(You can even save $5 if your car was built after 2000 and has an OBD2 16-pin connector.)
Step 1: Connect this BMW INPA K+DCAN USB Interface to the DLC Diagnostic Link Connector connector on your laptop.
(Since the DLC port on my E46 is a round 20-pin connector while the INPA cable only has a 16-pin connector because it was made before 2000, I need a 20-pin to 16-pin connector.)
The BMW E46’s DLC port is located where:
Step 2: Run INPA program on WIN XP after installing it. Switch on the ignition and press “F2”. and select “Airbag” under the “Body” section.
Note: If you reset the airbag light but it comes back on right away or after some time, your car must have another problem.
In This Article...
Nidgeweasel
The dealer’s price for the mat is around EUR80. I have a reset tool, but there is no use in using it until the mat has been replaced. Bypassing the capacity of the owner to switch off the airbag in the software, the dealer can turn off the light, but the airbag will always be on. I am aware of this issue because my light has been on continuously. If you remove the bulb, it will still be on, but it is not as unpleasant. Hope this is useful.
How do I activate my airbag light?
The airbag light connects the seat belt system and the airbag system as part of the Supplement Restraint System (SRS) in automobiles (and vice-versa). When you turn on your automobile, the airbag light comes on for around seven seconds before going out, signifying that the internal system check was successful and finished. When the airbag light either never turns on or stays on while blinking, an issue exists. The airbag light needs to be reset at this stage.
Examining seat belt components, fixing bad clock springs, and replacing faulty sensors are a few techniques for turning off an airbag light. New bulbs or a fully charged battery are other options. While most repairs can be done without a professional, others may.
The following 10 steps will reset your airbag light:
- Turn on and off your ignition.
- Test drive your car when it has been restarted.
- Check the airbag switch for the passenger.
- Check to see if the seat belts are in place and functioning properly.
- Check to see if the passenger seat sensor is off.
- Use a scanner with the ability to reset the SRS or airbag light.
- Fix the broken airbag sensors.
- Replace or repair a broken clock spring.
- Check to see if the airbag is working properly.
- seek for a specialist’s help.
Although not exhaustive, the list above includes tried-and-true methods for tackling the problem. Some of them might not apply to your vehicle because compatibility is always based on the year, make, and model. It is recommended that you have your service manual on hand when carrying out any of these fixes. Always follow the manufacturer’s recommendations, too. Let’s get started on resetting your airbag light right away.
In a BMW, is the passenger airbag deactivatable?
I am aware that the weight of the passenger determines whether the airbag will deploy. Is there a setting or switch that can be used to turn off the airbag regardless of how much weight is in the seat?
Since the airbags are now connected to weight sensors in the seat, there is no switch to disable them. The knee, door, and front airbags are turned on and off automatically. I’m not sure if you could even disable the airbag using coding, however you might be able to. The data from the owner’s manual is listed below.
Wow. So someone made the decision that it is implicitly illegal to have a baby in a car seat in the front passenger seat?
It has been repeatedly demonstrated that infants shouldn’t ride in the front of a car due to the dangers of front airbag deployment, which can seriously hurt them, especially if they are in a rear-facing car seat. There is always a chance that parents will forget to deactivate the front airbags, which is probably why it isn’t an option in US cars (apart from the fact that it’s also against the law to place baby car seats in the front).
But it’s so inconsistently inconsistent. You cannot do this, but a lot of other things are free. IMO, this only serves to increase people’s stupidity.
Of all, by telling parents to keep their children in the rear and to avoid being distracted while driving, we are “protected” a lot here as well. But some really compact vehicles provide no alternatives. Must move to the front.
Why is my BMW’s airbag light on?
What it appears to be: A passenger seated in a chair with a seatbelt fastened holding a circle in their lap. The “SRS” symbol is illuminated in the dash of some cars.
What it means is When a problem is identified by your BMW’s computers within the airbag control unit, the airbag system, or supplemental restraint system (SRS) light will illuminate. If the SRS warning light is on, the system has been turned off, and the airbags won’t inflate in the case of a collision.
What to do if it comes on: When a car starts up, this light will briefly illuminate in the dash before going off, signaling that everything is working as it should and making it safe to drive.
Check to see if anything is obstructing the seatbelt click switch or if anything is piled up behind the seat, which could harm the wires, if the SRS light remains illuminated after starting the car or while it is in motion. If nothing is discovered, visit a local independent BMW repair facility as soon as possible to have a professional inspect and identify the issue. This is not something to be taken lightly, and it is safer to get this issue looked at by a certified BMW mechanic than to jeopardize your safety and the safety of your passengers by driving while it is still active.
How to turn the light off: After you bring your BMW to your neighborhood BMW shop, your mechanic will examine the component and the wiring, run code checks, and perform any necessary repairs.
