The 2017 Hyundai Elantra’s TPMS can be easily reset. Make sure the car is on level, flat ground first. Verify that the tire pressure is within the proper psi range for each tire. The psiAmount should be stamped on the tire’s side if you look there. You’ll want to get in the car after this is finished and switch on the power, but do not start the engine. A button with the label “tpms” or something similar is located to the right of the steering wheel. When it starts to blink, hit it and keep it down. Once it blinks, let the car sit for roughly 20 minutes so that it can readjust. You can switch off the car and then turn it back on when the light stops blinking to be sure the reset was successful.
Can someone kindly explain me how to reset the TPMS as we all know that the 2017 model does not have a TPMS button?
I just looked beneath the steering wheel of my girlfriend’s car, and there is no TPMS button. I did notice a yellow switch after removing the fuse box cover, but I refrained from touching it.
Press the tpms reset button on a 2017 Hyundai Elantra, hold it down until the light flashes three times, and then let go. Turn on the engine and give the sensor 20 minutes to run. Usually, the tire pressure control reset button is located under the steering wheel.
My 2017 Hyundai Elantra lacks a reset button, but the owner’s manual describes an optional tire pressure monitoring system; mine only has a general warning light. A reset button might be present on the pricier model but not on the more basic one like mine.
In This Article...
How Do You Reset A Hyundai Elantra’s TPMS?
You may reset the tire-pressure monitoring system in your Hyundai Elantra once you’ve found the TPMS.
The following steps will show you how to reset the TPMS on a Hyundai Elantra:
1. Turn the ignition to the “ON” position and insert the key.
2. Avoid starting the car.
3. Hold down the TPMS reset button while waiting for the tire pressure light to blink three times.
4. Let go of the TPMS button.
5. Start the vehicle.
6. Permit the sensor to reset for 20 minutes.
Your tire-pressure monitoring system will be reset by following these instructions. After putting air in your tires, it’s crucial to reset your TPMS since it keeps your knowledge of your tire pressure accurate. When your tires need to be inflated, the tire pressure monitoring system will let you know by turning on the tire pressure light.
2009–2017 TPMS Tip Featured Elantra, Elantra Coupe, and Elantra Touring from Hyundai
Mitchell 1 contributes TPMS knowledge to Modern Tire Dealer, a highly regarded journal that produces editorial content targeted at independent tire dealers. This story is being shared on our blog along with a link to the Modern Tire Dealer website, where you may read it in its entirety. The TPMS information in this page can also be found in our ProDemand(r) auto repair information software’s reset procedures tab, along with other crucial reset procedure information for the chosen car.
NEED FOR SPECIAL TOOLS? Yes, a TPMS module on a Hyundai GDS (Global Diagnostic System).
The 2011–2017 Hyundai Elantra, 2014 Elantra Coupe, and 2009–2012 Elantra Touring all have tire pressure monitoring systems (TPMS) that use wheel-mounted tire pressure sensors to keep track of the air pressure in the four road tires. The system accomplishes this by using a receiver, four radio frequency (RF) tire pressure sensors, two warning lights on the instrument panel, and a data circuit.
The low pressure warning light on the instrument cluster will turn on if tire pressure falls below the permitted threshold or if a quick leak is discovered. The TPMS warning indication will be illuminated if the system discovers a fault with the receiver or sensor, or if it discovers a defect that is external to the receiver or sensor. The light will remain on during the whole ignition cycle if the issue is deemed “important.”
There are two operating modes for the tire pressure sensor: stationary/rolling mode and sleep mode. The sensor will record temperature and pressure every four seconds while measuring acceleration every 60 seconds in the stationary/rolling mode. To save battery life, the sensor enters a low current consumption state during sleep mode and stops taking measurements. When new, all sensors are in this condition. The sensor won’t communicate unless the commence command asks it to or the speed of the car reaches 20 mph (32 km/h).
All tires must have their air pressure checked and changed to the specified cold pressure mentioned on the vehicle certification label (located on the driver’s door or door pillar) when the low tire pressure warning light illuminates. Repair the tire as necessary if it has been damaged. Make sure the alarm light is turned off. Check the tire pressure again if the warning light remains on. Turn the wheel a quarter turn and wait another four minutes if the tire pressure is satisfactory. There is a TPMS issue if the Hyundai Elantra tire pressure light is still on or the TPMS warning indicator is lighted.
NOTE: It must be started if the tire pressure sensor is replaced. Rotation of the wheels and tires has no impact on the TPMS. Check the air pressure in each tire and make any necessary adjustments when the low tire pressure warning light illuminates.
