There is a rubber grommet on the brake pedal where it connects the brake light switch, which is a straightforward remedy for the brake lights that were staying on. The grommet has become worn,
In This Article...
Error in the brake light switch
A broken brake light switch is a common reason why a car’s brake lights won’t turn on. This part is attached close to the brake pedal under your dash. Your light switch may be stuck closed or the component may have failed if your lights are out.
Other signs of a broken brake light switch include malfunctioning brake lights, impaired cruise control, a car that won’t shift out of park, and brake lights that come on while you’re driving.
Kalikiano
I also have a problem with the nylon pad being missing. Can you buy the nylon pad? Even the brake pedal assembly at the Hyundai parts page doesn’t display it!
Surprise, surprise, I had the same same issue with my 1996 Elantra GLS Wagon. Wifey saw that the brake lights were all on when I pulled into the garage and turned off. I was perplexed and had no idea, but I was aware that if I didn’t rapidly fix the problem, the battery would progressively lose power. A little circular plastic disc with a diameter of about 18 mm and a thickness of about 4 mm was discovered on the floorboard of the driver’s side of the vehicle. When I Googled “Brake lights won’t turn off,” the first result was a brief YOU-Tube video explaining that the issue was likely caused by the failure of a little circular plastic (transparent nylon) pad that was called an oddly named “brake pedal bumper.” The video’s creator admitted that his Ford F**kus had the issue, but claimed that this was a typical engineering characteristic seen on the brake pedals of the majority of cars. When that small bumper pad was checked (it is located between the switch plunger and the brake pedal actuation lever), it was evident that it had failed (at about 131K miles). I therefore purchased a spare pad from the nearby Hyundai dealer after disconnecting the brake lights fuse from the fuse panel (to protect the battery). They were about $3, so I bought a few extras because a small flaw like this can lead to a variety of problems (e.g., leaving your stop lights on will make the bulbs extremely hot and may eventually cause the wiring to melt; your car won’t let you shift into DRIVE if the brake lights fuse has been removed; 2. disconnecting the battery is NOT an option because doing so’resets’ the “check engine” device; etc.).
By the way, the part number for all Hyundai Elantra models from 1996 to 2000 is 109D-32876-25000 (“Stopper-Pedal”). There is an image of the young offender attached (both the broken one and two of the new replacements).
Number One: A bad brake light switch
It is possible for the brake light switch at the lever to malfunction. When you push the pedal, it seems to move as it should, but it won’t turn off the electrical signal that turns on the brake lights.
Because auto makers create this specific switch to be incredibly reliable, this is an exceptional failure. However, it is still possible for it to malfunction and leave your brake lights on all the time. As long as your body is flexible enough to reach the switch, replacing it is not too difficult. If not, consult your mechanic about a replacement.
In some automobiles, the brake light switch plunger makes contact with the brake pedal lever’s rubber or plastic bumper. This bumper may malfunction, come apart, or fall off. The switch plunger will extend in the absence of a bumper, turning on the brake lights.
The issue can be this failing bumper if your brake lights won’t switch off and you discover small pieces of plastic (or rubber) beneath your feet. For repairs, speak with your mechanic. This issue is prevalent on a number of Honda, Hyundai, and Mazda models.
Stopper or a broken brake light switch
The brake light switch can still be in the engaged position if the brake lights are on while the engine is off. Many automobiles include a plastic stopper at the top of the brake pedal that, when the pedal is not being used, disengages the switch. This plastic stopper can shift or break occasionally, which keeps the switch engaged and the brake lights on.
Under the dash, at the brake pedal’s top, is where you’ll find the switch. Have a helper stand behind the car. Verify that the pedal’s stopper is in place. To access the switch, depress the brake pedal, then depress the brake light switch button.
The switch may need to be changed if this does not completely depress or if the brake lights are not turned off. Disconnecting the battery provides a temporary fix for this issue, but if you need to reach the battery later, it’s not a good idea if the hood latch is electronic rather than cable-operated.
If doing so disables the brake lights, the stopper most likely isn’t actuating the switch. Replace the stopper with a new one, or tape something with a width similar to the stopper, like a penny, for a temporary remedy. This should make the switch inoperative until the stopper is changed.
How to Fix Brake Lights Staying On (12 Tips)
One of the most crucial parts of a car is its brake lights (or taillights). They make use of a switch that activates the bulbs when the brake pedal is depressed. Brake lights flash when you are ready to slow down or stop, alerting any vehicles behind you. However, when they become stuck, these lights lose their function as a safety feature and may endanger both you and other people.
