When a dead battery prevents your ATV from starting, it is one of the worst experiences. I advise you to always connect your battery to a charger if it will be stationary for a period of time longer than a few weeks.
A power wire may be shorting someplace and depleting the battery, or the battery could die from leaving the key on. I connect my battery to a smart charger all winter long to maintain battery life so that my ATV can start easily in the spring.
to refuel the ATV’s battery. Connect your smart charger to the battery terminals after removing the side panel securing your battery from the elements. Leave the charger attached for roughly 4-5 hours for it to finish charging.
In This Article...
Can a car battery be used to jumpstart a four-wheeler?
An ATV can truly be jump-started using a car. This can be really helpful if you’ve just driven hundreds of miles to a spot only to discover that your ATV won’t start.
As you would with any other ATV/ATV or car/car setup, connect the wires. Don’t start the car after that. Since the car battery is far more powerful than the ATV battery, starting it could damage the ATV battery. Just attempt to start the ATV instead. It ought to turn over if the battery was the issue stopping it from starting.
These three techniques for starting your ATV batteries can be quite helpful if you get up stuck. It’s crucial for this that you understand your machine’s capabilities, power, and starting process. However, make an effort to always take good care of your battery and make sure it is in working order before you go.
Can a car battery be used to recharge an ATV battery?
ATV batteries cannot handle the 10 amps of current that standard car battery chargers provide. The battery may become irreversibly damaged if it overheats.
Use a car charger only if it has a preset to limit current to less than 3 amps.
Use the manual charger’s process if you can lower current to < 3 amps.
Can I Charge My ATV Battery With My Car?
Yes, you may use your automobile to kickstart your ATV and not charge the battery. If your ATV won’t start because the battery is dead, this is helpful.
Jumper cables should be used to connect the ATV and automobile batteries. Never start the vehicle. That could destroy the small ATV battery by delivering too much power.
A dead ATV battery can be revived using the car’s power. After a few minutes, unplug the jumper cables and attempt to start the ATV once more.
To be clear, this approach is just intended for jumpstarting. Since you have no control over the current and voltage it receives, do not use it to fully charge the ATV battery.
Do ATV batteries refuel while operating?
You might have observed that unlike cars, ATVs do not utilize alternators to charge their batteries. And you are aware that for the bike to operate effectively, the battery must always be kept full.
Electricity is needed for quite a few tasks, including the starter, cooling fans, lights, winch, power steering, heated grips, GPS, and other accessories.
An ATV’s battery is charged using either a stator system or a magneto system. This technology, which is housed inside the ATV’s engine, is reasonably straightforward and reliable. The stator continuously generates an electric charge while the engine is running. The many electrical components of the motorcycles are powered in part by electricity. The battery is being charged with what’s left of it.
How is a completely dead ATV battery recharged?
In a room with good ventilation, place the two batteries close to one another. Using jumper wires, connect the two batteries in the following configuration:
- Utilizing the negative (red) jumper cable lead, connect the two positive battery terminals (designated with the symbol “+”).
- Utilizing the negative (black) jumper cable lead, connect the two negative battery terminals (designated with the letter “-“).
Attention: The red lead’s other end is hot when it is attached to the battery. Avoid touching anything grounded, including the negative (black) jumper wire leads and battery connections, since doing so could result in a short. It can be extremely risky to short out a battery because doing so will probably result in irreversible battery damage.
How is a battery for an ATV jumpstarted?
If your ATV battery dies while you are out riding, you should ideally be with a friend or family member who also has an ATV because jumping an ATV with another ATV is probably the simplest solution. Bring the ATVs together first so that jumper cables may reach the batteries in each vehicle. Next, connect the jump cables—usually red and black cables—to the healthy battery. Afterward, connect the other end of the cords to the bare battery. Start the first ATV, or the one with the full battery, and let it run for a few minutes, perhaps three to five. Afterward, try to reactivate the dead ATV while the cables are still attached. Usually, this will work and your ATV will start right away. Now that the previously dead battery has been completely disconnected, you can remove the jumper cables from both it and the ATV’s fully charged battery. Before shutting it off, make sure to let it run for another 30 minutes or so to give the alternator time to fully recharge the battery. During this moment, you can either ride it or leave it idle.
