Under the steering wheel is typically where you’ll find the TPMS reset button.
In This Article...
How to Reset the Tire Pressure Light on a Hyundai Santa Fe
- Drive the vehicle for around 10 minutes at 50 mph.
- Turn the ignition key to the “On” position without starting the automobile.
- After three seconds, or when the light has flashed three times, let go of the TPMS reset button.
- To reset and calibrate the sensor, start the engine and let the vehicle run for 20 minutes.
The reset button for the tire pressure monitor is often located under the steering wheel on Hyundai Santa Fe vehicles.
You could also wonder why the tyre pressure indicator is still on after the tires have been inflated. If your tire pressure monitoring system is malfunctioning or there is a persistent leak, the air pressure warning light may continue to glow even after you have inflated your tires.
Use a pressure gauge to confirm that the tire is properly inflated to the recommended air pressure if the TPMS warning light comes on again after you’ve inflated it.
Tire Pressure Sensor Reset
Identify the TPMS system type.
If the direct system is employed by your 2019 Hyundai Santa Fe, resetting the tire pressure sensors might only require pressing a reset button on the dash or navigating a menu as described in your owner’s handbook. If your 2019 Hyundai Santa Fe has an indirect system, it must be reset by a dealer or one you have personally purchased using a magnet or scanning equipment. In order to reset some systems, the ignition must be turned on while the reset button is pressed and held down for three seconds within the glove box.
Pump up the tires.
Ensure that all tires are inflated appropriately. All tires must be fully inflated because you are resetting the sensors to “zero,” or else the sensors won’t be properly calibrated and their readings will be off.
Evaluate the battery.
If the sensor in your 2019 Hyundai Santa Fe is powered by a battery, make sure it is not dead. The battery should be changed every five years. Since the battery is integrated, in certain cases this necessitates replacing the complete sensor unit.
Make the transponders new.
Every wheel has a unique transponder. Each responder’s location changes when the wheels are rotated, and the TPMS needs to learn their new locations. Although this relearning process varies depending on the vehicle, you can get more information in the TPMS chart in your manual or online. If the valve stems double as tire pressure sensors, it is a good idea to swap them out when purchasing new tires.
Apply the magnet technique.
Press the lock and unlock buttons on the key fob when the key is in the ignition but the engine is not running. Placing a magnet over each valve stem after the initial chirp will cause the horn to chip for each valve in the following order: left front, right front, right rear, and left rear. Make that the driver information center is showing the pressure values.
Utilize the scan tool approach.
The owner’s manual’s TPMS Reprogramming Procedure menu prompts can be followed if no sensors are being replaced.
Where is the Hyundai Santa Fe 2012’s TPMS reset button?
When the tire pressure light blinks three times, release pressure on the TPMS reset button. For the sensors to reset, start the car and let it run for 20 minutes. The button to reset the tire pressure monitor is under the steering wheel.
On a 2020 Santa Fe, where is the TPMS reset button located?
Usually found somewhere under the steering wheel, the reset button for the tire pressure monitoring system. Till the tire pressure monitor system light blinks three times, keep the reset button depressed. The sensors should reset about 20 minutes after you restart the vehicle.
On a Hyundai Sonata, where is the TPMS reset button located?
Most likely, there is no reset button. You either have a tire with low air pressure or there is a problem with the TPMS system if the TPMS light is on. Verify the tire pressure.
What is the Hyundai Santa Fe’s TPMS?
Hyundai vehicles are equipped with TPMS, or tire pressure monitoring systems, which may detect low tire pressure in any of the car’s four tires and issue an alert. According to the table below, a TPMS from one of two manufacturers is installed as a component of the valve assembly in every Hyundai vehicle.
According to the table below, a TPMS from one of two manufacturers is installed as a component of the valve assembly in every Hyundai vehicle. The tire pressure monitor ECU/receiver receives the data from the sensor, which detects the pressure and temperature inside the tire, together with the TPMS’s distinctive ID.
If the TPMS ID is stored with the ECU, the placard pressure is checked with it, and if there is a pressure difference, a warning light is illuminated on the dash-mounted display.
Is there a TPMS on the 2017 Hyundai Santa Fe?
The tire pressure monitoring system (TPMS) in the impacted vehicles may not have been properly configured during vehicle assembly, which means it won’t issue the proper warning in the event of an underinflated tire.
The Federal Motor Vehicle Safety Standard (FMVSS) number 138, “Tire Pressure Monitoring Systems,” is not met by these vehicles.
Has the 2020 Santa Fe got TPMS?
We will examine the most popular 2019 cars, SUVs, minivans, and trucks during the coming months. We’ll concentrate on the top-selling SUVs in the US in 2019 during the month of April.
All American-made automobiles must have direct or indirect TPMS systems fitted as of 2008 as a result of the TREAD Act’s 2007 mandate.
The direct TPMS system is used in the production of the Hyundai Santa Fe. If one or more tires on a direct TPMS system indicate low tire pressure, the TPMS sensors will communicate this information to the vehicle’s ECU. Each tire pressure or an indicator light (low-line TPMS system) will be displayed on the dashboard (high-line TPMS system).
