- Even with a digital multimeter, never check the circuit resistance of an airbag component. Accidental airbag activation can cause serious physical injury if the circuit resistance is measured using a tester.
- Always unplug the negative battery terminal before beginning any work on the airbag system, and wait at least ten minutes.
This section will demonstrate how to use an airbag scanner for a Hyundai to read, delete, or clear the airbag lights. Airbag fault codes cannot be read by generic OBD2 scanners.
To accurately explain why the airbag light is on, the Airbag Module (SRS Control Unit) stores airbag system error codes.
- Under the dashboard, you may find the OBD-II port.
- Plug in the scanner on a Hyundai that can read airbag failure codes.
- Set position II of the ignition. Even when your Hyundai’s dashboard lights are all on, do not start it. The airbag light also illuminates and remains illuminated.
- Opt for Read Codes. The airbag control module will be contacted by the scanner, which will then collect the fault codes. You can see a code like B1620, which stands for internal airbag failure.
- Go back one level and choose Clear Codes if all the codes are in the Stored status. Clear the airbag trouble codes from your Hyundai control unit by following the on-screen instructions.
It should be noted that some codes cannot be removed if the issue that initially caused the airbag light has not been resolved. In other words, you won’t be able to turn off the airbag light until you fix the issues if an internal fault code is active or if a crash is recorded.
You’ll need an OBD II diagnostic scanner to read and clear the airbag light on your Hyundai and to extract airbag codes. Many Hyundai owners attempt to reset the airbag light using a standard OBD-II code reader, however such scanners are unable to do so.
In This Article...
Turn on and off your ignition.
When you experience the same problem, you should start by following this technique, which is identical to resetting the airbag light on a Toyota Camry. It needs timing the airbag light and has four straightforward stages that are simple to complete.
First, activate the ignition. Wait for the airbag light to turn on next; it typically illuminates for seven seconds before automatically turning off. After waiting three seconds, immediately flip the ignition switch off. Before starting the engine, go through the basic procedures a couple of times. Your car’s airbag light should illuminate for seven seconds before turning off permanently if everything is done correctly.
How Can the Airbag Light Be Reset? (5 Steps) Whether Scanner Is Used
Your life may one day be saved by an airbag if an accident occurs. It’s time to turn the airbag light back on if you repaired the airbag system. Here’s how to go about it.
Do you want to know how to reset your airbag light after it appeared on your dashboard?
When certain dashboard lights come on, like the engine or airbag lights, you should pay close attention—the airbag light in particular is crucial for your safety.
When the light is on, the airbag will not deploy as it is intended to do whenever there is a collision.
benvei
There is no doubt that you should check your airbag control module; something must have turned on that light. You might have harmed some of the yellow airbag wiring while installing your radio. I believe the airbag wiring to the passenger side airbag is located directly behind the radio.
With an OBD-II scanner that can examine the airbag module (not the $5 ones on eBay), you can reset the code. I don’t think it’s a smart idea to simply reset it without looking into what caused it. Personally, I wouldn’t interfere with the airbag system; instead, I’d let the dealer check it out to make sure everything is in order. OBD Scanners that can check ABS, Airbag, and other things are not cheap, so perhaps that is also the less expensive option.
Airbag Light Stays On in a Hyundai Tucson: Diagnosis
The computer system in your Hyundai Tucson performs a self-diagnostic check on all essential systems each time you turn it on. A diagnostic warning light for the associated system will appear on the dashboard if any of these checks are unsuccessful. The airbag light will come on if the airbag system fails this test.
You might see something along the lines of SRS, a picture of a human with the airbag deployed, or the term airbag, depending on the model year and the nation you happen to be in. Consider each of these to be an airbag light.
The airbag light on your Tucson is there to alert you to an issue with the airbag system. It is perfectly normal and a standard part of the diagnostic cycle if it turns on briefly as the car begins. When it stays on, though, there might be an issue.
How do I reset the airbag light on a 2013 Hyundai Elantra?
For the 2013 Hyundai Elantra, press the air bag reset button. You must carry out these easy steps. However, do not start the motor before turning the ignition key to the on position. As you wait, the air bag light should turn on in about 15 seconds. Turn the ignition to the off position as soon as the light turns on. Then, switch it back on when three seconds have passed. Follow these instructions three more times. On the final iteration, the air bag light should blink three times. Now the light is back on.
Turn the ignition key to the “on” position and wait for the airbag button to glow before switching off to reset the airbag light in your 2013 Hyundai Elantra. Wait three seconds after turning the key to the off position. Once you have completed these instructions twice, the airbag system in your car should be reset.
Is a reset of the airbag light necessary?
