A 2008 Santa Fe 3.3L Limited has a new radiator and hoses that I installed. In order to tilt the A/C condenser and have more room to remove the radiator, you must first remove the front bumper cover.
Front bumper covers are simple to remove. It can be difficult to remove the plastic pieces holding the bumper cover in place because the Phillips screw head may shred or become stuck when you try to unscrew it. It only required a little flat-blade screwdriver to pry up on the screw and pull it out again.
1. an empty radiator
2. ad duct air removal
3. cut the hoses
4. Unplug the fans’ connectors and take out the drivers’ side fan before removing the passengers’.
5. Removed the two rubber hoses that connect to the radiator’s bottom (I think automatic trans lines)
6. To tilt the radiator forward so it may be removed, unscrew two bolts located near the top of the A/C condenser.
Note: The instructions are for a 3.3L, but you should have more space with the 2.7L. However, it ought to be the same.
In This Article...
Service to Replace Car Radiators
The typical price for replacing the radiator in a Hyundai Santa Fe is $488, which includes $288 for supplies and $199 for labor. Prices may change based on where you are.
What you’ll need
A Hyundai Santa Fe’s radiator replacement procedure. Your car’s radiator may rust and degrade with time, leading to leaks and overheating. Because you have to take out so many engine parts before you replace the radiator in a Hyundai Santa Fe, it can be a challenging project. If you are mechanically inclined, you might want to take up the project. The popular 2001 Hyundai Santa Fe’s radiator can be changed in the following manner.
Disconnect the negative battery cable after removing the air duct. Remove the air cleaner assembly and pour the cooling system’s liquids into a container that can be sealed. Remove the cooler lines from the transmission and the inlet hose from the radiator.
Remove the fan shroud bolts from the condenser bracket and the fan shroud clips from the condenser tubes. Air deflectors should be removed.
Remove the radiator support brackets on the fan shroud and disconnect the coolant hose from the radiator overflow. The engine cooling fan motor’s electrical connectors should be disconnected, and the fan motor harness should be freed from the fan shroud clips. Get rid of the fan shroud.
Disconnect the transaxle oil cooler pipes and remove the radiator’s outlet hose.
Remove the condenser brackets and tile the radiator towards the back. Condenser brackets and mounting tabs should be raised and moved out of the way. Install the new radiator after carefully lifting the old one out of the engine area.
The engine’s parts should be put back together and connected in the opposite order that they were taken out.
Mix equal parts water and engine coolant to fill the new radiator. Start the engine, let it run for a few minutes, then switch it off and, if necessary, add more fluids. Negative battery cable reattached.
How much does a radiator for a Hyundai Santa Fe from 2006 cost?
For your 2006 Hyundai Santa Fe, we now offer 6 Radiator options to select from, with prices ranging from $141.78 to $329.99.
How much does a Hyundai Santa Fe radiator cost?
Estimated cost to replace the radiator on a Hyundai Santa Fe. Hyundai Santa Fe radiator replacements typically cost between $1,027 and $1,177. While parts are priced between $809 and $901, labor costs are expected to be between $219 and $276.
How is a radiator changed?
- Security first. There are electrical connections on your radiator.
- Examine or replace.
- Radiator draining
- Radiator must be unplugged.
- Get rid of the old radiator.
- Reinstall the Radiator.
- Include Coolant.
- Bleed the cooling system’s air
What else has to be replaced when a radiator is replaced?
Coolant is continuously circulated through the cooling system’s tubes and passageways by the water pump, which employs an impeller. The impeller is actually constructed of plastic in the majority of engines.
As a result, the radiator will sustain abrasions and other types of damage from any impurities or hard material that separates from it. The high temperatures could potentially harm the plastic components if the radiator stops cooling the fluid before it passes the impeller. A centrifugal pump’s impeller, which rotates to move fluid, may eventually break apart in little pieces, slowing the coolant’s flow rate.
What equipment do I require to replace a radiator?
- that new radiator (goes without saying really)
- new mounts for radiators
- two adjustable wrenches
- a bowl for washing up
- A key for bleed radiators
- Pipe, Cable, and Stump Detector
- a drill, either a drill driver for interior walls or a hammer drill for masonry walls.
- a drill bit for brickwork
- a little steel wool
- rags or towels for spills
- A PTFE tape (also called thread seal tape)
- Someone who can assist you
Can I change a radiator on my own?
If you know what you’re doing, changing your radiators is a fairly simple task that can be completed in a matter of hours. Finding a radiator that is exactly the same size as your old one and replacing it like for like is the simplest method.
If you consider yourself capable of most DIY chores, you should be able to complete this one on your own, but it will require some work and some talent.
But take care—if something goes wrong, you can find that your carpets and wall paper have water damage!
How much does a radiator replacement cost?
