers, supply the solenoid with power and ground. [Let the power supply be off for no more than 2 seconds]
The valve may move in either direction and will make a clicking sound if it is operating properly. Change the valve and test drive the car to observe what happens if there is no click or movement.
If you’ve tried the aforementioned diagnostic procedures and the problem still exists, your engine may have internal problems. For a professional diagnosis and repair, consult a mechanic.
Q: Can P0014 be caused by low oil?
Yes. Low oil levels can result in the onboard computer registering fault code P0014 because VVT depends on oil and pressure to operate at its best. Oil levels are quite simple to check, however low oil levels are caused by system leaks. Nevertheless, it takes a significant or prolonged leak for the problems with low oil pressure to surface.
But the oil filter might be to blame. This occurs when a subpar aftermarket filter is installed, which could lower oil pressure.
Oil-based problems, however, might not impact VVT systems with regular maintenance unless there is a manufacturer’s defect.
Q: Can too much oil cause P0014?
The pressure inside the engine will rise if there is too much oil present, which can result in a number of problems like spark fouling and collapsed valve pipes.
If the oil flow is excessively high, the oil regions will become blocked and foamy, which will affect lubrication. For the engine to function sweetly and smoothly, the oil flow needs to be restrained.
Q: How much does it cost to fix code P0014?
The price of repairing the P0014 error code depends on a number of factors. Possible fixes include changing the oil, replacing the variable valve timing control solenoid/Oil control valve, or replacing the engine. The estimated repair price listed below includes both labor and part costs.
- $30 to $70 for an oil and oil filter change
- $250-350 for a variable valve control solenoid
- Replacement engines cost $20004000.
Q: Can I drive my car with a P0014 code?
Please refrain from driving around with P0014 registered concerns even though you can. Driving with it will result in poor engine performance, difficulty starting, unpredictable idling, stalling, and higher fuel consumption.
Again, if a subpar VVT control solenoid initiates the problem, it may result in the failure of other connected components.
Is P0014 the exhaust or the intake?
The variable valve timing (VVT) system in a car raises fuel economy and engine performance. The fuel-air mixture is controlled by regulating the opening and closing of the exhaust and intake valves.
Depending on the demand on the engine at any given time, this management enables more power, better fuel efficiency, or a balanced approach.
The exhaust camshaft in bank 1 position “B” is the subject of the P0014 OBD-II generic code, which is only relevant to automobiles with variable valve timing. This part is in charge of managing the valves that release carbon emissions from engines.
P0014’s seriousness?
Diagnosis: Your car’s ability to drive will be significantly impacted by this issue code. The most frequent issues include an increase in engine stalling, a rough idle, poor fuel economy, and noises coming from the engine.
How much does a code P0014 repair cost?
The overadvanced position B variable valve timing on your car’s exhaust camshaft may be an indication of problems with the engine management module (ECM)
The P0014 engine code denotes a problem with the timing of the engine’s variable valves, a crucial element that can, among other things, influence your car’s fuel efficiency.
How much will it cost to fix?
Engine code P0014 repairs can range in price from $75 to $150 per hour of labor, depending on your local mechanic’s fees. Depending on what the mechanic needs to fix, the total price will vary. among the possibilities are
Can an Oil Change Fix Code P0014?
An oil change may resolve the problem if the code is brought on by a faulty oil filter. An oil change may not solve the problem, though, if the code is caused by something else, such as a leak or a timing issue with the engine. The only option to resolve a code that is being caused by an issue with the engine is often to repair the engine.
Can You Drive a Car with P0014 Code?
You can operate your vehicle with the P0014 code, yes. But as quickly as feasible, we advise having the code examined and fixed by a specialist. The camshaft position sensor issue indicated by the code can have an impact on how well your car performs.
Driving while the camshaft position sensor is broken can lead to a variety of issues, such as low fuel efficiency, reduced engine power, or engine failure. It is best to have your car checked out by a professional if you have any worries about how it is performing.
What does Timing Over Advanced bank 1 mean for the intake of a camshaft?
What the P0011 Code Indicates A Camshaft Position Timing Over Advanced or System Performance Bank 1 is the meaning of the P0011 DTC. The code indicates that a discovered discrepancy between the target camshaft position angle and the actual camshaft position angle has been detected and cannot be corrected by the ECM/PCM.
What does Timing Over Advanced bank 1 mean for the exhaust camshaft position?
Camshaft Position BTiming Over-Advanced or System Performance is the meaning of the OBD code P0014 (Bank 1). It means that the computer in your car has discovered a discrepancy between the desired and actual camshaft position angles. The letter “B” in the error code designates the afflicted camshaft.
Where is bank 1 of the camshaft position sensor?
The CMP Sensor is positioned underneath the timing belt cover. The camshaft position sensor is located behind the valve cover on the right side of the engine compartment.
What is the price of a camshaft sensor replacement?
The cost to replace a camshaft position sensor ranges from $95 to $200. Parts alone cost between $25 and $100. The cost of labor will be between $70 and $100 for a competent replacement.
If you have a luxury vehicle or are having the replacement done at a nearby car dealership, be prepared to pay more. These expenses will also be increased by additional fees and taxes.
What causes timing to be too precise?
The most plausible reasons are as follows: Camshaft timing is incorrect. The solenoid that controls the valve is jammed open. The wiring in the valve control solenoid system is faulty or broken.