- Even with a digital multimeter, never check the circuit resistance of an airbag component. If the circuit resistance is assessed with a tester, an unintentional airbag deployment may result in severe physical injury.
- Always unplug the negative battery terminal before beginning any work on the airbag system, and wait at least ten minutes.
This section will demonstrate how to use an airbag scanner for a Hyundai to read, delete, or clear the airbag lights. Airbag fault codes cannot be read by generic OBD2 scanners.
To accurately explain why the airbag light is on, the Airbag Module (SRS Control Unit) stores airbag system error codes.
- Under the dashboard, you may find the OBD-II port.
- Plug in the scanner on a Hyundai that can read airbag failure codes.
- Set position II of the ignition. Even when your Hyundai’s dashboard lights are all on, do not start it. The airbag light also illuminates and remains illuminated.
- Opt for Read Codes. The airbag control module will be contacted by the scanner, which will then collect the fault codes. You can see a code like B1620, which stands for internal airbag failure.
- Go back one level and choose Clear Codes if all the codes are in the Stored status. Clear the airbag trouble codes from your Hyundai control unit by following the on-screen instructions.
Keep in mind that specific codes cannot be removed if the issue that caused the airbag light to appear in the first place has not been resolved. In other words, you won’t be able to turn off the airbag light until you fix the issues if an internal fault code is active or a crash has been recorded.
To read and clear the airbag light on your Hyundai, you will want an OBD II diagnostic scanner. Many Hyundai owners attempt to reset the airbag light using a standard OBD-II code reader, however such scanners are unable to do so.
In This Article...
How to Reset a Hyundai’s Airbag Light
Using a portable pocket scanner, you may quickly reset the airbag light on your Hyundai from your house. These are also referred to as code readers or code removal devices. Make sure to purchase an OBD II code reader for your Hyundai rather than an OBD I code reader. Although these readers are reasonably priced, you may also have your local auto parts store scan your vehicle for free in order to read and clear the OBD computer’s codes.
Turn on and off your ignition.
When you experience the same problem, you should start by following this technique, which is identical to resetting the airbag light on a Toyota Camry. It needs timing the airbag light and has four straightforward stages that are simple to complete.
First, activate the ignition. Wait for the airbag light to turn on next; it typically illuminates for seven seconds before automatically turning off. After waiting three seconds, immediately flip the ignition switch off. Before starting the engine, go through the basic procedures a couple of times. Your car’s airbag light should illuminate for seven seconds before turning off permanently if everything is done correctly.
benvei
There is no doubt that you should check your airbag control module; something must have turned on that light. You might have harmed some of the yellow airbag wiring while installing your radio. I believe the airbag wiring to the passenger side airbag is located directly behind the radio.
With an OBD-II scanner that can examine the airbag module (not the $5 ones on eBay), you can reset the code. I don’t think it’s a smart idea to simply reset it without looking into what caused it. Personally, I wouldn’t interfere with the airbag system; instead, I’d let the dealer check it out to make sure everything is in order. OBD Scanners that can check ABS, Airbag, and other things are not cheap, so perhaps that is also the less expensive option.
ZoranB
Today when I started on the car, I noticed the airbag light was on a few minutes into my trip. I stopped, shut off the car, and then restarted it. The light turned on at the same time as the other warning lights, went off when they all went out, came back on a short while later, and stayed on. The vehicle has sat idle in my driveway. The only noteworthy event occurred yesterday night when I realized I had left one of the car’s windows open as I walked passed it. I also observed that my glovebox was open because I had earlier in the day taken something out of it but forgotten to close it. I just switched the ignition halfway before going to bed so I could use the batteries to close the window.
Anyone have ideas as to why this occurred and what I might be able to do to try to rectify it? If not, does anyone know if the warranty would cover this? I appreciate it.
How do I reset the airbag light on a 2013 Hyundai Elantra?
For the 2013 Hyundai Elantra, press the air bag reset button. You must carry out these easy steps. However, do not start the motor before turning the ignition key to the on position. As you wait, the air bag light should turn on in about 15 seconds. Turn the ignition to the off position as soon as the light turns on. Then, switch it back on when three seconds have passed. Follow these instructions three more times. On the final iteration, the air bag light should blink three times. Now the light is back on.
Turn the ignition key to the “on” position and wait for the airbag button to glow before switching off to reset the airbag light in your 2013 Hyundai Elantra. Wait three seconds after turning the key to the off position. Once you have completed these instructions twice, the airbag system in your car should be reset.
How can I turn off the airbag light?
The airbag light connects the seat belt system and the airbag system as part of the Supplement Restraint System (SRS) in automobiles (and vice-versa). When you turn on your automobile, the airbag light comes on for around seven seconds before going out, signifying that the internal system check was successful and finished. When the airbag light either never turns on or stays on while blinking, an issue exists. The airbag light needs to be reset at this stage.