Homes with radiators usually have a central boiler that connects via pipes to a network of radiators positioned thoughtfully about the home. The first step in a home radiator replacement is confirming that the radiator is, in fact, the issue because there are other elements involved. In actuality, the pipes or boiler are frequently the components of a heating system that need to be replaced because they are sometimes the most durable ones. In other words, troubleshooting before replacing could help you avoid wasting money.
The next step is to figure out how much it will cost to replace the radiator and determine whether any further adjustments are necessary. The fundamental cost breakdown is as follows:
- Cost of replacing a boiler: Frequently, the boiler needs to be replaced rather than a radiator. It is the most expensive component of the system and can be replaced for anywhere between $1,500 and $15,000. However, most homeowners spend about $8,362 on it. Although size and efficiency are the main drivers of price, the type of boiler you choose also affects how much you pay. Traditional gas and electric-powered boilers are typically less expensive, whereas geothermal heat pumps are more expensive initially but save you money on your energy bill over time.
- Cost of labor and installation: You should never try to replace a home radiator on your own. Hire a certified expert to complete any repairs or replacements, and make sure you compare prices before selecting someone. The price of installation will change depending on the type of system. Installing a piped (hot water and steam) radiator system will cost you between $600 and $800, while installing an electric radiator system would cost you between $200 and $450.
How much time does a mechanic need to replace a radiator?
My car’s radiator needs to be replaced because I recently moved, but I don’t know any of the mechanics around here and I’m scared about getting ripped off. How long does changing a car’s radiator typically take?
In less than two minutes, find out if your auto insurance is being overcharged.
Radiator replacement shouldn’t take more than two or three hours if it is done by an expert. It might only take an hour or so at most, but don’t be shocked if it takes a little longer.
By changing your radiator yourself, you may be able to save money on labor costs, but novice do-it-yourselfers beware: changing a radiator is not for the faint of heart. If you don’t know what’s going on under the hood of your automobile, changing the radiator might take you most of the day. Of course, anything is possible if you are up to the task!
Both [auto insurance shopping] and simple repairs like replacing a radiator shouldn’t consume all of your time. Because of this, Jerry makes it simple to
Starting the Jerry app only takes 45 seconds after downloading it. Customers of Jerry save more than $800 annually on their auto insurance!
How much coolant should I add after changing the radiator?
To dilute concentrated coolant, adhere to the manufacturer’s instructions. In a clean bucket, thoroughly combine the coolant and water. Use only distilled water—never tap water—to avoid mineral deposits on the surfaces of internal engine and radiator components. To lessen the chance of air pockets collecting in the engine, leave the car lifted while you refill the radiator.
Fill the radiator or coolant tank gradually with new coolant until it reaches the level indicated by the full mark on the coolant tank or 1 inch below the radiator’s neck. Let the engine run after starting it. The coolant level in the radiator/coolant tank will soon decrease as the engine warms up. It’s time to add extra coolant to raise the level to the top of the radiator or to the “HOT” mark on the coolant tank because the thermostat has opened as a result. If your car needs a unique air bleeding technique, see your owner’s manual or service manual. After checking for leaks, you should lower the car, install the cap, turn the engine off, and go for a spin.
Is it possible to swap out a radiator without draining the system?
However, there are advantages to changing the radiator valve without completely draining the system if you are only replacing one radiator. For instance, your central heating system’s water contains heating additives and inhibitors to help keep the system safe.
How simple is it to take a radiator out?
A radiator may be taken out quite easily. A skilled house plumber ought to be able to handle it with little difficulty. Since the pipes will already be accessible, it is one of the last items a building contractor installs. That’s assuming your back doesn’t mind the occasionally odd positions you have to adopt!
We’ll walk you through it if you need to remove a radiator in your home but are unsure of where to begin. But first, let’s talk about the potential requirement for radiator removal.
How is a radiator hose reattached?
- Before touching or opening the radiator in your car, make sure it has cooled down.
- Drain the radiator by setting a sizable pan underneath it and removing the drain plug.
- The hose clamps on the hose’s two ends can be taken off with a flat head screwdriver.
- the new radiator hose with hose clamps and position it correctly.
How long does installing a new radiator take?
When switching your current design for a new designer radiator option, it will typically take about 20 minutes to change radiators. Our comprehensive Advice Center blog, How to Replace a Radiator, lists all the tools you need and explains everything you need to know to quickly and efficiently change your radiators.
Is it possible to fix a radiator leak?
Taking your automobile into a repair facility for routine maintenance is the only long-term solution for a radiator leak. In order to check for fluid leaks, corrosion, and wear, a qualified technician at Thompson Sales will inspect the radiator itself, the reservoir, hose, clamps, and any nearby engine components.
Does fixing a radiator make sense?
If not properly maintained, the radiator hoses, core, and housing might develop tiny holes and broken portions. When there are issues with the cooling system, it is advised to fix them yourself or to hire a mechanic as soon as possible because they are crucial to the health of your car.