The initial steps are the same whether your garage door operates with fixed code or rolling code. We advise having a step ladder on ready if you have a rolling code opener or are unsure of the type of garage door you have.
- The HomeLink buttons should be held between 1-3 inches of the garage door remote.
- Press and hold both the HomeLink button you want to configure and the open/close button on your garage door remote at the same time.
- When the HomeLink indicator light flashes, hold both buttons.
- A solid or quick flash will occur on the HomeLink indicator light.
Depending on what the HomeLink indicator light performs, move on to the correct area below.
In This Article...
Owners of Hyundai, Begin Here
Trying to set up your Hyundai’s HomeLink? The steps you must take to quickly and easily train your HomeLink are explained in the video on the right side of the page. The most frequently required video will start playing immediately, however we have added manufacturer-specific movies below the main player for some garage door openers.
Not a fan of video? By selecting your vehicle’s model name from the list below, you may also get comprehensive instructions tailored to your particular model.
Choose your training films from the list below the main video for Hyundai owners who are using a Genie, Sommer, or an older model of HomeLink (model years 2008 and earlier).
a manual for setting up the buttons on your Hyundai garage door
- Press and hold the two outside garage door buttons (on the left and right) until you see the red light next to them start to flash while the garage door is closed and the car is parked outside.
- Next, choose whatever Hyundai garage door button you want to configure. Then, while simultaneously pushing and holding the HomeLink garage door button on your Hyundai’s rearview mirror, press and hold the corresponding button on your garage door device. Continue doing this until you notice the red light solidifying or rapidly flashing. If the flash is slow, the system is still in the programming phase.
- As a last step, verify that the button has been programmed. You can move forward if it works. If not, you should still use the instructions below because your garage door might use a rolling code system.
How do I set up my Hyundai Sonata’s garage door opener?
Press and hold the HomeLink(r) garage door button on your Hyundai rearview mirror while simultaneously pressing and holding the garage door button on your garage door remote control inside your Hyundai car. Hold down the button while waiting for the red light in your rearview mirror to solidify or start flashing quickly.
How do I set up the garage door opener on my Hyundai Sonata 2022?
- Double-click the HomeLink button you want to program.
- Exit your Hyundai and press the Learn/Smart button once on your garage door opener.
- Return to your Hyundai in 30 seconds, then push the HomeLink button three times to program it.
Without a remote, how can I configure my Hyundai garage door opener?
Without a remote control, it is impossible to program a garage door opener. But the buttons on your car’s garage door opener can be reset using your remote transmitter. Alternatively, you can operate the door without a remote by using an electronic keypad.
- Press the program and arrow buttons at the same time on keypads. Before choosing your own, restore the brand’s default code.
- Press the two “end buttons” on control boxes to erase prior settings. Then sync your car’s buttons using the remote control.
How can I program a different remote to operate my garage door?
Next to the copy remote, place your original remote. You must first press and hold down the Original Remote button you want to program to the corresponding button on the Copy Remote before you can also press and hold down the Copy Remote button. Hold down both buttons until you notice the Copy Remote’s LED begin to flash quickly. After a few period of time, you should have successfully copied the code from the original remote.
If necessary, repeat the code cloning process for Copy Remote buttons B, C, and D.
The cloning process is now complete when the LED turns on and stays on when any button on the Copy Remote is pressed, and the Copy Remote’s buttons behave identically to those on the Original Remote.
How can I set up my garage door opener in the rearview mirror?
- On the rearview mirror, press the HomeLink button.
- Hold the rearview mirror 2 to 3 inches away from the garage door opener.
- The Open Button Must Be Pressed and Held Until a Green Flashing Light Appearance.
- When the light stops flashing, press the HomeLink button to test it.
Which button on a Chamberlain garage door opener is the Learn button?
Your garage door opener’s “Learn” button can be found above the antenna wire that hangs from the motorhead or it could be hidden by a light cover. There will be a green, red/orange, purple, or yellow “Learn” button.
Hyundai Sonata: Does it feature HomeLink?
Visit our most recent guide for Hyundai vehicles made in 2018 or after as these instructions might not apply to more recent Hyundai models.
The HomeLink feature on your brand-new Hyundai Sonata is one of the coolest extra features around. It transforms your car into a wireless control system that lets you operate your home’s security system, turn on or off electronics or appliances inside, as well as open and close your garage door and front gate. Follow the instructions listed below to connect your Hyundai Sonanta’s HomeLink to your garage door and stop looking for the annoying garage button forever!
How do I set up LiftMaster HomeLink to connect to myq?
You might need to take further steps to connect your garage door opener and your car’s HomeLink system if the following instructions didn’t work.
Find the learn button on your garage door opener first. This gadget is in charge of conveniently clearing the machine’s memory or configuring remote controls and garage door accessories. The learn button for a LiftMaster garage door opener is typically a red, orange, green, purple, or yellow button on the device’s back panel.
