Bad Switch: A faulty or failed switch is a typical cause of the Parking Brake light remaining on. You may quickly verify this by jiggling the handle once it has been lowered. The switch is most likely to be the problem and needs to be replaced if the light goes out (or goes out and comes back on).
If the brake handle is not fully down, there is another factor that could cause the light to remain on. Verify again that the parking brake is released and that the handle is fully lowered. The light will remain on if the parking brake cable is under any stress.
Parking Brake Not Disengaging: Occasionally, the parking brake itself is the source of the issue rather than the switch or the wires. The dash warning light will remain on if the brake does not release when the handle is dropped.
Low Brake Fluid: Your Parking Brake light is a multipurpose device that is intended to turn on when the reservoir’s fluid level falls below a specific level. As the fluid level fluctuates, you might see the light turning on or off when making turns.
The brake fluid level sensor in your master cylinder is malfunctioning. It is sometimes integrated into the reservoir cap, and other times it is positioned on the side of the sensor. The Parking Brake light will come on if the sensor malfunctions or becomes faulty.
Uneven Fluid Pressure: If your automobile has uneven brake fluid pressure in one or more lines, it may influence how well it can stop and may even cause it to pull to one side or the other. The parking brake light in your dash can also be activated by it.
In This Article...
Due to the same issues that led to an earlier Hyundai Sonata recall, Hyundai is recalling 64,500 Elantra vehicles.
Hyundai is recalling 64,500 Elantra models from the 2013 model year in order to remedy brake light switch issues brought on by brake pedal stopper pads.
Between the stop light switch and the brake pedal arm lies the brake pedal stopper pad. According to Hyundai, the material of the brake pedal stopper pad may degrade with time, causing the stop light switch plunger to stay extended when the brake pedal is removed.
As a result, both the traction control warning light and the brake lights will be illuminated continuously.
In addition, the switch has the ability to move the shift lever without depressing the brake pedal, allowing the automobile to be moved out of PARK without applying any braking pressure.
Hyundai started looking into warranty claims concerning the replacement of brake pedal stopper pads for several models in July 2014. According to the information available, Hyundai recalled Sonata vehicles in November 2015 to correct the switches, and in the second quarter of 2016, it saw a gradual rise in the number of warranty claims for some Elantra sedans.
Even though there have been numerous recalls due to brake light switch issues, Hyundai claims it is still looking into the supplier and any significant adjustments made by the business.
On September 30, 2016, the Elantra recall is expected to start. Hyundai dealers will swap out the brake pedal stopper pad for a purportedly better component.
Call 855-371-9460 and ask for details regarding Hyundai’s recall number 146 if you own a 2013 Elantra and have questions about it.
Hyundai has experienced brake light switch issues in the past, although for different causes. The brake lights can stay on with the Elantra recall, but they didn’t light up at all with other recalls linked to brake light switches.
Hyundai recalled more than 1 million vehicles in April 2013 to fix the same faulty switches. The 2007–2009 Accent and Tucson, 2007–2010 Elantra, 2007–2011 Santa Fe, 2008–2009 Veracruz, 2010–2011 Genesis Coupe, and 2011 Sonata were all affected by the recall.
The same brake light switches were recalled by Kia in April 2013 for 623,000 vehicles, including the 2007–2010 Kia Rondo and Sportage, 2007–2011 Kia Sorento, 2007 Kia Sedona, 2010–2011 Kia Soul, and the 2011 Kia Optima.
The Hyundai Accent was subsequently recalled in September 2015 to address issues with the brake light switch.
Defective switches were causing problems with the push-button start system, the cruise control staying on when it wasn’t needed, the brake lights failing, and the gear selector getting stuck in park.
Reply
EXPERT
The brake pedal is underneath the dash, and that is also where the brake light switch resides. To unhook it, you’ll have to lie on your back, which is incredibly uncomfortable. Then, to remove the retaining nut, use a wrench or a good pair of pliers. Then it ought to just come out. The new one will need to be adjusted after installation. I’ve added Prodemand’s adjusting guidelines.
It’s also possible that you only need to tweak the switch you currently have. Use the directions below once more.
Kalikiano
I also have a problem with the nylon pad being missing. Can you buy the nylon pad? Even the brake pedal assembly at the Hyundai parts page doesn’t display it!
Surprise, surprise, I had the same same issue with my 1996 Elantra GLS Wagon. Wifey saw that the brake lights were all on when I pulled into the garage and turned off. I was perplexed and had no idea, but I was aware that if I didn’t rapidly fix the problem, the battery would progressively lose power. A little circular plastic disc with a diameter of about 18 mm and a thickness of about 4 mm was discovered on the floorboard of the driver’s side of the vehicle. When I Googled “Brake lights won’t turn off,” the first result was a brief YOU-Tube video explaining that the issue was likely caused by the failure of a little circular plastic (transparent nylon) pad that was called an oddly named “brake pedal bumper.” The video’s creator admitted that his Ford F**kus had the issue, but claimed that this was a typical engineering characteristic seen on the brake pedals of the majority of cars. When that small bumper pad was checked (it is located between the switch plunger and the brake pedal actuation lever), it was evident that it had failed (at about 131K miles). I therefore purchased a spare pad from the nearby Hyundai dealer after disconnecting the brake lights fuse from the fuse panel (to protect the battery). They were about $3, so I bought a few extras because a small flaw like this can lead to a variety of problems (e.g., leaving your stop lights on will make the bulbs extremely hot and may eventually cause the wiring to melt; your car won’t let you shift into DRIVE if the brake lights fuse has been removed; 2. disconnecting the battery is NOT an option because doing so’resets’ the “check engine” device; etc.).