Why, after filling the tires, does my tire pressure light remain on in a Hyundai?
If you’ve inflated your tires, but the air pressure warning light continues to flash, your tire pressure monitoring system is malfunctioning or you have a gradual leak. A bright TPMS warning light indicates a problem with a tire pressure sensor, assuming there isn’t a leak in your tire. One of them might be damaged, the lithium-ion battery might be dead, or the TPMS itself might have an internal problem. You’ll need to get your Tire Pressure Monitoring System repaired in any of these scenarios.
Quick Tip: Recheck the tire to ensure it is inflated to the correct air pressure if the TPMS warning light illuminates again after you have inflated it. Low tire pressure indicates an air leak, which requires repair or tire replacement.
How can I turn off the tire pressure warning light?
When the tire pressure light blinks three times, release pressure on the TPMS reset button. Start the car and let it run for 20 minutes to let the sensor reset. Under the steering wheel is normally where you’ll find the reset button for the tire pressure monitor. If you can’t find it, consult the owner’s manual for your vehicle.
Why is the pressure in my tires light still on?
When the TPMS warning light illuminates, proceed with caution. This indicates that at least one of your tires may be at least 25% under-inflated.
*The simplest way to get the most accurate reading is to check the tire pressure before you drive on it when the tire is “cool.” If your TPMS light is on, first check that you have correctly reset your TPMS by following these instructions.
Will my TPMS light automatically turn off if I fill my tires with air after it illuminates?
Several minutes after reinflating the tires to the prescribed pressure, the TPMS light ought to go out.
What happens if I adjust the tire pressure but the light on my tire pressure gauge still doesn’t go out?
The only place that can fix a computer issue that causes the TPMS warning light to turn ON and flash ON for one second and OFF for three seconds is the dealership service center. When the TPMS warning light illuminates and remains on, one or more tires may have low tire pressure. The light ought to go out once the tire is inflated to the recommended tire pressure listed on the door placard. Always check the pressure in all of your tires because one or more of them may not be at the proper pressure.
Why won’t the tire pressure warning light come on?
Try the following if your TPMS light is still on after you have inflated your tires to the recommended pressure: 10 minutes at a speed of 50 mph would be plenty. When you start the car again, the TPMS light should not be on because the tire sensors should have been reset.
My tires are in good condition, so why is my low tire pressure sign on?
While the tires appear to be in good condition and the low tire pressure light is ON, you can:
- simply press a button to reset the machine and observe the results; or
- The sensors need to be changed since one or more of them are damaged.
After starting the vehicle, the low tire pressure warning light ought to turn on for a few seconds. The light ought to be turned off right away.
Drive your car, preferably to the closest gas station or tire shop, to check the air pressure in each tire if the low tire pressure warning light is still on.
Typically, a tire with an air pressure that is 10% to 15% low will turn on the warning light. The air pressure inside the tires also tends to drop in cold or icy conditions. Short trips in the car will warm up the tires and raise the pressure in them.
But if the low tire pressure warning light is still on and all the tires are adequately inflated and warmed up, move on to the next step.
Take this opportunity to get out the owner’s manual. The TPMS reset button may be found on the console or in the glove box, depending on the make and model of your car.
Here are the steps to take after finding the TPMS reset button:
- Don’t start the engine after turning the key to the ON position.
- For at least three seconds, press and hold the TPMS reset button before letting go. The system will switch off the warning light and produce a beep or other audible alert.
- To finish the reset process, start the engine and drive the vehicle for 30 to 1 hour at a minimum speed of 19 mph.
- It’s time to check or replace the TPMs sensors if the warning light comes back on.
- To get the system tested, drive to the nearest tire store or dealership.
If your car has TPMS, avoid making it a practice of resetting it every time the low tire pressure warning light comes on.
Your safety is considered during the system’s design. The pace of technological advancement means that the TPMS sensors get better with each new model. However, you should make it a practice to check the tire pressure each time you get in the car in order to get the most out of what you have.
Use a different method than the TPMS to check the tire pressure. A quick visual check is sufficient to establish the existence of a flat.
Here’s a helpful hint: just in case, always have a tiny tire pressure gauge in the glove box. You may check the real tire pressure with this straightforward gadget before the TPMS activates.
Take your vehicle to the shop so they can “re-learn” the sensor with a specific tool if your TPMS light is still on. These tools are available online, but they are not inexpensive. I would advise researching the Autel TS501.