With the push of a button, users of INFINITI’s amazing HomeLink Transceiver can control anything from their garage door to their house or office lighting.
See the setup and programming instructions for your HomeLink garage door opener in the guide below, and enjoy all the benefits of owning a new INFINITI car or SUV in the Phoenix area!
The system’s memory gets cleared in this way. (Do this only once or your programming will be erased.) Holding the button down until the red indicator light flashes is necessary (about 20 seconds).
Check your car to determine where HomeLink might be located—it could be on the rearview mirror, visor, or front console. All three places must follow the instructions.
Select the HomeLink button you want to use to configure your garage door to open, then press it and hold your handheld transmitter at the same time.
It ought to start out gently blinking before starting to flash quickly (about 90 seconds). You can release the buttons once the light has stopped flashing.
The majority of openers produced after 1996 have this additional security feature, therefore you’ll need to climb a ladder and press the “smart” or “learn” button on the motor.
Instead of witnessing a light flash constantly after completing the next-to-last step above, you will see a light flash for just two seconds before solidly illuminating.
You just need to do the following to get past the code protection:
Your opener’s “smart” button must be depressed and then released. NOTE: You have 30 seconds to finish the following step. A second person assisting should make everything go more easily.
Obtain them For two seconds, firmly press and then release the HomeLink button that was previously preset in your automobile. Three times through this process.
Want more assistance setting up INFINITI HomeLink? If you come see us at INFINITI on Camelback, one of our helpful staff members will be pleased to assist you.
In This Article...
Owners of Infiniti, Begin Here
Trying to set up your Infiniti’s HomeLink? The steps you must take to quickly and easily train your HomeLink are explained in the video on the right side of the page. The most frequently required video will start playing immediately, however we have added manufacturer-specific movies below the main player for some garage door openers.
Not a fan of video? By selecting your vehicle’s model name from the list below, you may also get comprehensive instructions tailored to your particular model.
Choose your training films from the list below the main video for Infiniti owners who use a garage door opener made by Genie, Sommer, or who have an older model of HomeLink (model years 2008 and earlier).
How do I set up the Infiniti QX60’s garage door opener?
I recently purchased a used Infiniti QX60 house, and I never considered asking the dealer how to unlock my garage door. Can I program my Infiniti QX60 to work with the garage door?
In less than two minutes, find out if your auto insurance is being overcharged.
Yes, programming your Infiniti QX60’s garage door opener is as easy as connecting the remote and clearing the memory.
With two persons, it is simpler to setup your garage door opener because only one person needs to climb a ladder and operate the garage door motor. Take these actions:
- Locate the HomeLink buttons on the front console or the rearview mirror.
- Pressing and holding the two outside HomeLink buttons for roughly 20 seconds will clear the system memory. The flashing of the red indication lights will begin.
- Select the desired HomeLink button while holding the garage door remote control one to three inches away from the HomeLink buttons. Next, simultaneously push the HomeLink and transmitter buttons.
- Watch for the warning lights to start blinking and then stay on.
- You now have 30 seconds to depress the opener’s motor’s Smart button. To get there, you might need a ladder.
- Afterward, hold down the HomeLink button you just preset for two seconds before letting go. This should be done twice more.
Feeling triumphant, this is a wonderful moment to download the Jerry app to reduce the cost of your auto insurance. Jerry is the top-rated insurance super app in America, saving users more than $800 year on vehicle insurance.
Without a remote, how can I program my Infiniti garage door opener?
Without a remote control, it is impossible to program a garage door opener. But the buttons on your car’s garage door opener can be reset using your remote transmitter. Alternatively, you can operate the door without a remote by using an electronic keypad.
- Press the program and arrow buttons at the same time on keypads. Before choosing your own, restore the brand’s default code.
- Press the two “end buttons” on control boxes to erase prior settings. Then sync your car’s buttons using the remote control.
How can I program the garage door on my Infiniti QX50?
To program a device, place the handheld transmitter 1-3 inches away from the HomeLink(r) buttons. 3. Press and hold down the HomeLink(r) button you want to program and the hand-held transmitter button at the same time using both hands. RELEASE THESE BUTTONS ONLY AFTER STEP 4 IS COMPLETE.
How should my Clicker garage door opener be programmed?
