Contact a locksmith, but be ready to re-bend your door. In order to access a tool inside and unlock your Hyundai Tucson, locksmiths will use a wedge and a pump up tool to lift the door away from the body.
A slim jim would work if you had a general manager, but you would also have to deal with the GM’s easy steal features.
Simply take the top of the door away from the body if you wish to DIY. As I said before, locksmiths will first use a plastic wedge to pull the door out a little at the top, and then they’ll use a pump-up wedge to open it further without harming the paint. If I were you, I’d use a 2×4 or similar wood wedge to prop open the top of the door, then sneak inside and deactivate the power door lock using a coat hanger. If you decide to do it, open the door on the side you wedged before opening the other to prevent any damage to the latch. Given that easy access is restricted by the Hyundai Tucson door’s top sill, you might even have better luck pressing the hatch release button.
I am a locksmith with AAA. There are three approaches you can take. As everyone has mentioned, the long rod (extension tool) can be used with the door wedge. It is much simpler to pull the handle back than the lock mechanism itself. You may also use this to open the handle if you have a tool that is designed to go inside the Hyundai Tucson and come up through the interior of the window. The handle only needs to be opened about 1/4 of the way before it unlocks. IL man, I wish I was there. Only an L-shaped tool (L tool), which is nearly impossible to find unless you’re lucky, will function inside the actual door. If you want to try the L, the internal door mechanism is about 6 inches below the handle, near to the back of the door. Once you’ve located the Bellcrank, you must fumble with it and then turn it clockwise. The hardest route is the last one.
Ask if lockout assistance is available by calling the local police non-emergency line.
What does your Hyundai Tucson lockout kit contain? Don’t even attempt it if it’s the slim-jim. If you don’t perform it correctly, you risk breaking the lock and being completely helpless.
If you have a wedge of some kind and the long metal bar (not a flat piece, that’s the slim-jim), you can drag the top of the door back and gain approximately an inch (enough room to get the bar through). Once the bar is in place, you can either attempt to push the manual lock or, if you have power locks, press the lock button. Another option is to try pulling the handle.
I’ve managed to lock my keys in the car six times this year, so I’m good at it. Asking the dealer where you purchased the Hyundai Tucson if they can produce you a key without the cip is a good idea. I keep the free one in my wallet because it is thin.
In This Article...
Use a long rod in Method #2.
Use a wooden wedge, air wedge, and a rod to unlock your automobile as long as you can at least partially push the top portion of the door open. First, take hold of the wooden wedge and insert it through the top of the door. Put a cover (ideally plastic) over the wedge to prevent damage to the paint.
To further distance the automobile from the door, slide the air wedge next to the wooden wedge and inflate it with air. Put as much pressure as you can on the wooden wedge to create a wide gap. Finally, carefully unlock your door using the locking mechanism on the side by inserting the rod through the door gap.
You could probably get by without one if you don’t have one. Even though it will be more difficult, the following video makes it seem simple.
How to bypass electric locks when approaching from outside
In some circumstances, it will be quicker and simpler to unlock the doors from outside. However, as the electrical wirings are frequently installed underneath the automobile door from the inside, this procedure is not advised for auto-lock doors or electric windows.
You’ll need to make a tool for this technique, ideally a hanger or a straight, long piece of metal with one end twisted into a hook.
Let’s now go on to using this technique to access an automobile without a key. To minimize the potential effect on the electrical wires, slide it down the bottom of the window glass through the automobile door, ideally the passenger side door. To make things simpler, you might need to peel aside the window’s black rubber weather stripping.
When you feel the key has been hooked, slowly slide the tool toward the lock and pull up.
Use the hook to unlock the door. You should slide the tool toward the lock and carefully pull up when you feel the key hook; the locking mechanism is typically immediately below the hatch. It might require several tries because certain locks need to be pulled downward rather than backward to the back of the car.
Is it possible to start my car without my keys?
- Obtain Your Extra Key.
- Open Your App.
- Use fishing line or string to open manual locks.
- Use a wire clothes hanger to unlock.
- Use an inflatable pump wedge to unlock.
- Use a Strip of Sturdy Plastic to unlock.
- Call a locksmith or AAA.
- Make a police call
Can Hyundai open my vehicle?
Users of the Hyundai Digital Key system can use their smartphones to start and unlock their cars. The new Digital Key, which takes the place of a physical key, may be downloaded via an app and used by up to four authorized individuals. Not only is this technology unique to Hyundai, but it is also largely new to the market. The most common inquiries about Hyundai Digital Key are addressed below.
Can an app be used to unlock a Hyundai?
