Car keys with low batteries can be annoying, but they are simple to fix! To replace the battery in your Hyundai key, follow these steps:
- By pressing the metal tab on the back of your key, you can take out the spare physical key. By turning the key in the hole it is placed into, you can pop the plastic fob casing open.
- The battery can be seen on the other side of the shell when the circuit board has been gently removed.
- Consult your owner’s handbook to determine the battery you require before removing the old one and installing the new one. Ensure that the negative side of the new battery is facing up when it is installed.
- Reinstall the circuit board, clamp the plastic casing close, and insert the metal key once more.
Your car key’s battery is now fully charged in an instant! You risk being locked out of your car if your key isn’t working, so having extra batteries on hand is a good idea.
Roadside assistance is something Jerry can help you with if you want to be protected the next time your battery dies. As a licensed broker, Jerryas offers you access to the best roadside support available, including features like towing, lockout service, and a mechanics hotline. To find out if you’re eligible for a reduced rate of $50 for your first year, check the app or give one of our helpful representatives a call!
In This Article...
Changing the Battery in Your Hyundai Key Fob
The battery in your Hyundai key fob is simple to change. A replacement CR 2032 3V battery is all that is required. They typically cost between $3 and $5 for a pack of 5. Wearing latex gloves is advised because you will be contacting a motherboard during this process, which could result in unintended harm.
- Remove the emergency key from the fob’s base.
- Between the release button and the key slot, insert the key.
- Turn the key until the fob pops open as if you were unlocking a door.
- Open the fob while facing the buttons downward (otherwise they will fall out).
- Remove the barrier and motherboard, then set aside the button-side of the fob.
- Remove the dead battery from its mount using the key.
- Place the + side of the new battery in its bracket.
- Replace the fob’s button-half, motherboard, and barrier.
- Set the release button peg in the appropriate hole.
- Reassemble the fob with a snap.
You’re done now! Press any button to put your Hyundai Smart Key to the test. If all was done correctly, a tiny red light should flash over the unlock button.
A Hyundai key fob uses what kind of battery?
A CR2032 battery powers the majority of Hyundai key fobs. Once you have a new Hyundai key fob replacement battery in your possession, insert it into your key fob exactly where the old one was. Check to see if the battery is in contact with each connection.
Where is the Hyundai Tucson’s smart key holder?
This information caught my attention. I think it would also benefit our Palisades!
Fix 1: While tapping the brake, push the Start button using the rear or end of the dead key fob. Fix 2: Place the dead key fob, buttons facing up, in the Smart Key slot (located in the locations specified below), and depress the brake while pressing the Start button.
Slots for Smart Keys: There are three places where these slots can be found: 1. on the front of the center console; 2. behind a panel right below the infotainment control knob; or 3. on the left side of the glovebox when it is open.
I can’t get my Hyundai key fob to open.
You must first depress the metal button or tab to release the actual key before you can open the key fob on a Hyundai. The fob will then pop open once you insert the key into the hole and move it around. Despite being somewhat high-tech, your key fob is robust.
How is a key programmed after a battery change?
Turn the key back to the “Off” position while holding down the lock button on the fob. At least three times, go through this process, finishing with the key in the “On” position.
This notifies the electronic control modules in your automobile that the signal is coming from your key in the ignition, and it then saves the information.
How is the Hyundai Smart Key pry opened?
To remove the metal key, push the metal button next to it. Open the Hyundai key fob by inserting this key into the little opening in the rear.
Why won’t my key fob function when I change the battery?
A dead battery is the most frequent cause of a key fob not functioning. Having said that, your keyfob might be having more serious issues. You might require a key fob replacement or perhaps auto door lock repair if your key fob stops operating after a battery change.
How is my car key fob reset?
- Take hold of all of your car’s remote starters.
- Place your ignition key in and select Accessory (or press the start button once without pushing the brake pedal).
- Your remote car starter’s Lock button should be pressed.
- After turning it on for five seconds, turn the key back to the “off” position (or press the start button again).
- The on-off cycle should be repeated a total of four times.