The airbag warning light could come on as a result of a sensor malfunction or accidental travel. It will be necessary to reset the system and examine the sensors. The purpose of the airbag clock spring is to preserve continuity between the vehicle’s electrical wiring and the driver-side airbag.
Can my airbag be reset?
After receiving your repaired module from us, you won’t need to take it to the dealership for additional programming because we reset all fault codes.
Except for modules that were harmed by a flood, fire, or another type of hardware damage, all airbag control modules can be reset and reprogrammed.
Accident-related hard and soft codes are stored in airbag control modules. The module that activates the airbag light will keep error codes even after minor incidents. To turn off the airbag light, we reset and erase all of these crash codes from the computer module.
What is the cost of turning off an airbag light?
Reset Airbag Light, at No. 1 Although it typically costs a few hundred dollars and takes several hours, depending on the type of automobile it might cost as much as $600.
How can I check the code on my airbag light?
Diagnostic Codes for Airbags The airbag codes consist of two digits. To read the codes, count the flashes the light makes, then count them again after the pause. For instance, two flashes, a pause, and four flashes indicate a code 24 issue with your airbag system.
With OBD2, can the airbag light be reset?
It’s time to reset the engine light when you have completely installed the new parts and are confident that everything is installed correctly. There is no other way to accomplish this; you must use an OBD2 scanner. Make that the airbag light is reset and that it no longer appears on the dashboard. Reread the codes and look for any trouble codes if the problem is still there.
What could turn on the passenger airbag light?
The spring is intended to preserve continuity between the wiring and the driver’s airbag and coils throughout your steering wheel. The spring may wear out and fail over time, turning on the airbag warning light. Older autos are more likely to have this flaw.
The important line is that you must stop driving as soon as your airbag light illuminates and have your automobile inspected by a repair as soon as possible. Your airbags won’t activate until the issue is identified and remedied. Never disregard your airbag light since your safety and the safety of your passengers are top priorities.
Dashboard Warning Lights Explained, which offers guidance on a variety of lights and their meanings, is a good resource if you want to learn what additional warning lights represent and what to do when they illuminate.
What does it imply if the airbag light is on indefinitely?
A problem with the seatbelts or airbags is indicated by the airbag light. Therefore, it’s usually not a good idea to drive when the airbag light is on. We advise having it towed to the dealership rather than driving it yourself if it remains illuminated in your car.
Where is the switch for the passenger airbag?
If the vehicle has a switch called the Passenger Airbag Cut Off Switch, it can be used to deactivate the passenger airbag (PACOS).
When the passenger door is open, you may access the switch for the passenger airbag on the passenger side of the instrument panel.
ALL FRONT-FACING PASSENGERS (CHILDREN AND ADULTS) CAN SIT SAFELY ON THE PASSENGER SEAT WHEN THE AIRBAG IS ACTIVATED.
Rear-facing child seats are safe for use on the passenger seat when the airbag is switched to OFF.
Driving with the airbag light on is it forbidden?
In some vehicles, it is even possible to turn off the passenger airbags, which will make your dashboard’s airbag light come on.
You should only deactivate the passenger airbag when absolutely necessary because, as was previously said, airbags are an essential safety element.
If your airbag light ever illuminates for no apparent reason, you should try to resolve the situation.
Can a blown fuse turn on the airbag light?
Only if the blown fuse is directly connected to the airbag system may it cause the airbag light to turn on and off. Although this is the primary reason for this light, other problems can cause an airbag light to suddenly come on.
The airbag system can malfunction, you can interfere with the seat belt sensor, there is a broken clock spring, there is damaged cabling under the seat, the computer system receives incorrect data, or the sensor was damaged in an accident, which can cause the light to turn on and off.
What is the price of replacing an airbag sensor?
Depending on the automobile model and labor charges, the cost to replace an airbag sensor ranges from $100 to $600. A sensor for an airbag costs between $50 and $300, as does the labor.
Both the airbag sensor and its replacement are delicate parts. Even for an expert, correctly diagnosing and installing the airbag sensor can take up to two hours.
The airbag sensor itself is typically not very expensive; you may anticipate paying between $50 and $300 for a brand-new one. Avoid taking the chance by always purchasing OEM original, genuine products and never aftermarket sensors.
You can save money by replacing the airbag sensor yourself if you are highly confident working on cars and meticulously following the repair manual.
If you have even the least qualms regarding the replacement, have a pro handle it.
Keep in mind that it is a crucial component, therefore installing it properly is important in case of an accident. Additionally, if you make a mistake, there is a chance that all of the airbags in the automobile would deploy, costing thousands of dollars to repair.