A CR2032 battery powers the majority of Hyundai key fobs. Once you have a new Hyundai key fob replacement battery in your possession, insert it into your key fob exactly where the old one was. Check to see if the battery is in contact with each connection.
In This Article...
In a Hyundai key fob, what kind of battery is used?
The battery in your Hyundai key fob is simple to change. A replacement CR 2032 3V battery is all that is required. They typically cost between $3 and $5 for a pack of 5. Wearing latex gloves is advised because you will be contacting a motherboard during this process, which could result in unintended harm.
- Remove the emergency key from the fob’s base.
- Between the release button and the key slot, insert the key.
- Turn the key until the fob pops open as if you were unlocking a door.
- Open the fob while facing the buttons downward (otherwise they will fall out).
- Remove the barrier and motherboard, then set aside the button-side of the fob.
- Remove the dead battery from its mount using the key.
- Place the + side of the new battery in its bracket.
- Replace the fob’s button-half, motherboard, and barrier.
- Set the release button peg in the appropriate hole.
- Reassemble the fob with a snap.
You’re done now! Press any button to put your Hyundai Smart Key to the test. If all was done correctly, a tiny red light should flash over the unlock button.
What should I do after changing the battery in my key fob?
The majority of people use their key fob to unlock their car doors and trunk. But what occurs if the battery runs out? You might believe that getting a new key fob requires visiting a dealership or a locksmith, but did you know that you can simply reset it yourself?
This is how:
Find the little button on your key fob first. This is typically found on the fob’s backside.
2. For around 15 seconds, press and hold the button.
3. Release the button after 15 seconds, and your key fob should be reset!
The owner’s manual for your car should always be consulted if you have any issues or inquiries.
Simply press and hold the reset button for a few seconds if your key fob has one. Remove the battery cover and press the tiny reset button on the circuit board if your key fob lacks a reset button.
I can’t get my Hyundai key fob to open.
By pressing and holding the metal tab or button, start by withdrawing the metal key. Next, insert the metal key into the little opening and turn it in either way to release the back cover of your key fob. The case ought to instantly open.
Why won’t my key fob operate now that the battery has been changed?
A dead battery is the most frequent cause of a key fob not functioning. Having said that, your keyfob might be having more serious issues. You might require a key fob replacement or perhaps auto door lock repair if your key fob stops operating after a battery change.
How is a key programmed after a battery change?
Turn the key back to the “Off” position while holding down the lock button on the fob. At least three times, go through this process, finishing with the key in the “On” position.
This notifies the electronic control modules in your automobile that the signal is coming from your key in the ignition, and it then saves the information.
After changing the battery, does the key fob need to be reprogrammed?
After changing the battery, you typically do not need to reconfigure the key fob. However, you might need to reprogramme it by re-pairing it with your vehicle if you’ve replaced not only the batteries but also some of the internal cabling and electronics.
How much does a new Hyundai key fob cost?
It’s more likely that you will be allowed to utilize an aftermarket key fob if your automobile is at least ten years old, according to CR’s Ibbotson. Many of these less sophisticated fobs can be configured by the consumer, a local technician, or an automotive locksmith.
Ibbotson advises making sure to phone your neighborhood garage first to confirm that they can do the task, as key-fob programming equipment levels can vary from shop to shop. For instance, a Maryland-based repair shop called Murray’s Auto Clinics informed CR that they are unable to program key fobs for any vehicle with push-button start or keyless entry.
We took our vehicle to M.J. Sullivan Hyundai in New London, Connecticut, where we were charged $120 for programming (one hour of labor), which is what they would have charged us if we had purchased the key fob from them.
Hyundai sent us a laser-cut mechanical backup key for $72.47, bringing the total cost to $272.42 (the car waited at the shop for two days); if we had ordered the key fob through the store, the total would have been $428.92).
For some makes and models, you can purchase a cheap aftermarket fob and program it yourself if your home unexpectedly gains a third driver, such as a teenager.
We purchased a fob from BestKeys from Amazon for CR’s 2008 Chrysler Town & Country minivan. Although it lacks the Chrysler branding on the back, it resembles the two original fobs that came with the minivan when it was new. The uncut mechanical key and internal circuitry were both included in the $14.30 price. (However, we didn’t see the need to shell out the cash to have a locksmith cut that third key.)
Chrysler customers can program a third key fob themselves if they already have two functional ones, just like GM owners can. The owner’s manual contains clear and straightforward programming instructions.
Hyundai vehicles can be operated without a key fob.
Once the engine is going, the automobile will still work without the key fob. Additionally, switching from park to drive is trouble-free even when the key is not available.