- You’ll hear a sound (a “ding,” “ping,” or “buzz”) on cycle number four when you choose the Accessory position. Right now, programming mode is active.
- Lock the remote by holding down the button (s).
- Turn off the car in ten seconds.
- Shut the door, exit the vehicle, and then try the remote.
- If so, that’s excellent!
- It’s time to call the dealership if it doesn’t.
If I change the battery, do I need to reprogram my key fob?
After changing the battery, you typically do not need to reconfigure the key fob. However, you might need to reprogramme it by re-pairing it with your vehicle if you’ve replaced not only the batteries but also some of the internal cabling and electronics.
Can I change a key fob on my own?
Yes, a replacement automobile key can be obtained without the original. Since people frequently misplace their car keys, replacing a misplaced car key is an easy operation. Nevertheless, depending on the key type, it could be pricey.
A key fob is a little electronic gadget that you can use to remotely lock and unlock your car. Other capabilities of the fob could include a remote engine starter, a trunk opening, or a proximity system that allows you to open your car without taking the fob out of your pocket.
Depending on how sophisticated the key technology is, replacing car keys can be expensive. An old metal key can be duplicated for less than $10 at a hardware store. On the other hand, the most recent smart keys must be ordered from a dealer and might cost between $200 and $500.
Your car key’s battery can be changed easily by opening it up, identifying the battery type, and going to the store. If you’re unsure of how to open the remote, it pays to consult your owner’s manual because you don’t want to force anything open and break it.
Today’s automobile keys are more secure and capable thanks to technology, but the gain isn’t free. The majority of modern keys feature complex electronic parts that must be configured before usage.
You may be able to buy an after-market key fob via a locksmith or online if your automobile is more than five years old. These sorts of fobs range in quality, but they are less expensive than other options.
You might be able to program a replacement yourself, depending on the make and type of your vehicle. The steps for programming a key fob yourself can differ: Owner’s manuals from certain automakers include instructions. In many circumstances, information can be available online. The catch is that in order to complete the process quickly or at all, you might need two functional key fobs.
It’s wise to acquire and program a backup remote before you require it. Additionally, a lot of used-car buyers (particularly auto dealers) will pay more for a vehicle with at least two functional key fobs or sets of keys.
A misplaced automobile key can indeed be replaced by a locksmith. If you have the option of receiving your replacement key from a locksmith or the dealership, the latter may be less expensive. Before making a choice, be sure to inquire about prices with your nearby vehicle dealership.
What occurs when the battery in your key fob runs low?
The transmitter’s range decreases as the fob battery gets weaker. This implies that for the key fob to operate, you must be close to the vehicle. When a smart key fob is in your pocket or handbag for automobiles with push-button starts, the car might not always detect it if the battery is low.
How often should the key fob’s battery be changed?
Car key fobs are so practical that it’s simple to ignore them. But did you realize that regular maintenance is required for your key fob? Batteries for key fobs should be changed every three to four years, though this will depend on how frequently they are used and how well they are made.
You’d wish you had taken better care of your key fob if it were to abruptly cease working while you were far from home. Avoid being stranded and having to pay for a tow because your key fob isn’t working properly. Here are some red flags that could indicate that it’s time to replace your key fob batteries before it’s too late.
Key fobs: Do they have batteries?
The past ten years have seen a significant development in key fobs. Push start systems of today are an evolution of what was once only a convenient technique to remotely lock and unlock doors. Despite the fact that key fob technology is continually evolving, their power source has not changed. Batteries power key fobs and other auto remote controls. That implies that the battery inside them needs to be changed when it runs out of juice. Batteries Plus can assist if your key fob isn’t working as well as it once did. For answers to all of your questions about automobile remotes, including what kind of batteries they need, how long they last, and where to buy a replacement battery, continue reading.
Are key fobs replaced by AutoZone?
AutoZone does offer key duplication services for cars made by Toyota, Ford, Honda, Dodge, GMC, Mercedes, Kia, and other manufacturers. These services include key duplication, transponder keys, key fobs, and vehicle key blanks.