Examining seat belt components, fixing bad clock springs, and replacing faulty sensors are a few techniques for turning off an airbag light. New bulbs or a fully charged battery are other options. While most repairs can be done without a professional, others may.
The following 10 steps will reset your airbag light:
- Turn on and off your ignition.
- Test drive your car when it has been restarted.
- Check the airbag switch for the passenger.
- Check to see if the seat belts are in place and functioning properly.
- Check to see if the passenger seat sensor is off.
- Use a scanner with the ability to reset the SRS or airbag light.
- Fix the broken airbag sensors.
- Replace or repair a broken clock spring.
- Check to see if the airbag is working properly.
- seek for a specialist’s help.
Although not exhaustive, the list above includes tried-and-true methods for tackling the problem. Some of them might not apply to your vehicle because compatibility is always based on the year, make, and model. It is recommended that you have your service manual on hand when carrying out any of these fixes. Always follow the manufacturer’s recommendations, too. Let’s get started on resetting your airbag light right away.
Do I turn on or off the passenger airbag light?
The Passenger Air Bag Off Light in the dash will illuminate if the passenger sensing system determines that no one is occupying the passenger front seat or if a number of other circumstances apply. You should understand what this means:
- Front passenger airbag is not deployed.
- You can also not have the passenger air bag deployed.
- In the event of a collision, the air bag will not deploy.
If there is an adult-sized passenger in the front seat and the Passenger Air Bag Off Light is on, this usually indicates that they are not seated properly.
Have the automobile inspected if the passenger adjusts their position and the light does not go out.
It might be necessary to shut off and restart the engine to get the light to turn off.
The informative nature of the aforementioned claims warrants independent verification. kindly visit our
What is the cost of turning off the airbag light?
Reset Airbag Light, at No. 1 Although it typically costs a few hundred dollars and takes several hours, depending on the type of automobile it might cost as much as $600.
What may make the airbag light continue to illuminate?
A problem with the seatbelts or airbags is indicated by the airbag light. Therefore, it’s usually not a good idea to drive when the airbag light is on. We advise having it towed to the dealership rather than driving it yourself if it remains illuminated in your car.
Where is the switch for the passenger airbag?
If the vehicle has a switch called the Passenger Airbag Cut Off Switch, it can be used to deactivate the passenger airbag (PACOS).
When the passenger door is open, you may access the switch for the passenger airbag on the passenger side of the instrument panel.
ALL FRONT-FACING PASSENGERS (CHILDREN AND ADULTS) CAN SIT SAFELY ON THE PASSENGER SEAT WHEN THE AIRBAG IS ACTIVATED.
Rear-facing child seats are safe for use on the passenger seat when the airbag is switched to OFF.
Can you reset the airbag light?
Without a scanner, most automobile models make it difficult to reset the airbag light. This is a safety warning since, when the airbag light appeared, you should always fix the problem. Fortunately, if you fix the issue, the airbag light will typically also turn off by itself in many automobile models.
However, in some older vehicles, the airbag light can be reset without a scanner by disconnecting the battery wires.
Make that there are no loose wires or rust in the connector plugs in the wiring system under the driver’s or passenger’s seat. Restart your car after spraying an electronic cleaner on the connecting plugs.
If you can’t detect any issues there, you should really invest in an OBD2 scanner or have a shop interpret the codes because otherwise you’ll have to guess what the issue is.
Is the airbag fuse removable?
The airbag cannot be turned off by removing a fuse; even if it had one, which it does not, doing so would not turn it off. Cutting or twisting the wires or changing the impedence won’t make it work either; after all, the equipment is fail-safe.
Does the airbag become turned off if the battery is disconnected?
- By putting the work clamp close to the weld, the current route is kept short.
- removing and isolating the cords from both batteries. First, disconnect the negative battery cable.
- separating the device from the car’s systems as much as you can.
- keeping cords away from sensors or computers.
- removing computers or other delicate electrical components before welding if the distance is closer than 300 mm ” (12″).
- applying a welding blanket to the vehicle’s windshield and other exposed surfaces.”
“Before or during the inspection of the airbags and other SRS components, it is crucial to take specific safety precautions. To avoid unintentional deployment, the restraint mechanism is disabled as part of these safety measures. Even if an airbag appears to have fully deployed, it may still be able to do so again. Commonly, the negative battery cable is disconnected and isolated in order to disable the restraint devices. In order for the system to totally discharge, time must also pass. For instructions on how to disable the restraint system properly, consult the vehicle-specific service literature. It can also be necessary to disable the SRS to safeguard certain sections when welding or performing other types of repairs.”