Due to a problem with the brake pedal assembly that, in certain cases, prevents the brake lights from turning off, Hyundai is recalling 304,900 Sonata cars from the 2011 and 2012 model years.
The brake pedal stopper pad, which can eventually wear down and allow the brake light switch to stay on after the driver lifts their foot from the brake pedal, is at problem. In these circumstances, the Sonata is capable of continuing to drive while the brake lights are illuminated in the “braking” position, which can give other motorists the wrong impression. Additionally, this issue can make it possible to shift out of park without depressing the brake pedal. Even while Hyundai reports that the second issue hasn’t resulted in any accidents, it is this second issue that is more concerning.
The Hyundai Sonata automobiles produced from December 11, 2009, to June 30, 2011, are subject to the recall campaign.
On January 11, Hyundai will begin the recall procedure, and dealers will apply the repair. Owners may bring their cars in to have this problem addressed at no charge; the fix simply entails installing a new stopper pad.
Owners should reach Hyundai customer service directly at 1-855-671-3059 and reference recall number 136 prior to the start of the recall. They can also visit the National Highway Traffic Safety Administration (NHTSA) website at www.safercar.gov or dial the vehicle safety hotline at 1-888-327-4236.
Ramey, Jay
For his own personal use, Jay Ramey has been drawn to the more adventurous end of the reliability spectrum because he spent his childhood around really unusual European cars.
In This Article...
AUTOSPARK
Turn on your headlights, then check the brake lights at the back of the vehicle. While keeping an eye on the high level (3rd) brake light, unplug the harness connector from each of the rear lamp units if they are on. There is a short circuit between the tail light and brake light circuits in that lamp unit if the high level brake light turns off when you unplug one of the bulbs. It will almost certainly be brought on by a misplaced or defective bulb.
You might not get a response because this is an old thread, and you might be restarting an old thread. Consider starting a new thread, please.
Hyundai Forum is a place where all Hyundai Owners can gather to discuss and learn everything there is to know about Hyundai vehicles, including the Sonata, Elantra, and even the brand-new Kona!
Common causes of this include:
Bad Switch: A faulty or failed switch is a typical cause of the Parking Brake light remaining on. You may quickly verify this by jiggling the handle once it has been lowered. The switch is most likely to be the problem and needs to be replaced if the light goes out (or goes out and comes back on).
If the brake handle is not fully down, there is another factor that could cause the light to remain on. Verify again that the parking brake is released and that the handle is fully lowered. The light will remain on if the parking brake cable is under any stress.
Parking Brake Not Disengaging: Occasionally, the parking brake itself is the source of the issue rather than the switch or the wires. The dash warning light will remain on if the brake does not release when the handle is dropped.
Low Brake Fluid: Your Parking Brake light is a multipurpose device that is intended to turn on when the reservoir’s fluid level falls below a specific level. As the fluid level fluctuates, you might see the light turning on or off when making turns.
The brake fluid level sensor in your master cylinder is malfunctioning. It is sometimes integrated into the reservoir cap, and other times it is positioned on the side of the sensor. The Parking Brake light will come on if the sensor malfunctions or becomes faulty.
Uneven Fluid Pressure: If your automobile has uneven brake fluid pressure in one or more lines, it may influence how well it can stop and may even cause it to pull to one side or the other. The parking brake light in your dash can also be activated by it.
Answers
I own a Santa Fe from 2006. Today I took it to Pep Boys for an oil change. When I parked my car at home, I noticed that all three of the back brake lights—two standard and one middle “high” one—were on. All of the other lights were out, but these 3 lights were left on. I thus grabbed my needle nose pliers, unlocked the fuse box, and pulled 5 fuses after carefully inspecting the fuse box’s interior cover. Yeah! I am not a mechanic, but I am aware that I pulled out two for no reason! 12-year-old vehicle I’m prepared to throw it away by August. I’ll utilize hand signals to signal braking and stopping till then.
Do not scrap your vehicle for that reason. I own a 2004 Santa Fe, and both of my brake lights are not working.
The one in the middle continued as well. Online provided clear instructions, so we only had to
I paid roughly $9 at O’Reilly for a generic stop pad. Actually, there are two included: a plastic and
an elastic one. Since it was simpler to cut and fit into the little hole of the plastic one, I used it.
depressed. I applied enough pressure to the brake pedal to insert a screwdriver blade.
The lights were switched off using the pad and switch. Two 14mm nuts are present on the
To completely engage the switch, turn the mounting bracket a few turns.
Why do your brake lights continue to illuminate?
One of the most crucial parts of a car is its brake lights (or taillights). They make use of a switch that activates the bulbs when the brake pedal is depressed. Brake lights flash when you are ready to slow down or stop, alerting any vehicles behind you. However, when they become stuck, these lights lose their function as a safety feature and may endanger both you and other people.
Circuit failures, issues with the brake assembly, and low brake fluid levels are some of the most typical causes of brake lights that remain on. While some problems are easy to diagnose and resolve, other problems are brought on by untidy auto parts.
Here are some typical solutions for brake lights that won’t go off:
- Check for damage on the brake light switch.
- Putting out blown fuses
- replacement of the brake light switch
- Keep the brake pedal bumper in working order.
- Change any burned-out bulbs.
- Remove the vehicle battery.
- Keep the brake pedal clean.
- Make sure the brake pedal effectively activates the switch.
- Ensure that your brake sockets are spotless.
- Don’t reduce your BCM.
- have enough brake fluid
- Turn off the parking brake.
The most popular solutions to brake light sticking are listed in this article. If necessary, it also explains how to replace your bumper and brake light switch. Stay tuned to discover more about how to maintain the appropriate operation of your car’s safety features, which is what this article seeks to provide for vehicle owners.
Why wouldn’t my brake lights illuminate?
A broken brake light switch is a common reason why a car’s brake lights won’t turn on. This part is attached close to the brake pedal under your dash. Your light switch may be stuck closed or the component may have failed if your lights are out.
Other signs of a broken brake light switch include malfunctioning brake lights, impaired cruise control, a car that won’t shift out of park, and brake lights that come on while you’re driving.