Circuit failures, issues with the brake assembly, and low brake fluid levels are some of the most typical causes of brake lights that remain on. While some problems are easy to diagnose and resolve, other problems are brought on by untidy auto parts.
Here are some typical solutions for brake lights that won’t go off:
- Check for damage on the brake light switch.
- Putting out blown fuses
- replacement of the brake light switch
- Keep the brake pedal bumper in working order.
- Change any burned-out bulbs.
- Remove the vehicle battery.
- Keep the brake pedal clean.
- Make sure the brake pedal effectively activates the switch.
- Ensure that your brake sockets are spotless.
- Don’t reduce your BCM.
- have enough brake fluid
- Turn off the parking brake.
The most popular solutions to brake light sticking are listed in this article. If necessary, it also explains how to replace your bumper and brake light switch. Stay tuned to discover more about how to maintain the appropriate operation of your car’s safety features, which is what this article seeks to provide for vehicle owners.
Why won’t the brake lights on my 2012 Hyundai Sonata turn off?
Due to a problem with the brake pedal assembly that, in certain cases, prevents the brake lights from turning off, Hyundai is recalling 304,900 Sonata cars from the 2011 and 2012 model years.
The brake pedal stopper pad, which can eventually wear down and allow the brake light switch to stay on after the driver lifts their foot from the brake pedal, is at problem. In these circumstances, the Sonata is capable of continuing to drive while the brake lights are illuminated in the “braking” position, which can give other motorists the wrong impression. Additionally, this issue can make it possible to shift out of park without depressing the brake pedal. Even while Hyundai reports that the second issue hasn’t resulted in any accidents, it is this second issue that is more concerning.
The Hyundai Sonata automobiles produced from December 11, 2009, to June 30, 2011, are subject to the recall campaign.
On January 11, Hyundai will begin the recall procedure, and dealers will apply the repair. Owners may bring their cars in to have this problem addressed at no charge; the fix simply entails installing a new stopper pad.
Owners should reach Hyundai customer service directly at 1-855-671-3059 and reference recall number 136 prior to the start of the recall. They can also visit the National Highway Traffic Safety Administration (NHTSA) website at www.safercar.gov or dial the vehicle safety hotline at 1-888-327-4236.
Ramey, Jay
For his own personal use, Jay Ramey has been drawn to the more adventurous end of the reliability spectrum because he spent his childhood around really unusual European cars.
Why do the brake lights on my Hyundai Santa Fe keep coming on?
Bad Switch: A faulty or failed switch is a typical cause of the Parking Brake light remaining on. You may quickly verify this by jiggling the handle once it has been lowered. The switch is most likely to be the problem and needs to be replaced if the light goes out (or goes out and comes back on).
If the brake handle is not fully down, there is another factor that could cause the light to remain on. Verify again that the parking brake is released and that the handle is fully lowered. The light will remain on if the parking brake cable is under any stress.
Parking Brake Not Disengaging: Occasionally, the parking brake itself is the source of the issue rather than the switch or the wires. The dash warning light will remain on if the brake does not release when the handle is dropped.
Low Brake Fluid: Your Parking Brake light is a multipurpose device that is intended to turn on when the reservoir’s fluid level falls below a specific level. As the fluid level fluctuates, you might see the light turning on or off when making turns.
The brake fluid level sensor in your master cylinder is malfunctioning. It is sometimes integrated into the reservoir cap, and other times it is positioned on the side of the sensor. The Parking Brake light will come on if the sensor malfunctions or becomes faulty.
Uneven Fluid Pressure: If your automobile has uneven brake fluid pressure in one or more lines, it may influence how well it can stop and may even cause it to pull to one side or the other. The parking brake light in your dash can also be activated by it.
Why do my Hyundai Sonata’s tail lights remain on while the engine is off?
The cabin fuse box is frequently the source of issues. To solve the issue, the assembly must be entirely replaced.
Are the brake lights on the Hyundai Sonata being recalled?
To find out if your vehicle is impacted by the Stop Lamp Switch Recall Campaign, enter your VIN.
Hyundai has made the decision to replace the stop lamp switches on various vehicles with model years 2007–2011 as part of a voluntary safety recall in the United States. Affected vehicles include the Accent, Elantra, Genesis Coupe, Santa Fe, Sonata, Tucson, and Veracruz. Hyundai notified the NHTSA of this action on March 29, 2013.