The battery in your Hyundai key fob is simple to change. A replacement CR 2032 3V battery is all that is required. They typically cost between $3 and $5 for a pack of 5. Wearing latex gloves is advised because you will be contacting a motherboard during this process, which could result in unintended harm.
- Remove the emergency key from the fob’s base.
- Between the release button and the key slot, insert the key.
- Turn the key until the fob pops open as if you were unlocking a door.
- Open the fob while facing the buttons downward (otherwise they will fall out).
- Remove the barrier and motherboard, then set aside the button-side of the fob.
- Remove the dead battery from its mount using the key.
- Place the + side of the new battery in its bracket.
- Replace the fob’s button-half, motherboard, and barrier.
- Set the release button peg in the appropriate hole.
- Reassemble the fob with a snap.
You’re done now! Press any button to put your Hyundai Smart Key to the test. If all was done correctly, a tiny red light should flash over the unlock button.
In This Article...
Where is the Hyundai Elantra’s smart key holder located?
This information caught my attention. I think it would also benefit our Palisades!
Fix 1: While tapping the brake, push the Start button using the rear or end of the dead key fob. Fix 2: Place the dead key fob, buttons facing up, in the Smart Key slot (located in the locations specified below), and depress the brake while pressing the Start button.
Slots for Smart Keys: There are three places where these slots can be found: 1. on the front of the center console; 2. behind a panel right below the infotainment control knob; or 3. on the left side of the glovebox when it is open.
I can’t get my Hyundai key fob to open.
Start by removing the metal key from a Hyundai that is not too old by pressing and holding the metal tab or button. Then, insert the metal key into the minuscule opening and turn it in either way to release the back cover of your Hyundai key fob. The case ought should then open.
What about batteries for Smart vehicle keys?
A small battery powers the key fob. In a smart key fob, the battery may last for 2-3 years, whereas it may last for 4-6 years in a standard key fob. The key fob has a battery and a door key.
How do you unlock a 2020 Hyundai Elantra key fob?
By pressing and holding the metal tab or button, start by withdrawing the metal key. Next, insert the metal key into the little opening and turn it in either way to release the back cover of your key fob. The case ought to instantly open.
How can I make a key copy for my smart car?
There are two solutions to the query “How to get a replacement car key?” Visit your local auto dealer or make a locksmith appointment. If you’re unsure of whether approach would be simpler and more beneficial for you, you need think about a few facts. To begin with, there are specific circumstances in which you cannot visit your car dealer to obtain a new key. You won’t be able to get anyplace if your last key is lost or damaged. Additionally, if your car dealer stopped doing business in your nation or location, you cannot use this procedure. This approach isn’t a quick one because it could take a while.
Making a new key quickly and on the spot, just as securely as the old one, can be accomplished by calling a locksmith. Modern locksmiths are equipped with the necessary equipment and skills to offer you not only routine Smart key replacement but also more specialized services like Smart key fob reprogramming and Smart vehicle key battery replacement.
Why won’t my key fob operate now that the battery has been changed?
A dead battery is the most frequent cause of a key fob not functioning. Having said that, your keyfob might be having more serious issues. You might require a key fob replacement or perhaps auto door lock repair if your key fob stops operating after a battery change.
How much does a new Hyundai key fob cost?
It’s more likely that you will be allowed to utilize an aftermarket key fob if your automobile is at least ten years old, according to CR’s Ibbotson. Many of these less sophisticated fobs can be configured by the consumer, a local technician, or an automotive locksmith.
Ibbotson advises making sure to phone your neighborhood garage first to confirm that they can do the task, as key-fob programming equipment levels can vary from shop to shop. For instance, a Maryland-based repair shop called Murray’s Auto Clinics informed CR that they are unable to program key fobs for any vehicle with push-button start or keyless entry.
We took our vehicle to M.J. Sullivan Hyundai in New London, Connecticut, where we were charged $120 for programming (one hour of labor), which is what they would have charged us if we had purchased the key fob from them.
Hyundai sent us a laser-cut mechanical backup key for $72.47, bringing the total cost to $272.42 (the car waited at the shop for two days); if we had ordered the key fob through the store, the total would have been $428.92).
For some makes and models, you can purchase a cheap aftermarket fob and program it yourself if your home unexpectedly gains a third driver, such as a teenager.
We purchased a fob from BestKeys from Amazon for CR’s 2008 Chrysler Town & Country minivan. Although it lacks the Chrysler branding on the back, it resembles the two original fobs that came with the minivan when it was new. The uncut mechanical key and internal circuitry were both included in the $14.30 price. (However, we didn’t see the need to shell out the cash to have a locksmith cut that third key.)
Chrysler customers can program a third key fob themselves if they already have two functional ones, just like GM owners can. The owner’s manual contains clear and straightforward programming instructions.
If I change the battery, do I need to reprogram my key fob?
After changing the battery, you typically do not need to reconfigure the key fob. However, you might need to reprogramme it by re-pairing it with your vehicle if you’ve replaced not only the batteries but also some of the internal cabling and electronics.
What occurs when the battery in your key fob runs low?
The transmitter’s range decreases as the fob battery gets weaker. This implies that for the key fob to operate, you must be close to the vehicle. When a smart key fob is in your pocket or handbag for automobiles with push-button starts, the car might not always detect it if the battery is low.
Does anything need to be reset following a battery change?
A: In some vehicles, the battery charging system monitoring system needs to be reset after a battery replacement. A scan tool or specific battery reset equipment can be used to accomplish this.