One of the last things you want in the winter when navigating through wet, slushy roadways is to be unable to wipe your windshield clean so you can see properly. In order for the wipers to effectively remove the slushy debris from the windshield, a malfunctioning windshield washer pump must be replaced as soon as possible. Many car owners can complete this task by themselves in 30 minutes or less. Here’s how to change the windshield washer pump on a Hyundai Elantra from 2001 to 2006.
Under the left front headlight is where you’ll find the windshield washer pump. To get to the pump, you have to take the headlight off. To keep the car’s hood up, open the hood and insert the lift support stick into the hood’s slot.
Inside the engine compartment, the headlights are secured by two 10mm bolts at the top and one at the bottom. Using a 10mm socket and ratchet, remove the bolts. To remove the bolt at the bottom of the headlamp, you will need a ratchet extension of at least 5″. The back of the headlight is wired with two different sets of wires. The wires attached to the headlamp are released from their clips and are then taken out.
To remove the headlight from the car, pull out the left side of the assembly first, then the right side.
To capture the windshield washing fluid that will spill out when you remove the pump from its housing, place a clean, grease- and oil-free catch basin beneath the pump.
After removing the headlamp, you will be able to see the pump’s hose. To locate the pump, descend with the hose into the area that the headlight formerly occupied. Take the pump’s power connector off by pulling it.
While tugging on the pump, wiggle it back and forth to free it from the housing. The pump will immediately emerge. Using a tiny flathead screwdriver, pry the hose attached to the pump’s nipple off.
Place the new pump back into the housing after attaching the hose to its nipple. Connect the pump’s power connector. Put the headlamp back on and secure it with a bolt. Pour the windshield washer solution from the catch basin into the reservoir for the windshield washers.
Once the engine is running, lift the washer fluid lever to spray it onto the windshield. Before the fluid sprays out onto your windshield, the pump may need to refill the hose with fluid for a short while. Once the washer fluid has covered the windshield, you are finished.
Contact a specialist, like Wolfe’s Foreign Auto, if you don’t want to handle this on your own.
In This Article...
bdh
“My pump was changed this summer. The bumper cover is retained unless you need to replace the reservoir, which is unlikely to be necessary. Remove the wheel. As mentioned in the first response, the wheel tub can be removed. After that, push the plastic aside to reveal the pump. When you remove the pump, you can become little wet since the reservoir will drain. Make sure you obtain the correct pump because I’m presuming you have a rear washer. I purchased my Hyundai OEM component from eBay, and installation required only unplugging the electrical, wriggling the old part out of the reservoir, and unplugging the two hoses. The two little pipes that feed the front and rear should not be turned around.
At first, I believed that my nozzles were clogged. After using thin wires to probe the sprayers and air flushes, I gave up and purchased the pump. worked perfectly.
If you are ready, this task will take you a half-hour. Spray the mud or other substance out of the wheel well first, away from where you are working.”
You do need to be aware of whether you have the proper pump. You will have two outlets on the pump if you have a rear window washer. The wheel tub may have a fastener that needs to be removed, but it shouldn’t be too difficult. The pump is situated behind the wheel tub’s front end. Don’t be afraid of electricity; just unhook the pump by pulling a wire from the plug. There is a wiggle and pull required since the pump is “plugged” into the fluid reservoir. Be ready for drainage from the sizable hole you just made in the washer fluid tank’s bottom. If you are concerned, mark the hoses so they are attached correctly. The best option is to capture images with your phone.
One of the easiest remedies, this is also straightforward to carry out. But as was mentioned before, if you are unable to change a tire, hire someone to do it for you.
Why the windshield washer on a Hyundai Elantra isn’t working and how to fix it
Driving visibility is always assured by a working windshield washer. When you turn on the washer in your Hyundai Elantra, no fluid should flow out of the nozzles. There may be a number of reasons for this. In this post, we describe what these are and what you may do to address them.
The most frequent issues that prevent the Hyundai Elantra’s windshield washer system from operating normally include blocked spray nozzles, leaking hoses, blown fuses, failed pumps, frozen fluid, and electrical system issues.
What location is the windshield washer pump?
The windshield washer pump and a small electric motor are packaged together in contemporary autos. The windshield washer pump is often mounted in the tank’s lower section (bottle).
The windshield washer fluid tank’s bottom holds the windshield washer pump (motor).
As seen in the figure, the windshield washer tank is often found in front of one of the front wheels, behind the front bumper.