Click the Smart/Learn button, then let go. Push the program button until the LED turns on. To program, choose a button. Make sure the LED stops blinking after each time you hit the button.
Why won’t my car’s garage door opener function?
If using the remote and wall-mounted panel approach fails to raise or lower your door, there might be an issue with the receiver board in your garage door opener or the control wiring for the system. Follow these procedures to quickly check the wiring on your garage door opener:
- Disconnect the two wires from the motor and unplug the opener.
- Reconnect the power to your device, then program all the remote controls and clean the memory.
- Reconnect the control wiring to the motor after another period of unplugging the device.
- Find the controllers that are installed on the wall and cut the wiring.
- To check your door’s operation, use the remote control for your garage door opener.
How can my Nissan be connected to my garage?
Keep your Nissan HomeLink(r) opener one to three inches away from your garage door opener. Press and hold the chosen HomeLink(r) button as well as the open button on the garage door transmitter at the same time, being sure not to release until the following action is finished.
Without a Learn button, how can a garage door opener be programmed?
programming keypads for garage doors Enter your selected Personal Identification Number (PIN) using the keypad, then hit the “Enter” button as soon as it glows or flashes on the controller or keypad. To check whether the garage door opener is functioning properly, try the keypad PIN.
The HomeLink transmit button is not visible.
Your HomeLink buttons are normally found in the overhead console, center stack, or mirror of your car, but their exact location depends on the make, model, and year of your vehicle. Please consult your owner’s manual if you are unsure of where your HomeLink is.
How can I configure HomeLink?
Release the HomeLink(r) system’s two exterior buttons after pressing and holding them until the LED begins to blink. Return to the vehicle and push the pre-programmed HomeLink (r) button four times while the LED on the garage door opener is blinking. (Or up to the point the garage door opens)
Why won’t my HomeLink function?
Interference close to the house or car, the use of stale batteries in the original transmitter during programming, or other factors can affect range.
- Your handheld transmitter needs a fresh battery. More power is drawn from the battery when the HomeLink(r) is being trained than when you press the doorbell button. It can occasionally assist the portable transmitter pick up a better signal and extend its range by replacing the battery.
- Retrain the HomeLink by moving it to various positions and angles. Hold the portable transmitter 3 to 4 inches from the buttons at first, then 5 to 6 and even 6 to 8 inches. This can occasionally aid in obtaining a stronger HomeLink signal.
- Make use of fresh batteries in a second transmitter.
- Adjust the antenna wire that hangs from the motorhead of the garage door opener.
The HomeLink button is what, exactly?
A widely used and trusted vehicle-based wireless control system is Homelink. You can use it to effortlessly open and close your front gate and garage door, turn on and off your home’s security system, and control your lighting, appliances, and electronics.
Can HomeLink be paired without a remote?
Try pressing the preprogrammed button to see if your garage door opens and closes. If it does, your effort has been fruitful. In the event that it doesn’t, repeat the process.
You may move a few little switches around to create any passcode you like. It should be comparable to the password on your phone. You won’t replace it unless you decide it’s no longer secure, at which point it will stay the same.
Note: If you have an earlier HomeLink garage door opener, there are no instructions for configuring it without a remote. In the HomeLink system, a code cannot be manually set. You need to utilize a remote to program it.
Most of the steps are the same. Make sure the door is shut, the key is not in the ignition, and any outdated programming is cleared away.
- Simply push both the remote button and the HomeLink button you wish to program while holding the remote up to the HomeLink button.
- Hold them until you notice the in-car remote’s LED starting to flash quickly.
What can I use HomeLink with?
Compatible Works with almost every gate system and garage door opener in addition to an expanding number of other radio-frequency (RF) controlled devices.
Smarter HomeLink 5 can inform you whether you left your garage door open or closed if your garage door is compatible.
Convenient HomeLink can control up to three devices and is completely integrated into the inside of your car.
Battery-free HomeLink never requires batteries because it is powered by the electrical system in your car.
Complementary Apps let you to manage your RF equipment when you’re not at home. HomeLink gives you quick, always-available functionality when you’re driving.
My HomeLink button is red; why is that?
When you press it again, the light ought to be red. This indicates that your 3-button remote is now prepared for HomeLink(r) system programming.