Usually found somewhere under the steering wheel, the reset button for the tire pressure monitoring system. Till the tire pressure monitor system light blinks three times, keep the reset button depressed. The sensors should reset about 20 minutes after you restart the vehicle.
In This Article...
How can I reset the Hyundai Santa Fe’s low tire pressure indicator?
Making sure that the tires on your Hyundai Santa Fe are inflated properly is the first step in resetting the tire pressure monitor system. The suggested tire pressure is 33 PSI for both the front and rear tires. Although 33 is optimum, you can go a little higher or lower without much difficulty. Once the tire pressure has been verified, you can just drive your car at 50 mph or greater for at least ten minutes. When you drive the car again, this should reset the sensor. Alternatively, you can turn the key to the ON position without starting the vehicle. Find the TPMS reset button, then press and hold it until you see the light blink three times. –
The Hyundai Santa Fe’s low tire pressure warning light can be reset by starting the vehicle and leaving it running for 20 minutes after pressing and holding down the TPMS Reset button until you see the light blink three times.
Tire Pressure Sensor Reset
Identify the TPMS system type.
If the direct system is employed by your 2019 Hyundai Santa Fe, resetting the tire pressure sensors might only require pressing a reset button on the dash or navigating a menu as described in your owner’s handbook. If your 2019 Hyundai Santa Fe has an indirect system, it must be reset by a dealer or one you have personally purchased using a magnet or scanning equipment. In order to reset some systems, the ignition must be turned on while the reset button is pressed and held down for three seconds within the glove box.
Pump up the tires.
Ensure that all tires are inflated appropriately. All tires must be fully inflated because you are resetting the sensors to “zero,” or else the sensors won’t be properly calibrated and their readings will be off.
Evaluate the battery.
If the sensor in your 2019 Hyundai Santa Fe is powered by a battery, make sure it is not dead. The battery should be changed every five years. Since the battery is integrated, in certain cases this necessitates replacing the complete sensor unit.
Make the transponders new.
Every wheel has a unique transponder. Each responder’s location changes when the wheels are rotated, and the TPMS needs to learn their new locations. Although this relearning process varies depending on the vehicle, you can get more information in the TPMS chart in your manual or online. If the valve stems double as tire pressure sensors, it is a good idea to swap them out when purchasing new tires.
Apply the magnet technique.
Press the lock and unlock buttons on the key fob when the key is in the ignition but the engine is not running. Placing a magnet over each valve stem after the initial chirp will cause the horn to chip for each valve in the following order: left front, right front, right rear, and left rear. Make that the driver information center is showing the pressure values.
Utilize the scan tool approach.
The owner’s manual’s TPMS Reprogramming Procedure menu prompts can be followed if no sensors are being replaced.
What is the Hyundai Santa Fe’s TPMS?
Hyundai vehicles are equipped with TPMS, or tire pressure monitoring systems, which may detect low tire pressure in any of the car’s four tires and issue an alert. According to the table below, a TPMS from one of two manufacturers is installed as a component of the valve assembly in every Hyundai vehicle.
According to the table below, a TPMS from one of two manufacturers is installed as a component of the valve assembly in every Hyundai vehicle. The tire pressure monitor ECU/receiver receives the data from the sensor, which detects the pressure and temperature inside the tire, together with the TPMS’s distinctive ID.
If the TPMS ID is stored with the ECU, the placard pressure is checked with it, and if there is a pressure difference, a warning light is illuminated on the dash-mounted display.
Without a reset button, how do you reset a TPMS?
How to Reset the Tire Pressure Light Try the following if your TPMS light is still on after you have inflated your tires to the recommended pressure: 10 minutes at a speed of 50 mph would be plenty. When you start the car again, the TPMS light should not be on because the tire sensors should have been reset.
How can the TPMS light on a 2019 Hyundai Elantra be reset?
You may reset the tire-pressure monitoring system in your Hyundai Elantra once you’ve found the TPMS.
The following steps will show you how to reset the TPMS on a Hyundai Elantra:
1. Turn the ignition to the “ON” position and insert the key.
2. Avoid starting the car.
3. Hold down the TPMS reset button while waiting for the tire pressure light to blink three times.
4. Let go of the TPMS button.
5. Start the vehicle.
6. Permit the sensor to reset for 20 minutes.
Your tire-pressure monitoring system will be reset by following these instructions. After putting air in your tires, it’s crucial to reset your TPMS since it keeps your knowledge of your tire pressure accurate. When your tires need to be inflated, the tire pressure monitoring system will let you know by turning on the tire pressure light.
How can I turn my TPMS light back on?
When the tire pressure light blinks three times, release pressure on the TPMS reset button. Start the car, then wait for the sensor to refresh for around 20 minutes. Under the steering wheel is where you’ll locate the reset button for the tire pressure monitor. If you can’t find it, consult the owner’s manual for your vehicle.
Has the 2020 Santa Fe got TPMS?
