Find the brake light switch next to the pivot of the brake pedal lever, and note its position. Remove the electrical connector from the switch. Locate the locking plate next to the mounting bracket, underneath the switch body. To remove the plate from the assembly, gently squeeze the release tabs on the rear of the plate, then pull the tab on the front of the plate in your direction.
In This Article...
Replacement Services for Brake Light Switches
Hyundai Sonata Brake Light Switch Replacement typically costs $111, which includes $16 for parts and $95 for labor. Prices may change based on where you are.
Why does the brake light on my Hyundai Sonata remain on?
Bad Switch: A faulty or failed switch is a typical cause of the Parking Brake light remaining on. You may quickly verify this by jiggling the handle once it has been lowered. The switch is most likely to be the problem and needs to be replaced if the light goes out (or goes out and comes back on).
If the brake handle is not fully down, there is another factor that could cause the light to remain on. Verify again that the parking brake is released and that the handle is fully lowered. The light will remain on if the parking brake cable is under any stress.
Parking Brake Not Disengaging: Occasionally, the parking brake itself is the source of the issue rather than the switch or the wires. The dash warning light will remain on if the brake does not release when the handle is dropped.
Low Brake Fluid: Your Parking Brake light is a multipurpose device that is intended to turn on when the reservoir’s fluid level falls below a specific level. As the fluid level fluctuates, you might see the light turning on or off when making turns.
The brake fluid level sensor in your master cylinder is malfunctioning. It is sometimes integrated into the reservoir cap, and other times it is positioned on the side of the sensor. The Parking Brake light will come on if the sensor malfunctions or becomes faulty.
Uneven Fluid Pressure: If your automobile has uneven brake fluid pressure in one or more lines, it may influence how well it can stop and may even cause it to pull to one side or the other. The parking brake light in your dash can also be activated by it.
Why do my Hyundai Sonata’s brake lights not function?
The mechanic will bring a multimeter while inspecting the electric parts of your car, particularly the fuses and relays, to help them identify which particular part has failed. The mechanic will start by looking at the rear of the vehicle for any obvious damage, such as frayed or loose wiring and damaged tail light covers. The mechanic will next start to look at each component along the electrical circuit if there isn’t any obvious damage.
By checking at the fuses, the mechanic will start examining the various electrical parts of the car. He or she will take out the appropriate fuse for the tail lights to check if it is blown if they suspect a blown fuse. In such case, the mechanic will swap it out for a fuse that is properly rated for the amperage.
The mechanic should determine whether the unlit bulb is burned out if only one of the tail lights appears to be out. Bulb failure and replacement are inevitable over time. The mechanic will examine the unlit bulb’s filament to see if it is broken. In that case, a new bulb will be installed in lieu of the damaged one.
The mechanic will then examine the matching relay for the tail lights if it appears that the bulbs and fuses are in good operating order. The mechanic can measure the relay’s resistance using a multimeter. The mechanic will replace it and rewire it to the current connections if it is not operating properly.
The brake light switch should be checked by the mechanic if the tail lights appear to be operating OK but the brake lights are not. The mechanic will replace the old switch with a new one if the brake light switch is not reacting to the brake pedal. After that, the mechanic should ensure sure the brake lights are operational and responding to the new switch.
Any time a repair is required, the technician will see to it that all required work is done and that the new components work properly. A code reader/scanner will be used by the repair to erase any error codes that may have been set off by problems with the taillights.
Why won’t the brake lights on my 2012 Hyundai Sonata turn off?
Due to a problem with the brake pedal assembly that, in certain cases, prevents the brake lights from turning off, Hyundai is recalling 304,900 Sonata cars from the 2011 and 2012 model years.
The brake pedal stopper pad, which can eventually wear down and allow the brake light switch to stay on after the driver lifts their foot from the brake pedal, is at problem. In these circumstances, the Sonata is capable of continuing to drive while the brake lights are illuminated in the “braking” position, which can give other motorists the wrong impression. Additionally, this issue can make it possible to shift out of park without depressing the brake pedal. Even while Hyundai reports that the second issue hasn’t resulted in any accidents, it is this second issue that is more concerning.
The Hyundai Sonata automobiles produced from December 11, 2009, to June 30, 2011, are subject to the recall campaign.
