the ignition with the key (or key fob). While turning the key to position 2, avoid turning on the ignition. Open the driver’s door and hold it open for around ten seconds. The brake pad lights ought to reset once you’ve finished the aforementioned three steps!
In This Article...
Procedure
- Start the ignition, but do not drive. Press the START button if your BMW has one without depressing the brake pedal.
- Ensure that the time is displayed in the instrument cluster’s center.
- The ODO reset button should be pressed and held for roughly five seconds. The dash will first display a yellow triangle. Hold the ODO reset button down until the subsequent symbol appears.
- When the symbol for the front or rear brakes appears, repeatedly press the ODO reset button. Depending on the sensor you want to reset after replacing.
- When the preferred brakes’ symbol appears on the screen, press and hold the ODO reset button until the word “RESET” appears beneath the symbol.
- Release the button immediately when the word “reset” appears beneath the brake symbol, then press the button once again. Holding the ODO reset button down will make the brake light go out.
- The kilometers should become —–, signifying that the reset was successful. Although these intervals may vary between models, the next time you should have your BMW brakes changed is at 25000 miles for the front brakes and 31000 miles for the rear brakes.
On a BMW X3, how do you reset the brake light?
My car’s brakes were recently changed by my uncle, but the warning light is still on. Does a BMW X3 have a mechanism to reset the brake light?
In less than two minutes, find out if your auto insurance is being overcharged.
Every time the brakes and brake wear sensors are replaced on a BMW X3, the brake light warning must be reset. Fortunately, the brake light reset is simple and should only take a few minutes.
Resetting the brake light on a BMW X3 is made simple by:
- Do not start the engine after turning the ignition to the on position.
- Wait 30 seconds before opening the driver’s side door.
- Wait another 30 seconds after switching the ignition to the off position.
- start the vehicle
If the aforementioned fails, you should:
- Don’t start the engine after turning the ignition on.
- Up until the service menu appears, keep holding down the trip reset or odometer button. The service menu should show after holding the button pressed on the left side of the speedometer for approximately ten seconds.
- To find the brake warnings, use the reset button or, depending on the model, the controls on the turn signal lever to navigate through the settings.
- When prompted to reset the warning, press and hold the reset or BC button on the end of the turn signal lever.
- When prompted, press the reset or BC button once the screen indicates that it is resetting.
Finding auto insurance shouldn’t be a headache, but dealing with unnecessary warning lights can be.
Jerry is a helpful software that compares quotes from more than 50 leading insurance companies in a couple of seconds. When you locate an insurance you prefer, Jerry can assist with the transition and paperwork. It’s that simple!
How to reset the brake light on a BMW using method 1
- Start the ignition, but don’t let the vehicle go. Press the START button if your BMW has one without depressing the brake pedal.
- Verify sure the time is shown in the instrument cluster’s center.
- The ODO reset button should be pressed and held for 5 seconds. On the dashboard, a yellow triangle will first show. Hold the ODO reset button down until the subsequent symbol appears.
- When the front or rear brake sign appears, repeatedly press the ODO reset button. Depending on the sensor you wish to replace and reset.
- Press and hold the ODO reset button until the word RESET appears below the desired brakes symbol when it appears on the screen.
- Press the button once more once the word “reset” appears beneath the brake symbol. Holding the ODO reset button down will cause the brake symbol to vanish.
- The mileage ought to become zero, indicating that the reset was completed. You will have 25,000 miles for the front brakes and 31,000 miles for the rear brakes before your BMW brakes need to be changed again. Although these intervals could differ from one model to another.
Why is my BMW’s brake light on?
Another brake-related issue is worn brake pads. Your pads are represented by the BMW warning light symbol. If you notice a circle surrounded by broken parentheses, it’s time to schedule servicing and get them replaced.
Why does my BMW 328i have a brake light?
The brake warning light is a major matter. When you see it turn on, ensure sure your emergency brake is not engaged, then halt your vehicle as soon as you can. Your brakes could not operate at all if you have insufficient brake fluid.
On a 2017 BMW x1, how do you reset the brake light?