We will examine the most popular 2019 cars, SUVs, minivans, and trucks during the coming months. We’ll concentrate on the top-selling SUVs in the US in 2019 during the month of April.
All American-made automobiles must have direct or indirect TPMS systems fitted as of 2008 as a result of the TREAD Act’s 2007 mandate.
The direct TPMS system is used in the production of the Hyundai Santa Fe. If one or more tires on a direct TPMS system indicate low tire pressure, the TPMS sensors will communicate this information to the vehicle’s ECU. Each tire pressure or an indicator light (low-line TPMS system) will be displayed on the dashboard (high-line TPMS system).
Should the TPMS be reset after purchasing new tires?
After changing or rotating your tires, or after adding new sensors, you should always reset your TPMS. Even after you have inflated your tires, some sensor manufacturers advise restarting the device. By teaching the primary TPMS system to identify the sensors in their new locations, resetting the TPMS is frequently referred to as retraining the system. TPMS reset procedures vary from vehicle to vehicle and typically involve a specific sequence of ignition and pedal actions, a configuration change in your dashboard menu, or the use of a TPMS Reset Tool.
Does programming of Hyundai TPMS sensors are required?
Before being inserted in the tire, these sensors need to be programmed with the appropriate protocol/application information for the vehicle, and they then need to be retrained to the vehicle.
On a Santa Fe 2022, how do you reset the tire pressure light?
- Drive the vehicle for around 10 minutes at 50 mph.
- Turn the ignition key to the “On” position without starting the automobile.
- After three seconds, or when the light has flashed three times, let go of the TPMS reset button.
- To reset and calibrate the sensor, start the engine and let the vehicle run for 20 minutes.
The reset button for the tire pressure monitor is often located under the steering wheel on Hyundai Santa Fe vehicles.
You could also wonder why the tyre pressure indicator is still on after the tires have been inflated. If your tire pressure monitoring system is malfunctioning or there is a persistent leak, the air pressure warning light may continue to glow even after you have inflated your tires.
Use a pressure gauge to confirm that the tire is properly inflated to the recommended air pressure if the TPMS warning light comes on again after you’ve inflated it.
My TPMS light won’t turn off; why?
When the TPMS warning light illuminates, proceed with caution. This indicates that at least one of your tires may be at least 25% under-inflated.
*The simplest way to get the most accurate reading is to check the tire pressure before you drive on it when the tire is “cool.” If your TPMS light is on, first check that you have correctly reset your TPMS by following these instructions.
Will my TPMS light automatically turn off if I fill my tires with air after it illuminates?
Several minutes after reinflating the tires to the prescribed pressure, the TPMS light ought to go out.
What happens if I adjust the tire pressure but the light on my tire pressure gauge still doesn’t go out?
The only place that can fix a computer issue that causes the TPMS warning light to turn ON and flash ON for one second and OFF for three seconds is the dealership service center. When the TPMS warning light illuminates and remains on, one or more tires may have low tire pressure. The light ought to go out once the tire is inflated to the recommended tire pressure listed on the door placard. Always check the pressure in all of your tires because one or more of them may not be at the proper pressure.
What does the phrase “check TPM system” mean?
The TPMS (Tire Pressure Monitoring System) is designed to notify you when a tire’s pressure is too low and may result in hazardous driving situations. If the indicator is on, your tires may not be properly inflated, which might result in premature tire wear and even tire failure. It’s critical to comprehend the value of appropriate tire inflation and how TPMS can prevent a potentially hazardous situation.
Both excessive and inadequate tire inflation can result in early tread deterioration and potential tire failure. Increased traction, early wear, and an inability to withstand impact from the road can all be effects of overinflation. The middle of the tread on tires with excessive air pressure may prematurely wear out. Underinflation, on the other hand, results in slow tire reaction, lower fuel economy, excessive heat buildup, and tire overload. The shoulders or tread edges of a tire that is underinflated will prematurely wear out on both sides.
Finding the TPMS indicator on your dashboard is straightforward if this is your first time hearing about tire pressure sensors. It is a light that has a horseshoe form with an exclamation point in the middle.
In what location is the TPMS sensor?
Where is the location of the tire pressure sensor? It is affixed to the interior of the rim from inside the tire. The tire pressure sensor is a little cylinder that you can see if you take the tire off the rim.
Can I drive with my TPMS on?
To avoid seeming like Debbie Downer, we’ll simply say no. Driving around with your TPMS light on is not safe. You can’t tell how quickly your tire is losing air or how long it has been over- or underinflated without doing a tire examination. The best course of action is to check the current inflation level of each tire with a tire pressure gauge.
When the tire inspection light appears while you are driving, slow down and get to the closest gas station or service facility.
Why are my tires fine but my TPMS light is on?
It’s likely that one or more of your tires have low air pressure if you see the tire pressure indicator turn on. However, even if your tires are in good condition, there are a number of things that could cause the sensors to go off, so you shouldn’t rely only on the data from the tire pressure monitoring system of your car.