The likelihood is that the gear that arrived with your automobile was used to attach your license plates, whether you drive a new $90,000 Porsche or a used $10,000 Toyota. That typically means inexpensive zinc-plated steel screws with poor corrosion resistance and much worse aesthetics.
The majority of the knowledge presented here is based on our experience with BMW cars, however the same general ideas hold true for any license plate hardware used in any automotive application.
In This Article...
What size screw goes into my license plate?
The normal screw sizes for license plates vary depending on the brand. These screws are known as Original Equipment Manufacturers (OEM) screws since they are produced by original equipment manufacturers. These particular screws are created specifically for particular car models.
A typical size of license plate screw is 1/4-14-3/4 inch, where 1/4 denotes the screw’s threaded diameter in inches, 14 indicates the number of threads, and 3/4 represents the screw’s length in inches.
The various types of license plate screws, their typical diameters, and the car models are displayed in the table below.
A license plate bolt or license plate screw with a common size, such as SNUG Fasteners, can fit almost all cars and trucks. A flathead screwdriver’s slotted head makes quick work of mending them.
They measure 1/4 x 3/8 inches and are made of quality stainless steel. Numerous domestic automobiles and trucks’ license plate slots can accommodate them.
Standard screw sizes are available for Revolution Rustproof License Plate Screws as well. They may be secured to practically all vehicles and trucks with plastic or nylon screw retainers and are self-tapping. They are made of premium stainless steel and measure 3/4 inches long.
Which types of screws does BMW employ?
To offer a minimal level of rust protection, this low-strength general purpose metal is frequently zinc-plated (see below).
highly brittle and typically covered in oil or black oxide. provides only modest corrosion protection.
a generally useful low carbon steel. The zinc coating offers a moderate level of corrosion protection, making it ideal for use inside or in other dry environments. Depending on the precise procedure, the color is either a yellowish tint or a blueish tint.
appearance that is smooth and fluid. The plating offers mediocre protection to corrosion.
It is suited for outdoor applications since it has excellent corrosion resistance. more expensive than steel with zinc plating.
greater resistance to corrosion than 304 stainless steel. resists solvents and pitting brought on by sulfur, chloride, and extreme outdoor conditions. commonly known as stainless steel “marine grade.”
alloys of copper having strong corrosion resistance. It is frequently softer than steel and stainless steel despite being a strong conductor of electricity. These materials, which are more expensive than steel, are frequently employed in decorative applications.
offers some corrosion resistance. It weighs one-third as much as steel and is non-magnetic.
more chemically resistant than stainless steel and resists corrosion caused by saline water. Despite being 40% lighter than steel, titanium is incredibly robust.
Make no effort. Although plastic screws don’t rust and have a certain aesthetic appeal, even a little tightening causes the heads to snap off. Only somewhat more durable than nylon. Use glass-filled nylon screws if you insist on using non-metal fasteners; they are the least harmful of all plastics.
What size screws go on a GMC license plate?
50 G.M. License plate screws are available from Disco Automotive under component number 1620PK. They have a 3/8″ head size and are 1/4″ (#14) x 3/4″ hex screws.
PRODUCT INFORMATION:
- 50 screws in each bag.
- Hasp Head
- Nickel Plated
- Screw for a standard G.M. license plate
DIMENSIONS:
- 1/4″ (#14) x 3/4″ Screw
- Size of Hex: 3/8″
- The item weighs about 0.3 pounds.
Profile of the Manufacturer: Disco Automotive Hardware As a master distributor of automotive fasteners for the automotive aftermarket, Disco Automotive first appeared in 1986. Since that time, they have remained a family-run business, and their first priority is ensuring that every customer is completely satisfied with the goods and services they receive. You can select from the well-liked plastic, nylon, and metal items among the thousands of different varieties of clips and fasteners. providing the finest selection and rates for you.
What sizes of bolts does BMW employ?