An illuminated SRS light may indicate a sensor issue, the need to reset your airbags (for instance, if you were recently in a collision and the sensors were activated but the airbags did not deploy), or an issue with the seatbelts. Checking car bulletins is a good idea because there may be other instances when your airbags need to be recalled.
How does a BMW airbag reset work?
Could you please explain how to turn off the airbag light on my BMW X5? Every time I turn on my car, it has been coming on, and I have no idea how to turn it off. I’m hopeful that resetting the light will solve the problem.
In less than two minutes, find out if your auto insurance is being overcharged.
Unquestionably, resetting your airbag light is a solid first move. Observe these steps to reset the airbag light on your BMW X5:
- Upon starting your automobile, check to see if the airbag light is on.
- Then, after seven seconds, restart your vehicle.
- Two more times, repeat this procedure. Your airbag light ought to disappear.
It is advisable to have someone check over your car for you if the airbag light starts to illuminate once more. Given that sensors are frequently the subject of auto recalls, there may be an issue with the sensor or the airbag itself. The airbag will protect you and any passengers in the event of an accident.
The Jerry app makes sure you are prepared for the aftermath while airbag maintenance makes sure you are prepared for an accident.
The Jerry app, a registered broker that provides end-to-end support, compiles reasonable rates, assists you in switching plans, and even assists you in terminating your old policy.
My passenger airbag off light is on; why is that?
The Passenger Air Bag Off Light in the dash will illuminate if the passenger sensing system determines that no one is occupying the passenger front seat or if a number of other circumstances apply. You should understand what this means:
- Front passenger airbag is not deployed.
- You can also not have the passenger air bag deployed.
- In the event of a collision, the air bag will not deploy.
If there is an adult-sized passenger in the front seat and the Passenger Air Bag Off Light is on, this usually indicates that they are not seated properly.
Have the automobile inspected if the passenger adjusts their position and the light does not go out.
It might be necessary to shut off and restart the engine to get the light to turn off.
The informative nature of the aforementioned claims warrants independent verification. kindly visit our
Why does the airbag light turn on?
The airbag light will be on if your airbag has been deployed and has not been correctly reset. The light will turn on if the airbag hasn’t been deployed when the system detects that it can’t activate the airbag; this indicates that your car’s airbag system is having some sort of issue.
When this warning light is illuminated, does that suggest the vehicle’s airbags are deactivated and won’t deploy in the event of an accident?
Your automobile will alert you by turning on or flashing the dashboard or computer display airbag warning light. This light indicates that your airbags are deactivated while it is on. It implies that if you have an accident, they won’t deploy correctly.
Does the airbag become turned off if the battery is disconnected?
- By putting the work clamp close to the weld, the current route is kept short.
- removing and isolating the cords from both batteries. First, disconnect the negative battery cable.
- separating the device from the car’s systems as much as you can.
- keeping cords away from sensors or computers.
- removing computers or other delicate electrical components before welding if the distance is closer than 300 mm ” (12″).
- applying a welding blanket to the vehicle’s windshield and other exposed surfaces.”
“Before or during the inspection of the airbags and other SRS components, it is crucial to take specific safety precautions. To avoid unintentional deployment, the restraint mechanism is disabled as part of these safety measures. Even if an airbag appears to have fully deployed, it may still be able to do so again. Commonly, the negative battery cable is disconnected and isolated in order to disable the restraint devices. In order for the system to totally discharge, time must also pass. For instructions on how to disable the restraint system properly, consult the vehicle-specific service literature. It can also be necessary to disable the SRS to safeguard certain sections when welding or performing other types of repairs.”
Is the airbag fuse removable?
The airbag cannot be turned off by removing a fuse; even if it had one, which it does not, doing so would not turn it off. Cutting or twisting the wires or changing the impedence won’t make it work either; after all, the equipment is fail-safe.
Can an airbag light be caused by a low battery?
The backup battery is dead. It is the most frequent cause of an airbag light that won’t go off. It might take place if your car’s battery is running low or has been depleted for any other cause. When the battery is fully recharged, the issue will be resolved.
Driving with the airbag light on is it forbidden?
In some vehicles, it is even possible to turn off the passenger airbags, which will make your dashboard’s airbag light come on.
You should only deactivate the passenger airbag when absolutely necessary because, as was previously said, airbags are an essential safety element.
If your airbag light ever illuminates for no apparent reason, you should try to resolve the situation.
Clear the airbag light with a CAN OBD scanner?
Two categories of codes exist:
- Unhard Codes
- Precise Codes
Yes, most scanners allow you to delete soft codes after a problem has been fixed. These codes represent a malfunction with an element or component of the SRS system, such as
- vehicle airbag codes
- codes for seatbelts
- coded impact sensors
No, scanners are unable to remove these codes. These codes, which are also known as crash data, are kept following a car accident. These codes are also hardware error codes.