I was told to return in a month or less to have my brakes replaced the last time I went to the mechanic. I begged them to change them before it was necessary so I wouldn’t have to return so soon. Although the brake light turned on this morning, the brakes are in perfect shape. The mechanic advised me to simply reset the light, but how can I do that on my BMW X1’s brake light?
You made a wise decision by saving a trip and replacing your BMW X1’s brakes earlier than necessary! Fortunately, it only takes a few button presses to reset the brake light, and it won’t take you more than a few minutes.
You must: in order to reset the brake on your BMW X1
- Up until the service menu appears, keep holding down the trip reset or odometer button. The service menu should show after holding the button down for five to ten seconds. The button is normally located on the left side of the instrument cluster.
- When a popup appears asking you if you’d like to reset the warning, press and hold the reset button or BC button on the end of the turn signal lever.
Although replacing the brakes on your BMW probably wasn’t inexpensive, you can partially make up for your loss by using Jerry to get auto insurance discounts.
How can I turn off the braking alert light?
- To check that the brake pads and discs are in contact, repeatedly press the brake pedal.
- Turn off the dashboard for a brief period of time.
- Check to check if the light is still on after turning on the dashboard once again. Seek assistance and guidance if the brake warning light is still on.
Why won’t the brake lights on my car turn off?
A broken brake light switch is a common reason why a car’s brake lights won’t turn on. This part is attached close to the brake pedal under your dash. Your light switch may be stuck closed or the component may have failed if your lights are out.
Other signs of a broken brake light switch include malfunctioning brake lights, impaired cruise control, a car that won’t shift out of park, and brake lights that come on while you’re driving.
When the brake light is on, can you drive?
When you start your car, if the brake warning light illuminates and stays on, do not drive. Turn off your vehicle, then look for potential reasons of the problem (we will get to those soon).
Do not become alarmed if the brake warning light illuminates while you are driving or in traffic. There are multiple hydraulic braking systems in your car. So, even though it could take a little longer than usual to stop completely, pull over securely and arrange to have your car towed to your house or to a reputable technician for an inspection.
Once more, it’s crucial to avoid continuing to drive while the brake light is on as this could further harm your braking system and be quite dangerous.
*Pro Tip: All of the dashboard lights should come on when you switch on your car. If one or more of them are not turning on, there might be an issue with that particular indicator.
Where is the switch for the brake lights?
A little gadget connected to the brake pedal mechanism is called a brake light switch. The brake light switch, despite its diminutive size, has a significant function in contemporary automobiles.
If a brake light switch is malfunctioning, many vehicle functions, such as Push-Button Start, Antilock Brakes, and Vehicle Stability Control, will not function.
There are two main purposes for the brake light switch. When a driver depresses the brake pedal, it first activates the brake lights. Second, it informs the car’s computer that the brakes are being used. Driving a car with a broken brake light switch is VERY RISKY.
The brake light switch is typically located just over the brake pedal. It has a one-way or two-way electric switch within. Brake lights that don’t turn on or that stay on all the time are the most typical signs of a broken brake light switch.
A brake light switch: What is it?
Your car’s brake light switch performs a crucial safety duty. How to test it and how to know when to replace it are both covered.
Your car’s brake light switch performs a crucial safety duty. The signal lights at the back of your car receive power when you depress the brake pedal, alerting other cars that you have slowed down.
Why does my dashboard’s brake light remain on?
Don’t risk operating the vehicle if you’ve just started it and you see the brake system warning light on.
To begin with, confirm that the parking brake is fully disengaged. Some automobiles have a combined parking brake and braking system warning light. Make sure your parking brake is fully disengaged by checking it and pulling on the release lever. If the dashboard light is still on, your vehicle’s brake system may be malfunctioning and making it difficult for you to stop. Shut off the engine and make plans to have the car delivered to a reliable repair.
My brake light is on, but my brakes are functioning properly.
Defective Sensors: The parking brake sensor or brake fluid measurement sensors in the brake master cylinder may malfunction, turning on the brake light. A brake repair specialist should be able to recognize the sensor that activated the light and replace it.
Will a brake light come on if there is low brake fluid?
The brake warning light will turn on when the reservoir of brake fluid is low. Your brake fluid level could be low for a number of reasons. Your brake pads may simply be worn out.