How long does the battery in an ATV last?
An ATV battery will typically last for three to four years when used normally. An ATV battery may endure for more than five years with the right maintenance and care. If your battery is only surviving two years, there may be an electrical issue or improper battery maintenance.
Can a quad be bump started?
This technique is often referred to as popping the clutch or bump starting an ATV. Basically, you need to push the quad quickly enough for the engine to flip over and start when you let the clutch out. The majority of ATVs are light enough for an adult of average stature to drive them on level terrain. It is much simpler to achieve this if you can start moving downward.
Typically, the engine is started by your starter motor. When the engine is turned over, the battery is used to provide power, which ignites the spark plugs and starts the engine. Utilizing the tires and forward motion, the compression method turns the engine over.
A step-by-step guide is provided below:
- Place the quad in second gear.
- Activate the key and any run switches you may have.
- Keep the clutch engaged and accelerate the quad as much as you can (around 10 mph)
- Step on and release the clutch swiftly.
I’m done now! When you do this, the engine should start to turn over. Try giving it some gas when it begins to turn over if you’re having trouble. Once the engine has started, pull the clutch back in. That will stop the machine from running away from you right away. To get it done this way, it could take a few tries, but it does work.
Try shifting into third gear and continuing the process if the tires start to skid instead of turning the engine over. Try on more stable ground or someplace where the tires have more traction if the tires are still skidding. Once the engine is running, your battery should begin to recharge.
If your ATV is automatic, it won’t have a clutch and you might not be able to change gears. You won’t have the same results with the bump start (compression start) method. I’ve seen folks start their ATVs by putting them in neutral, rolling them along, and then putting them in drive. I do believe, though, that doing it this way could harm the transmission. As a last option, I would only carry out the action with an automatic.
What symptoms indicate a faulty ATV battery?
A multimeter is required. One with a max/min function is preferred. The display refresh rate of a multimeter without a max min setting may not be fast enough to reflect the true minimum voltage value, leading to a misleading reading.
- Start the test with a battery that has been fully charged and rested; refer to steps 1 and 2 above. The voltage value for the open circuit should be 12.4V or higher.
- DC voltage is selected on the multimeter.
- affix the leads:
- The red lead connects to the battery’s positive terminal.
- Black lead falls to the ground.
- To begin recording the voltage, press the min/max button. Alternatively, have someone else check the voltage reading.
- Start the engine. The battery is quickly depleted by the starter’s high current drain. If the ATV starts, that’s fine.
- After stopping the car, check your readings.
- ATV batteries shouldn’t fall below the 9.6V to 10.5V range in good condition (depending on battery CCA-rating and battery temperature at the time of testing).
- Your battery is probably damaged if the minimum reading is less than 9.6 volts. It can no longer accommodate enough.
How is a dead battery revived?
Distilled water, a voltmeter, a battery charger, and a syringe are required.
- Remove the rubber covering the caps and the battery.
- The distilled water can be used to recharge batteries.
- A battery’s acid can also be changed by combining fresh acid and distilled water.
How frequently should an ATV battery be charged?
Any kind of lead acid battery should always be kept charged all the way up. After doing that, you should either charge your battery around every 30 days or think about purchasing a smart battery charger to keep your battery maintained constantly. These modern “smart” chargers will maintain the voltage at its maximum level while almost completely eliminating the current, preventing overcharging even when left on for extended periods of time. Even while not in use or linked to anything, a motorcycle, boat, or ATV battery will eventually self-discharge; for this reason, a constant maintenance charger is advantageous.
Look through our variety of powersport batteries if you have charged the battery but it still won’t store enough power to start your motorcycle, ATV, or boat.
When I try to start my ATV, why does it click?
When you try to start your ATV, it probably clicks because of the battery. There are several causes for this, ranging from faulty connections to battery-draining current draws. If the battery is not the issue, the ATV’s starter solenoid is most likely broken.