The Hyundai Digital Key is operated through a phone app. The Google Play Store offers a free download of it for Android mobile devices. It is not yet accessible for iPhones. How times have changed: in the past, iPhones were the first to receive all the amazing apps.
However, Hyundai has made NFC Key Cards available for iPhone owners to use, so they are not totally excluded.
Without access to a key from the outside, how can you unlock a door?
It’s simple to open a door without a key by using a screwdriver. Find the one that fits your lock the best, then slide it into the little space between the door and frame just above the handle or knob. Simply place the tip of the screwdriver into the space between the bottom of the door and the floor while holding it in your right hand. Once you hear a click, turn counterclockwise. Repeat the clockwise turn until you hear a second click. Open the door at last.
How do you use a bobby pin to unlock a car door?
Yikes! Yes, it is possible to pick a car door lock, but doing so often requires considerable expertise and practice. One typical technique is to use a bobby pin.
The basic steps are as follows:
- Pick up a bobby pin, spread it out, and bend it into a V.
- Remove the rubber caps from the bobby pins’ two ends.
- Try to wiggle the lock into the open position by inserting both ends of the bobby pin and moving it up and down.
If you still have trouble, consider these more advice:
- Call a member of the family who has access to extra keys.
- Do you have access to roadside support? If so, make an aid request via the 800 number.
- Call a tow truck company or a locksmith.
We all make mistakes from time to time, like locking our keys in the car. But one error that you shouldn’t do is purchasing the incorrect expensive auto insurance. Why? because Jerry is there.
The quickest method to locate a vehicle insurance plan made specifically for you is through Jerry. Jerry will handle the rest after performing a thorough cross-analysis of the best prices offered by different providers. They all take care of the correspondence, documentation, and renewals for your best choice so you don’t have to. They can even assist you in canceling your old insurance!
How do you use a knife to open a car door?
It won’t take long to determine if the latch has to be shimmed and how to do it.
Take your knife, and place it exactly at the height of the doorknob, in the space between the door and the doorframe crack.
Find the latch by feeling around until you feel a chunk of metal sticking out of the door; it should feel springy.
Utilizing your knife as leverage, drive the lock into the door. The door will swing open if there isn’t another lock there.
Can I use my phone to unlock my car?
The Android user won’t need to remove their phone from their pocket to lock or unlock their car thanks to UWB technology. Customers with cars that use near-field communication (NFC) technology will be able to unlock their vehicles by touching their phones against the door.
Can a paperclip be used to open a car door lock?
So now you are aware of the tension wrench and rake lockpicking technique. This is a very helpful ability that will enable you to enter your home without the need to call a locksmith and will also enable you to assist others who have locked themselves out. It might even be necessary to pick the lock of a door if someone is trapped inside and in need of immediate assistance.
However, what should you do if you need to pick a lock but don’t have your lock picks with you?
You MacGyver yourself out of this tight hole using only paper clips and pliers, of course, by practicing the macho art of improvisation.
The process of picking a lock with paper clips is essentially the same as using a regular tension wrench and rake. Simply transform two paper clips into those exact same tools, then use them to pick the lock as you normally would.
How can you use a screwdriver to unlock a closed door?
You might be able to employ a technique called loiding, sometimes known as “shimming,” if there is enough space (or slop) between the door and the doorframe.
Although you might get away with anything bigger if the space between the doors is particularly large, you’ll probably need a thin flathead screwdriver.
Push the tip of your screwdriver between the door and the doorknob until you feel the spring latch in order to loid the lock with a screwdriver. Once the door begins to push open, keep pushing to retract the bolt.
A lock can a magnet unlock it?
Students are challenged to design something new in this assignment, which is a crucial step in the engineering process but one that could befuddle or frustrate them. The issues we encountered during our own testing are listed below, along with our fixes.
Paper won’t be punctured by brads: Students can have problems using the brad to rip a hole in the paper. If this occurs, make a tiny hole in the paper with a pointed pencil and insert the brad.
Things won’t spin on the brad: Probably a little hole. To make the hole bigger, turn the brad around completely a few times.
The lock doesn’t move because of the magnet: while every lock operates differently, friction is usually to blame for this issue. Make sure that any part of your lock that needs to move can do so without difficulty. It might not be able to be moved by your magnet if it is stuck too firmly.
The pieces keep bumping into each other:
- If the moving parts of your lock continually getting crooked, try rounding the edges.
- If a piece of paper is bending incorrectly and causing the lock to become stuck, you can stiffen the paper by folding it and securing it with stickers or paper clips.
- The 1-inch fold on the back can be attached to a clipboard or tucked under the edge of a thick book to help keep your wall from coming down.