By the way, the part number for all Hyundai Elantra models from 1996 to 2000 is 109D-32876-25000 (“Stopper-Pedal”). There is an image of the young offender attached (both the broken one and two of the new replacements).
Why do your brake lights continue to illuminate?
One of the most crucial parts of a car is its brake lights (or taillights). They make use of a switch that activates the bulbs when the brake pedal is depressed. Brake lights flash when you are ready to slow down or stop, alerting any vehicles behind you. However, when they become stuck, these lights lose their function as a safety feature and may endanger both you and other people.
Circuit failures, issues with the brake assembly, and low brake fluid levels are some of the most typical causes of brake lights that remain on. While some problems are easy to diagnose and resolve, other problems are brought on by untidy auto parts.
Here are some typical solutions for brake lights that won’t go off:
- Check for damage on the brake light switch.
- Putting out blown fuses
- replacement of the brake light switch
- Keep the brake pedal bumper in working order.
- Change any burned-out bulbs.
- Remove the vehicle battery.
- Keep the brake pedal clean.
- Make sure the brake pedal effectively activates the switch.
- Ensure that your brake sockets are spotless.
- Don’t reduce your BCM.
- have enough brake fluid
- Turn off the parking brake.
The most popular solutions to brake light sticking are listed in this article. If necessary, it also explains how to replace your bumper and brake light switch. Stay tuned to discover more about how to maintain the appropriate operation of your car’s safety features, which is what this article seeks to provide for vehicle owners.
Why do brake lights remain on while the car is not moving?
Your battery will become discharged if your brake lights are left on. While the automobile is off or until this problem is fixed, you must unplug your battery.
The brake light switch sticking closed is the most likely reason why the brake lights are still on. If the lights don’t turn off, you might try unplugging the brake light switch at the pedal. If they do, a new brake light switch is required. If not, you will require more electrical diagnosis.
The informative nature of the aforementioned claims warrants independent verification. kindly visit our
Repairing brake lights at AutoZone?
AutoZone will they replace brake lights? Although AutoZone doesn’t really provide brake light replacement services, our staff can help you with any inquiries you may have, aid you in locating the necessary supplies to get started, and perhaps even lend a hand.
Do brake lights get fixed at Walmart?
Sadly, Walmart Auto Care Centers do not offer any brake-related services, including maintenance for brake pads, sensors, fluids, taillights, and brake lights. Walmart sells replacement brake light bulbs, so you can buy one and install it yourself. Walmart does not install brake lights.
How can a brake light that won’t turn off be fixed?
Cause #2 of Brake Lights Not Turning Off: Parking Brake Sometimes the issue is right in front of us, but we are unable to notice it. Keeping the parking brake engaged is a very basic problem that causes the brake lights to remain illuminated. To resolve the issue, only fully release the parking brake.
Where is the sensor for the brake lights located?
A little gadget connected to the brake pedal mechanism is called a brake light switch. The brake light switch, despite its diminutive size, has a significant function in contemporary automobiles.
If a brake light switch is malfunctioning, many vehicle functions, such as Push-Button Start, Antilock Brakes, and Vehicle Stability Control, will not function.
There are two main purposes for the brake light switch. When a driver depresses the brake pedal, it first activates the brake lights. Second, it informs the car’s computer that the brakes are being used. Driving a car with a broken brake light switch is VERY RISKY.
The brake light switch is typically located just over the brake pedal. It has a one-way or two-way electric switch within. Brake lights that don’t turn on or that stay on all the time are the most typical signs of a broken brake light switch.
How can I tell if my brake light switch needs to be repaired?
You’ve checked the brake light fuse and the brake light bulbs, but the power to those areas is still not working. You should in this case examine the brake light switch. It is a device that joins and completes the electrical circuit for the brake lights in a car. It’s a relatively straightforward two-wire switch, with one wire controlling power coming in and the other controlling power leaving.
The switch, which is close to the brake pedal, is probably marked. Get your test light out once more, and ground it just like you did when you examined the fuses. Place the sensor on just one of the two wires while maintaining a firm grip on the brake pedal. Next, examine the other wire. The test lamps will light up if the switch is functioning properly and the power is connected. The brake light switch needs to be replaced if it doesn’t illuminate. Use the owner’s manual to find the major “power in” and “power out” lines if your switch has a more intricate design with more than two wires. Then, test those wires.
If you try all of these solutions and your brake lights still don’t function, there may be other systems in your car that require inspection. For instance, if your car’s turn signals and brake lights are wired together, you’ll need to check those systems’ fuses. Modern automobiles come equipped with an exclusive “brake light control module,” an integrated computer system, and onboard diagnostic scans to identify any issues.
Generally speaking, repairing a car’s brake lights is simple, but there are times when you should seek the advice of a qualified mechanic. It’s crucial to get those lights fixed as quickly as possible, whatever your car needs.