The usual bolt head size for BMWs is 17mm, so you won’t need to purchase additional sockets. Although the seat has a standard diameter, not all wheel brands may be compatible. Try our compact 19mm wheel nuts if the bolt bore on your wheels is small.
How are license plate screws fastened?
There are a few common screw sizes that are employed by the auto industry. The first is the 1/4″ – 14″ – 3/4″ self-tapping screw, which has a head that may accommodate a small-size socket or a flathead screwdriver. The majority of domestic automakers also utilize them for the rear, while they are commonly employed for the front plate.
The other are the M5 and M6 metric screws, which have threads that are 5mm or 6mm, respectively. The usual thread length ranges from 10mm to 16mm, depending on the manufacturer and application. Whether or not you use a license plate holder will determine how much thread you require. The screw must typically be 16mm long if it needs to pass through both the plate and the holder.
Are the screws on all license plates the same?
You should be aware of the ideal license plate screws for your vehicle out of the numerous varieties available. When considering the various shapes, sizes, types, and uses for license plate screws, the subject may appear confusing. The following frequently asked questions could get your mind racing:
Although the subject of license plate screws may seem complex, this article will guide you through the solutions to each of the questions raised above and act as your comprehensive guide to license plate screws.
How far apart are the bolts on license plates?
Given the specifications of the sheeting and the manufacturing process, the resulting 1/4 margin is required to guarantee satisfactory completed license plates. Bolt holes have a diameter of.3125 inches and are spaced from the plate’s center by +/- 3.5 inches horizontally and +/- 2.375 inches vertically.
An M8 screw is what size?
Metric bolts really have a predetermined diameter that is a little bit greater than the actual diameter of the bolt shaft. Therefore, an M8 bolt should pass through an 8mm hole because its shaft diameter is just under 8mm. But it’s customary to drill slightly wider clearance holes to account for misalignment.
When cutting a thread is required, the hole size must be lower to allow for tapping of the thread. By subtracting the thread pitch from the metric bolt diameter, it is simple to compute the required tapping hole size. For instance, a 6.75mm diameter hole would need to be tapped in order to accommodate an M8 bolt with a 1.25mm standard coarse thread pitch. However, the diameter of the hole needed for tapping would be 7mm if the M8 bolt had a fine pitch thread of 1mm.
Examples of clearance hole sizes, standard or coarse thread pitches, fine thread pitches, and their related tapping hole sizes are shown in the accompanying table.
Which plugs does BMW use?
External Torx Socket Set with 3/8″ Drive. E-torx hardware is used throughout BMW engines, making it a must for anyone performing engine work on a BMW.
How can I gauge the size of screws?
You measure the distance between the outer threads on one side and the outer threads on the other side to determine the diameter of screws and bolts. This is known as the main diameter and is typically the bolt’s correct size. To determine the minor diameter, you can alternatively take a measurement from one side to the other of the threads’ bottom cavity.
When describing sizes that are 1/4″ or less, a number is frequently utilized. An example of a nominal measurement is this. Here is the decimal equivalent of those integers.
The M6 screw is what?
Equipment is attached to a 19″ rack’s rack angles using rack screws. There are numerous sizes available, but the most popular ones are 10-32, 12-24, and M6. Manufacturers may use different exact threads.
The size designation “10” has no numerical significance. 32 threads per inch are indicated by the number “32”. The diameter of a 10-32 screw should be precisely 3/16″ to identify it (4.76 mm).
In pre-threaded racks, 12-24 rack screws are more frequent than 10-32. They resemble 10-32 hardware in terms of size and texture. The size designation “12” has no numerical significance. 24 threads per inch are indicated by the number “24”. The diameter of a 12-24 screw should be little smaller than 7/32″. (5.55 mm).
A 6 mm metric screw is referred to as M6. The threads have an outer diameter of 6 mm. An M6 x 0.1 mm rack screw is the typical metric size. There are 0.1 threads per millimeter, or 0.1 mm. An M6 screw can be identified by its diameter being slightly larger than 7/32″ (0.228″).