Try these steps to connect your HomeLink buttons to your garage door opener after you’ve found the learn button on your opener:
- Press and then let go of the learn button on your garage door opener.
- Press and hold the HomeLink button on your car for 30 seconds.
- The car will be connected to the machine’s signal by holding down the HomeLink button.
- The light on your LiftMaster machine will blink once if the pairing was successful.
- By pressing the button inside your car and watching for the door to open, you may test the system.
Hyundai HomeLink: What is it?
HomeLink(r) is, to put it simply, an in-car garage door opener that enables you to do away with your remote control. Our HomeLink(r) setup guide can assist you in getting this feature set up in your new or used Hyundai so you can start utilizing it right away.
How do I link my car to myq?
You use your garage door frequently, so it’s crucial to have quick and simple access to your house. Setting up your car to be recognized by the garage door opener at your house is an excellent approach to make sure of this.
- Hold down the two outside buttons at the same time until the in-car LED begins quickly flashing to erase any factory-programmed data from your in-car system. This could take up to a minute (in most circumstances, the car door needs to be closed and/or the key should be on the auxilary).
- Choose the button that will serve as the in-car garage door transmitter. Press the garage door remote control and the chosen in-car transmitter button at the same time while holding your transmitter up close to the chosen button. Keep pressing the buttons until the car’s LED light starts to flash quickly. This makes your car’s in-dash remote the primary transmitter for your garage door opener, but you are not finished yet. This in-car transmitter must now become your own transmitter.
- Go to your garage door opener’s Learn Button. The button is typically located close to where the motor head and floppy antenna are attached. With Genie, it is typically located beneath the light lens, and pressing it will cause an indicator light to flash red. With Sears or LiftMaster (Chamberlain), it is a red, green, or purple square button with a green, amber, or purple indicator light that is located close to or a part of the terminal screw board. Press this button to learn for a moment. When using Genie, the indicator light will turn on and blink; otherwise, it will remain lighted.
- Go back to the in-car transmitter button you previously programmed for Genie systems, and push it three or four times, or until the door begins to move. This should link your garage door opener and in-car transmitter.
- Press and hold the in-car button you preset for LiftMaster, Sears, or Linear Megacode until the garage opener light flashes.
Congratulations! Your car’s interior control system is now set up and prepared to open your door.
Please visit LiftMaster’s myQ support page if you require assistance at any stage of this procedure, or get in touch with a nearby garage door specialist.
The HomeLink transmit button is not visible.
Your HomeLink buttons are normally found in the overhead console, center stack, or mirror of your car, but their exact location depends on the make, model, and year of your vehicle. Please consult your owner’s manual if you are unsure of where your HomeLink is.
Can HomeLink be installed without a remote?
Try pressing the preprogrammed button to see if your garage door opens and closes. If it does, your effort has been fruitful. In the event that it doesn’t, repeat the process.
You may move a few little switches around to create any passcode you like. It should be comparable to the password on your phone. You won’t replace it unless you decide it’s no longer secure, at which point it will stay the same.
Note: If you have an earlier HomeLink garage door opener, there are no instructions for configuring it without a remote. In the HomeLink system, a code cannot be manually set. You need to utilize a remote to program it.
Most of the steps are the same. Make sure the door is shut, the key is not in the ignition, and any outdated programming is cleared away.
- Simply push both the remote button and the HomeLink button you wish to program while holding the remote up to the HomeLink button.
- Hold them until you notice the in-car remote’s LED starting to flash quickly.
My HomeLink button is red; why is that?
When you press it again, the light ought to be red. This indicates that your 3-button remote is now prepared for HomeLink(r) system programming.
Why won’t my HomeLink function?
Interference close to the house or car, the use of stale batteries in the original transmitter during programming, or other factors can affect range.
- Your handheld transmitter needs a fresh battery. More power is drawn from the battery when the HomeLink(r) is being trained than when you press the doorbell button. It can occasionally assist the portable transmitter pick up a better signal and extend its range by replacing the battery.
- Retrain the HomeLink by moving it to various positions and angles. Hold the portable transmitter 3 to 4 inches from the buttons at first, then 5 to 6 and even 6 to 8 inches. This can occasionally aid in obtaining a stronger HomeLink signal.
- Make use of fresh batteries in a second transmitter.
- Adjust the antenna wire that hangs from the motorhead of the garage door opener.
Which automobiles have HomeLink?
Numerous more technological components connect with advanced car technology. For added convenience, consumers who have smart home systems want to link their homes and vehicles. One system makes it simple for you to achieve that. Hundreds of automakers, including Audi, BMW, Chevrolet, Ford, Honda, Hyundai, Mercedes-Benz, and Toyota, include it as standard equipment in their vehicles. Additionally, it’s accessible as an aftermarket add-on.
It is known as HomeLink. Although the system has been in place for years, not everyone is aware of what it is or how to operate it. You may use it to access virtually any smart home feature simply pressing a button in your car.