The battery in your Hyundai key fob is simple to change. A replacement CR 2032 3V battery is all that is required. They typically cost between $3 and $5 for a pack of 5. Wearing latex gloves is advised because you will be contacting a motherboard during this process, which could result in unintended harm.
- Remove the emergency key from the fob’s base.
- Between the release button and the key slot, insert the key.
- Turn the key until the fob pops open as if you were unlocking a door.
- Open the fob while facing the buttons downward (otherwise they will fall out).
- Remove the barrier and motherboard, then set aside the button-side of the fob.
- Remove the dead battery from its mount using the key.
- Place the + side of the new battery in its bracket.
- Replace the fob’s button-half, motherboard, and barrier.
- Set the release button peg in the appropriate hole.
- Reassemble the fob with a snap.
You’re done now! Press any button to put your Hyundai Smart Key to the test. If all was done correctly, a tiny red light should flash over the unlock button.
In This Article...
The Hyundai Elantra key fob uses what type of battery?
A CR2032 battery powers the majority of Hyundai key fobs. Once you have a new Hyundai key fob replacement battery in your possession, insert it into your key fob exactly where the old one was. Check to see if the battery is in contact with each connection.
How is a key programmed after a battery change?
Turn the key back to the “Off” position while holding down the lock button on the fob. At least three times, go through this process, finishing with the key in the “On” position.
This notifies the electronic control modules in your automobile that the signal is coming from your key in the ignition, and it then saves the information.
How can I reset my key now that my battery is new?
The majority of people use their key fob to unlock their car doors and trunk. But what occurs if the battery runs out? You might believe that getting a new key fob requires visiting a dealership or a locksmith, but did you know that you can simply reset it yourself?
This is how:
Find the little button on your key fob first. This is typically found on the fob’s backside.
2. For around 15 seconds, press and hold the button.
3. Release the button after 15 seconds, and your key fob should be reset!
The owner’s manual for your car should always be consulted if you have any issues or inquiries.
Simply press and hold the reset button for a few seconds if your key fob has one. Remove the battery cover and press the tiny reset button on the circuit board if your key fob lacks a reset button.
I can’t get my Hyundai key fob to open.
By pressing and holding the metal tab or button, start by withdrawing the metal key. Next, insert the metal key into the little opening and turn it in either way to release the back cover of your key fob. The case ought to instantly open.
If I change the battery, do I need to reprogram my key fob?
After changing the battery, you typically do not need to reconfigure the key fob. However, you might need to reprogramme it by re-pairing it with your vehicle if you’ve replaced not only the batteries but also some of the internal cabling and electronics.
Why won’t my key fob function when I change the battery?
A dead battery is the most frequent cause of a key fob not functioning. Having said that, your keyfob might be having more serious issues. You might require a key fob replacement or perhaps auto door lock repair if your key fob stops operating after a battery change.
Key fobs: Do they have batteries?
The past ten years have seen a significant development in key fobs. Push start systems of today are an evolution of what was once only a convenient technique to remotely lock and unlock doors. Despite the fact that key fob technology is continually evolving, their power source has not changed. Batteries power key fobs and other auto remote controls. That implies that the battery inside them needs to be changed when it runs out of juice. Batteries Plus can assist if your key fob isn’t working as well as it once did. For answers to all of your questions about automobile remotes, including what kind of batteries they need, how long they last, and where to buy a replacement battery, continue reading.
Does anything need to be reset following a battery change?
A: In some vehicles, the battery charging system monitoring system needs to be reset after a battery replacement. A scan tool or specific battery reset equipment can be used to accomplish this.
Will a dead key fob prevent a car from starting?
Yes, a key fob with short battery life may prevent your automobile from starting. The key fob for your automobile is an electrical gadget with a battery inside that powers signals sent from the key fob to your car. Your car’s computerized systems get alerts in accordance with the key fob commands you press, and the vehicle subsequently reacts as necessary.
This function depends on the battery in your car’s key fob; if it runs out, you might not be able to start your car without a jumpstart. Your ability to start your car may be affected if the battery in your Honda keyless remote is low.
Can my car start without the key fob?
Push-button start and keyless ignition are two examples of the amazing and incredibly entertaining technology that comes with new cars. What occurs, however, if your keyfob is lost? The response is situation-specific. For instance, whether you lose your keyfob before getting into the car or after, your experience will be very different. Simply put, you won’t be able to start your automobile if you lose the keyfob that activates your push-button start before you try to drive in it. But what happens if you misplace your key fob while you’re on the road? That calls for a totally different response, and we have located a video that does just that.