Under the steering wheel is typically where you’ll find the TPMS reset button.
In This Article...
How should I respond if the tire pressure sign illuminates?
The Hyundai Tucson is a fantastic vehicle, and if there is a problem with the tires, you will get a warning sign on your LED screen.
The graphic will clearly show you the problem the automobile has identified as well as which tires require attention.
Once the tire pressure has been adjusted to the proper PSI (this information can be found on the door placard or in your user manual.) You might observe that the sensors’ recalibration can take some time.
You might want to calibrate the tire pressure monitoring device by following the straightforward instructions below if you believe the light should have turned off but hasn’t:
- Take a long drive while maintaining a constant speed of 50 mph; this will reset the pressure system and turn off the light.
Check out these more suggestions to try if this one doesn’t work:
- The TPMS reset button may need to be identified; it is typically found under the steering wheel. Check your user manual for its location if you can’t find it.
- Once you’ve found it, turn on the ignition of the automobile, but do not start the engine. When the button blinks three times, let go of it.
- The sensor may need to refresh for 20 minutes or so before you may start the car.
Other pointers for resetting the TPMS light are as follows:
- All tires, including the spare, should be steadily inflated to slightly over the recommended PSI. Then totally deflate each tire. Once this has been accomplished, properly PSI-inflate the tires.
- It may be necessary to unhook the battery cable from the sensor, start the vehicle, and honk the horn for a few seconds in order to deplete the sensor’s power. This will release any remaining power in the car.
- When you’re done, re-connect the battery, and the TPMS should be fixed.
Visit a Hyundai dealership so that they may conduct a thorough sensor health check if you’ve noticed that the light is still on.
Low tire pressure reset
On the Hyundai Tucson, there is no option to restore low tire pressure. Drive your car for 5–10 miles if you notice the warning symbol and all of your tires are inflated to the required levels. You will need to go to your local Hyundai dealership to have all the sensors professionally inspected if the warning light is still on.
The warning light on some Kia vehicles shuts off when the air pressure is topped off, despite the fact that this is not advised. If the suggested air pressure for your car is 32, for instance, try filling it up to 35 and then driving for a few miles. Remember that increased air pressure may reduce driving comfort and result in uneven tire wear.
The individual tire pressures won’t be visible on the cluster LCD display if the TPMS isn’t working properly.
- After a brief drive, check the tire pressure monitoring system display in the instrument cluster to frequently check your tire pressure, such as once a week.
- Please be aware that, especially if your car isn’t used frequently, tires might naturally lose one to two PSI per month.
- Also keep in mind that tire pressures can change with temperature, so it’s best to check them right as you start your car up.
- Verify that your tires are properly inflated in accordance with the information placard on the driver’s side door jam of your car.
to restart The tire must be inflated to at least 35 psi. For more than a week, I attempted this with 32. Go above 35, a friend said. Drive it; I turned it off, but when I turned it back on, it was broken. The answer is 35.
After inflation, how do you turn the light off? I keep asking that, but all I get are these useless answers!
Hyundai Tucson Reset Tire Pressure
Resetting low tire pressure is not an option on the Hyundai Tucson. Drive for 5 to 10 miles if the warning symbol shows and all of your car’s tires are inflated to the proper levels. You must take your Hyundai to a Hyundai dealership if the warning light is still on so that all of the sensors may be expertly inspected.
Though it is not advised, some Hyundai vehicles’ warning lights switch off when the air pressure is inflated above the suggested level. For instance, if your car’s tires should have 32 psi of air pressure, try filling them with 35 psi and driving a few kilometers. Remember that higher air pressure might make driving less comfortable and lead to uneven tire wear.
The individual tire pressures shown in the cluster LCD display won’t be available if the TPMS malfunctions.
On the Hyundai Tucson, where is the TPMS button?
Usually found somewhere under the steering wheel, the reset button for the tire pressure monitoring system. When the tire pressure monitor system light blinks three times, hold down the reset button.
How is the TPMS on a 2022 Tucson reset?
- Put the car in park.
- Start the engine.
- Until the Settings menu shows on the screen, continually press the Mode button on the steering wheel.
- To scroll to the Tire Pressure screen, press the downarrow key.
- Each tire’s pressure should be checked.
- The screen will display the low-pressure tire.
What is the Hyundai Tucson’s TPMS?
Hyundai vehicles are equipped with TPMS, or tire pressure monitoring systems, which may detect low tire pressure in any of the car’s four tires and issue an alert. According to the table below, a TPMS from one of two manufacturers is installed as a component of the valve assembly in every Hyundai vehicle.
According to the table below, a TPMS from one of two manufacturers is installed as a component of the valve assembly in every Hyundai vehicle. The tire pressure monitor ECU/receiver receives the data from the sensor, which detects the pressure and temperature inside the tire, together with the TPMS’s distinctive ID.
If the TPMS ID is stored with the ECU, the placard pressure is checked with it, and if there is a pressure difference, a warning light is illuminated on the dash-mounted display.
How is the TPMS manually reset?
When the tire pressure light blinks three times, release pressure on the TPMS reset button. For the sensors to reset, start the car and let it run for 20 minutes. The button to reset the tire pressure monitor is under the steering wheel.
What does a Hyundai’s check TPMS mean?