How can I turn my TPMS light back on?
When the tire pressure light blinks three times, release pressure on the TPMS reset button. Start the car and let it run for 20 minutes to let the sensor reset. Under the steering wheel is normally where you’ll find the reset button for the tire pressure monitor. If you can’t find it, consult the owner’s manual for your vehicle.
Does programming of Hyundai TPMS sensors are required?
Before being inserted in the tire, these sensors need to be programmed with the appropriate protocol/application information for the vehicle, and they then need to be retrained to the vehicle.
Where are TPMS installed?
Where is the location of the tire pressure sensor? It is affixed to the interior of the rim from inside the tire. The tire pressure sensor is a little cylinder that you can see if you take the tire off the rim.
Should the TPMS be reset after purchasing new tires?
After changing or rotating your tires, or after adding new sensors, you should always reset your TPMS. Even after you have inflated your tires, some sensor manufacturers advise restarting the device. By teaching the primary TPMS system to identify the sensors in their new locations, resetting the TPMS is frequently referred to as retraining the system. TPMS reset procedures vary from vehicle to vehicle and typically involve a specific sequence of ignition and pedal actions, a configuration change in your dashboard menu, or the use of a TPMS Reset Tool.
My TPMS light won’t turn off; why?
When the TPMS warning light illuminates, proceed with caution. This indicates that at least one of your tires may be at least 25% under-inflated.
*The simplest way to get the most accurate reading is to check the tire pressure before you drive on it when the tire is “cool.” If your TPMS light is on, first check that you have correctly reset your TPMS by following these instructions.
Will my TPMS light automatically turn off if I fill my tires with air after it illuminates?
Several minutes after reinflating the tires to the prescribed pressure, the TPMS light ought to go out.
What happens if I adjust the tire pressure but the light on my tire pressure gauge still doesn’t go out?
The only place that can fix a computer issue that causes the TPMS warning light to turn ON and flash ON for one second and OFF for three seconds is the dealership service center. When the TPMS warning light illuminates and remains on, one or more tires may have low tire pressure. The light ought to go out once the tire is inflated to the recommended tire pressure listed on the door placard. Always check the pressure in all of your tires because one or more of them may not be at the proper pressure.
My TPMS won’t retrain, why?
After correctly completing all steps, if the TPMS system does not reset, there may be a problem with interference between the sensor and the vehicle’s ECU, especially for larger trucks like the F-Series. Steps 6 and 8 should result in the sound chirping; otherwise, the relearn operation was unsuccessful.
What is the price of a new TPMS sensor?
Depending on the type of car, the cost to replace the TPMS sensors might be anywhere from $50 and $100 per.
Because servicing TPMS needs additional parts, tools, and labor, TPMS-equipped tires are slightly more expensive to maintain than non-equipped tires. Every time a tire is removed from the vehicle for maintenance or replacement, the TPMS valve service kit, which consists of the valve core, (sealing) cap, nut, and grommet (stem seal), needs to be replaced. On most automobiles, the service kit is between $5 and $10 per wheel. The TPMS system needs to be checked and reset, which takes additional time and a special TPMS programming tool.
A service pack should be used to replace the sealing components of the sensor, which comprise the cap, valve core, grommet, nut, and any other accessory included in the service pack, according to Schrader(r), a producer of original equipment TPMS sensors. The integrity of the TPMS sensor and valve is guaranteed by replacing the service pack components.
TPMS are in my automobile. I haven’t had my repair shop service it yet. What should I anticipate when I arrive?
- Checking the system’s sensors and TPMS for appropriate operation
- Any component of your TPMS sensors that is malfunctioning should be repaired or replaced.
- Your vehicle’s computer will need to “relearn” how to place the TPMS sensors by doing this.
- After the tire service is finished, make sure your TPMS system is functioning properly.
What happens if I have an additional set of wheels and tires (for snow tires or unique wheels)?
You can get a spare pair of tires or wheel assemblies fitted with a set of replacement sensors. Your TPMS installer will be able to relearn the new sensors to the vehicle computer after the extra set of tires or wheel assemblies are attached to the vehicle. The sensors will need to be relearned to the vehicle computer when the original set of tires or wheel assemblies are reinstalled on the vehicle.
Can I drive with my TPMS on?
To avoid seeming like Debbie Downer, we’ll simply say no. Driving around with your TPMS light on is not safe. You can’t tell how quickly your tire is losing air or how long it has been over- or underinflated without doing a tire examination. The best course of action is to check the current inflation level of each tire with a tire pressure gauge.
When the tire inspection light appears while you are driving, slow down and get to the closest gas station or service facility.
Can TPMS be re-learned without a tool?
Reset the TPMS Using Method 2 Without a Tool You might see the RELEARN TIRE POSITION option in some cars. That’s it. Step 3: Using your key fob, simultaneously push the Unlock and Lock buttons. Wait until the horn blasts twice; this indicates that the system is prepared to reset the sensors.