How it works: When you turn on the washer using the switch, the control module (like the BCM) receives a signal. The control module uses the relay to turn on the windshield washer pump. Through the hoses that are attached to the washer jets, the pump pumps windshield washer fluid.
What is the price of a windshield washer pump?
Best in Automotive Repair Replacement windshield washer pumps typically cost between $124 and $167. The cost of labor is expected to be between $75 and $95 while the cost of parts is between $49 and $72. This range does not account for taxes and fees, your particular car, or your particular location.
How much does a washer pump replacement cost?
A new washing machine pump costs between $25 and $40 on its own, excluding labor. Repair costs for professionals range from $200 to $450.
How do I get the windshield wiper fluid to start flowing again?
With the aid of a pin, unclog the clogged windshield washer nozzle. Then, blow the debris back through the hose with compressed air.
- If the pump is running but no fluid is coming out, your windshield washer nozzles are probably clogged.
- A spherical one-way check valve or a plastic barbed connector can be found somewhere along the path. Retry the washer after cutting the tubing there.
- You may tell the nozzles are clogged if fluid squirts out. Push a tiny pin into the nozzles to remove any debris, then blow the obstruction back down the line and out the end you disconnected.
How can I tell if the wiper fluid pump is malfunctioning?
When you activate the windshield washer fluid to spray over your windshield, the washer pump emits a characteristic sound. When you press the button, if no sound is made and no fluid sprays over your windshield, the pump is either damaged or isn’t getting electricity. If this is the situation, make sure the fuse that powers the washer pump isn’t burned out and replace it if it is. To replace the windshield washer pump, though, you’ll need to get in touch with a nearby ASE-certified mechanic if the fuse is not the issue.
What is the cost of repairing a washer that won’t spin?
Cannot Spin During the spin cycle, a lot of the frequent problems with washing machines pop up. The washer’s ability to spin out can be hindered by an agitator issue or a damaged pump. You will spend between $150 and $500 to fix any parts that are preventing your washer from going through its normal cycles.
Why is the wiper fluid leaking from my windshield?
Older automobiles with the windshield washer reservoir located close to the exhaust system may have cracking and leakage over time due to the intense heat. However, owners or techs filling the machine with water rather than pure washer fluid is the most frequent reason for a fractured reservoir. When it is below freezing outside, the water inside the reservoir will freeze, hardening and eventually cracking the plastic when it thaws. The washer reservoir will eventually run dry as a result of the fluid leaking from it.
The washer pump may, and frequently does, become burned out if you attempt to switch it on with the tank empty. In this case, you will also need to replace the washer. To prevent this potential issue, it’s crucial to constantly fill the windshield washer reservoir exclusively with washer fluid.
How much does repairing a wiper motor cost?
This pricing range excludes any additional fees or taxes and is based on the national average for all automobiles, regardless of make or model. Repairs or maintenance expenses like changing the wiper blades or topping off the windshield wiper fluid are subject to additional fees.
Does the motor for the windshield wipers have a fuse?
You will likely suffer a blown wiper fuse, which is intended to happen before the wiper motor fails. The wiper motor is protected by the fuse, which is intended to be the circuit’s weak link. In essence, the fuse will blow if the wiper motor in your car is overworked to prevent harm to the motor.
Does repairing a washer make sense?
Your washing machine may occasionally experience costly malfunctions, and even after repairs, some parts may continue to function poorly. Additionally, hiring a professional technician to make the repairs could be expensive. Once more, if the entire cost of repair exceeds 50% of the price of a new unit, you should replace the washing machine.
When you want to fix or replace a washing machine, it is a good idea to verify your warranty. If the appliance is still brand new and covered by warranty, your expenditures can be greatly reduced. However, if it has passed its guarantee, you can be responsible for paying the whole price, regardless of your decision.
How come my washer is so loud?
A worn-out drum bearing or a damaged drive pulley are the most typical causes of a washer creating a loud noise during the agitation cycle. When the drum spins, these flaws typically produce a grinding or rumbling sound.
When your windshield wipers quit functioning, what does that mean?
The easiest and first thing to check is this. The fuse may have been overloaded and blown due to accumulation of ice and snow on the wiper blades or some other stress on them.
You can use a website like this one or your owner’s manual to locate the fuse box in your car. The wiper fuse can be found by first finding the fuse diagram for your car. Purchase a replacement fuse with the appropriate amperage, then exchange the outdated one. If your wipers start working again, the issue was most likely a blown fuse.
- Parts cost about $10 for a selection of 100 fuses.
- Professional labor costs $20 to $50.