The TPMS (Tire Pressure Monitoring System) is designed to notify you when a tire’s pressure is too low and may result in hazardous driving situations. If the indicator is on, your tires may not be properly inflated, which might result in premature tire wear and even tire failure. It’s critical to comprehend the value of appropriate tire inflation and how TPMS can prevent a potentially hazardous situation.
Both excessive and inadequate tire inflation can result in early tread deterioration and potential tire failure. Increased traction, early wear, and an inability to withstand impact from the road can all be effects of overinflation. The middle of the tread on tires with excessive air pressure may prematurely wear out. Underinflation, on the other hand, results in slow tire reaction, lower fuel economy, excessive heat buildup, and tire overload. The shoulders or tread edges of a tire that is underinflated will prematurely wear out on both sides.
Finding the TPMS indicator on your dashboard is straightforward if this is your first time hearing about tire pressure sensors. It is a light that has a horseshoe form with an exclamation point in the middle.
How is the TPMS reset after tire rotation?
It is common to need to re-program the tire pressure monitoring system after rotating your tires so it is aware of where each wheel’s pressure sensors went.
By pressing the TPMS reset button inside your car or truck, you can only erase any error codes that are responsible for your tire warning light appearing on your dash.
After rotating your tires, how do you reset your TPMS? After rotation, the majority of TPMS systems require new sensor position learning. It’s not always enough to merely push the TPMS reset button.
To inform the system of the new locations of the rotated tires and tire sensors, the system frequently needs a TPMS tool. The system may occasionally be able to locate the places automatically.
The process for the system to relearn the positions of the TPMS sensors will differ depending on the manufacturer, and occasionally even between various models made by the same manufacturer.
Learn more about some of the more typical techniques for instructing a tire pressure monitoring system to retrain TPMS sensor settings after tire rotations in the following paragraphs.
Does programming of Hyundai TPMS sensors are required?
Before being inserted in the tire, these sensors need to be programmed with the appropriate protocol/application information for the vehicle, and they then need to be retrained to the vehicle.
Has the spare tire on a Hyundai had TPMS?
The tire pressure monitoring system (TPMS) light may have illuminated on the dash while you were changing the spare tire if you had the unfortunate experience of getting a flat tire. How come? What you should know is as follows:
The TPMS light on the dash illuminates because the spare tire cannot provide a reading because it lacks a TPMS sensor.
You should only need to travel a few miles after replacing the damaged wheel and tire with the original ones for the car to turn off (the TPMS system just needs to check the system and rest the light).
Check TPMS System will also be displayed if your vehicle has a multi-information display. After the regular wheel is put back on the automobile, this will disappear.
The informative nature of the aforementioned claims warrants independent verification. kindly visit our
Does the Hyundai warranty include TPMS?
Hyundai’s new vehicle limited warranty covers the tire pressure sensor for the vehicles included in this recall for five years or 60,000 miles.
Should the TPMS be reset after purchasing new tires?
After changing or rotating your tires, or after adding new sensors, you should always reset your TPMS. Even after you have inflated your tires, some sensor manufacturers advise restarting the device. By teaching the primary TPMS system to identify the sensors in their new locations, resetting the TPMS is frequently referred to as retraining the system. TPMS reset procedures vary from vehicle to vehicle and typically involve a specific sequence of ignition and pedal actions, a configuration change in your dashboard menu, or the use of a TPMS Reset Tool.
Where are TPMS installed?
Where is the location of the tire pressure sensor? It is affixed to the interior of the rim from inside the tire. The tire pressure sensor is a little cylinder that you can see if you take the tire off the rim.
What is the price of a new TPMS sensor?
Depending on the type of car, the cost to replace the TPMS sensors might be anywhere from $50 and $100 per.
Because servicing TPMS needs additional parts, tools, and labor, TPMS-equipped tires are slightly more expensive to maintain than non-equipped tires. Every time a tire is removed from the vehicle for maintenance or replacement, the TPMS valve service kit, which consists of the valve core, (sealing) cap, nut, and grommet (stem seal), needs to be replaced. On most automobiles, the service kit is between $5 and $10 per wheel. The TPMS system needs to be checked and reset, which takes additional time and a special TPMS programming tool.
A service pack should be used to replace the sealing components of the sensor, which comprise the cap, valve core, grommet, nut, and any other accessory included in the service pack, according to Schrader(r), a producer of original equipment TPMS sensors. The integrity of the TPMS sensor and valve is guaranteed by replacing the service pack components.
TPMS are in my automobile. I haven’t had my repair shop service it yet. What should I anticipate when I arrive?
- Checking the system’s sensors and TPMS for appropriate operation
- Any component of your TPMS sensors that is malfunctioning should be repaired or replaced.
- Your vehicle’s computer will need to “relearn” how to place the TPMS sensors by doing this.
- After the tire service is finished, make sure your TPMS system is functioning properly.
What happens if I have an additional set of wheels and tires (for snow tires or unique wheels)?
You can get a spare pair of tires or wheel assemblies fitted with a set of replacement sensors. Your TPMS installer will be able to relearn the new sensors to the vehicle computer after the extra set of tires or wheel assemblies are attached to the vehicle. The sensors will need to be relearned to the vehicle computer when the original set of tires or wheel assemblies are reinstalled on the vehicle.