On January 11, Hyundai will begin the recall procedure, and dealers will apply the repair. Owners may bring their cars in to have this problem addressed at no charge; the fix simply entails installing a new stopper pad.
Owners should reach Hyundai customer service directly at 1-855-671-3059 and reference recall number 136 prior to the start of the recall. They can also visit the National Highway Traffic Safety Administration (NHTSA) website at www.safercar.gov or dial the vehicle safety hotline at 1-888-327-4236.
Ramey, Jay
For his own personal use, Jay Ramey has been drawn to the more adventurous end of the reliability spectrum because he spent his childhood around really unusual European cars.
Are the brake lights on the Hyundai Sonata being recalled?
To find out if your vehicle is impacted by the Stop Lamp Switch Recall Campaign, enter your VIN.
Hyundai has made the decision to replace the stop lamp switches on various vehicles with model years 2007–2011 as part of a voluntary safety recall in the United States. Affected vehicles include the Accent, Elantra, Genesis Coupe, Santa Fe, Sonata, Tucson, and Veracruz. Hyundai notified the NHTSA of this action on March 29, 2013.
Where is the switch for the brake lights?
This switch, which is a component of the brake pedal assembly, can be found either under the dashboard or on the firewall next to the pedal lever’s top. One can easily be replaced.
By the end of the 1960s, automakers had switched to the more dependable mechanical brake light switch from the earlier hydraulic pressure in the brake line-driven system. Nowadays, a changeover rarely fails. The main power supply switch for the brake lights can now be operated by a lower-voltage control circuit thanks to the relay used in modern designs. A dependable switching mechanism with a long lifespan is produced by this setup.
Is AutoZone a brake light switch replacement shop?
Problems with the brake light switch or turn signals A replacement switch can be placed after checking the connection to the switch for corrosion or damage and buying it from your nearby AutoZone.
Why is the brake light on my car always on?
When the brake pedal is depressed, the brake lights, which are a component of the tail light, turn on. The most frequent reason for brake lights remaining on when the car is off is a faulty brake light switch or brake light switch stopper.
How do you tell if the switch for your brake lights is damaged?
You’ve checked the brake light fuse and the brake light bulbs, but the power to those areas is still not working. You should in this case examine the brake light switch. It is a device that joins and completes the electrical circuit for the brake lights in a car. It’s a relatively straightforward two-wire switch, with one wire controlling power coming in and the other controlling power leaving.
The switch, which is close to the brake pedal, is probably marked. Get your test light out once more, and ground it just like you did when you examined the fuses. Place the sensor on just one of the two wires while maintaining a firm grip on the brake pedal. Next, examine the other wire. The test lamps will light up if the switch is functioning properly and the power is connected. The brake light switch needs to be replaced if it doesn’t illuminate. Use the owner’s manual to find the major “power in” and “power out” lines if your switch has a more intricate design with more than two wires. Then, test those wires.
If you try all of these solutions and your brake lights still don’t function, there may be other systems in your car that require inspection. For instance, if your car’s turn signals and brake lights are wired together, you’ll need to check those systems’ fuses. Modern automobiles come equipped with an exclusive “brake light control module,” an integrated computer system, and onboard diagnostic scans to identify any issues.
Generally speaking, repairing a car’s brake lights is simple, but there are times when you should seek the advice of a qualified mechanic. It’s crucial to get those lights fixed as quickly as possible, whatever your car needs.
Can a defective brake light switch prevent a car from starting?
Vehicle Won’t Start Using the conventional keyed ignition, a broken brake light switch won’t prevent you from starting the vehicle. Driving a car with a push-button start, though, could get you into trouble. You might not be able to start the engine because you have to depress the brake pedal.
What model year of Hyundai Sonata is being recalled?
Certain Santa Fe and Sonata models from the model years 2021–2022, which feature 2.5L turbocharged engines, are being recalled by Hyundai Motor America (Hyundai). The pipe connection between the high-pressure fuel pump and fuel rail may leak fuel.
My brake light won’t work at AutoZone.
AutoZone will they replace brake lights? Although AutoZone doesn’t really provide brake light replacement services, our staff can help you with any inquiries you may have, aid you in locating the necessary supplies to get started, and perhaps even lend a hand.