Find the tiny odometer button in the instrument panel’s lower left corner. until the service message shows, press and hold. When the message asks “Reset?” release the button, then press and hold it once again.
In This Article...
Is there a way to turn the warning lights back off after replacing the front pads and the sensor? I’ve seen some posts on the 335i, but they don’t appear to apply to the 135i.
I figured it out. I mistakenly believed the cruise control button on the lower stalk to be the odometer reset button. Doh! Basically, turn on the ignition while holding down the odometer reset button until the service option appears after the yellow triangle with the exclamation point on the display. The turn signal selection toggle allows access to the services menu, but it will likely highlight in red the item that needs to be reset first. The display will read reset if you press and hold the BC button on the turn signal for a few seconds.
I recently viewed a YouTube video of a guy demonstrating this material. I’m fairly certain it was in the e90 DIY section. Just tried looking, but I was unsuccessful.
My car has a red front brake indication on (currently at -60miles and counting). If I follow these instructions to try to reset the device, I get to the small spinning clock while holding the BC button, but the device does not reset. With this technique, I can reset/adjust other indicators, but the front pads remain fixed. I essentially get the same outcomes if I attach my BT Scan Tool and perform a condition-based reset (the tool errors trying to reset the front pad indicator, saying something about not being able to talk to the controller).
I don’t have any engine codes, but I did clear the typical fuel pump shadow codes while the tool was connected. No problems there.
My rear brake warning light turned red, but no dealer was required. I recently changed the sensor and restarted the warning. I’ll admit that I had to reset it twice before I realized that the brake warning on the cluster corresponds to the handbrake, but aside than that, everything was OK.
^^ However, this is only accurate if the sensors have actually made contact with the disc. You can reuse your sensors when installing new pads or rotors if you’re proactive and don’t wait for the physical pad sensor alert.
How can I reset the engine management light on my BMW 1 Series?
You will either need to reset the battery by disconnecting the positive and negative connections from the battery for roughly 10 minutes, or you will need to reset the engine management light, also known as the engine control light reset, on the BMW 1 Series. Before you clear the message, make sure you fix all the problems that are causing the inspection light to glow; otherwise, the message will reappear. By connecting the OBD scanner to the automobile and clearing it with it, you can even reset the OBD scanner. Depending on the model and specification, an OBD scanner can cost anywhere between $50 and $100. You can typically rent one at the Car Parts Store for a modest charge if you don’t want to buy one.
Be warned: Do not unplug the battery. BMW electronics are delicate, and when I did so, the BCM’s settings became lost.
Remove the positive and negative cables from the battery to reset the check engine light on the BMW 1, or attach an OBD scanner and perform the reset there.
On a BMW 1 Series, how do you reset the brake warning light?
Can the brake light on a BMW 1 Series be reset? Last week, I had my brakes tested, and new brake pads were put. However, my car’s light is still on.
In less than two minutes, find out if your auto insurance is being overcharged.
Absolutely! Since your brakes have already been inspected, you should feel comfortable turning the brake light back on. The majority of maintenance lights require manual resetting when the task is finished. You must take the following actions to reset the brake light on your BMW 1 Series:
- Press the odometer reset button on your dash after turning the ignition to the ON position.
- Keep pressing the button. A yellow triangle with an exclamation point inside will be seen on your display. The service menu will then appear.
- To discover the brake light setting, use the turn signal stalk.
- To reset the light, press and hold the BC button on your turn signal stalk.
Examine your insurance alternatives with Jerry to make sure you’re prepared financially in case of an accident. The Jerry app, a registered broker that provides end-to-end support, compiles reasonable rates, assists you in switching plans, and even assists you in terminating your old policy.
How can I turn the engine warning light back on?
- As you drive, let the light turn off on its own. None.
- Three consecutive times of starting and stopping the engine None.
- Reconnect the battery after disconnecting it. Wrench.
- Use a code reader for the OBD
What causes my engine warning light to go on?
Depending on the issue, if the check engine light comes on, it may flicker or be on all the time. A issue that requires immediate attention is indicated by a blinking light, or in some cars, a red light instead of a yellow or orange light. In either case, you ought to have the car looked at by a mechanic.
An engine misfire that is severe enough in late-model cars to send unburned fuel into the exhaust system, where it can quickly destroy the catalytic converter and necessitate an expensive repair, is typically indicated by a blinking light. If that occurs, you should turn down the engine and get the automobile or truck checked out as soon as you can.
Even if there is no immediate danger if the light is steady, you should make an appointment as soon as feasible. Even while your fuel mileage may be declining and your vehicle may be spewing unsafe amounts of hydrocarbons and other pollutants, you might not notice a decline in performance since modern automotive systems frequently try to adjust when there is a problem.
According to Jim Collins, a national training team leader for Ford Motor Co., “The customer is really, in the long run, potentially hurting their pocketbook by leaving that light on and ignoring it.” The car’s computer may in some severe circumstances lower power for you in an effort to lessen the likelihood of damage.
Here are some recommendations on what you should do if the check engine light illuminates:
- Search for a critical issue that need quick action. Look for any warning signs of low oil pressure or overheating on your dashboard in the gauges and lights. These circumstances call for you to stop and turn off the engine as soon as you can find a secure location to do so. On some cars, a yellow check engine light indicates troubleshoot, while a red one commands immediate stopping.
- Possibly tighten the gas cap. This frequently makes the issue go away. The light might not reset for a while, so keep that in mind. Some automobiles feature a secondary indicator that sounds when the gas cap is loose.
- Reduce the load and speed. Reduce your speed and make an effort to lessen the demands on the engine if the check engine light is on or you notice any major performance issues, including a lack of power. For instance, it would be wise to put an end to hauling a trailer. Get the car evaluated as soon as you can to avoid costly damage.
- If any built-in diagnostic tools are available, use them. Many contemporary vehicles feature built-in remote diagnostic capabilities that allow for reporting on fault codes and scheduling an appointment for service. Today, numerous automakers offer remote diagnostics and the option to book a service appointment, including Fiat Chrysler, Ford, Hyundai, Jaguar/Land Rover, and Volvo.
How are dash warning lights turned off?
You can start by shutting off the automobile and starting it again. The next step is to unplug your battery, wait a short while, and then plug it back in. Another choice is to keep driving and wait for the light to automatically reset.
How can I reset my BMW now that the battery has been changed?
One of the vehicles with the most advanced intelligent operating system in the world is the BMV. Therefore, the first thing you must do after every hit or replacement of an object in the car is to restart the entire vehicle.
This setup enables the computer to anticipate your next replacement requirement and alert you to it. After changing the battery, resetting the BMW computer is a quick and easy process.
- First, turn on the controller again.
- Step 2: Press “Trip” to activate it and make it light.
- Step 3: Hold down the “trip” button while continuing to press and hold it until the “Reset” button shows up on the screen.
- Reset in Step 4
How do I reset my BMW IDrive?
How do I remove my personal settings and data from my BMW? Select “CAR menu” > Settings > General settings > “Reset vehicle data” on your BMW with Operating System 7 to reset your personal data and settings. Reset car data by choosing “Menu” > “System settings” on your BMW with Operating System 8.
Can I operate a BMW with the check engine light on?
A constant glow normally denotes something less serious, but a check engine light that flashes suggests your car’s engine is seriously damaged and needs quick repair. We strongly advise not operating your BMW while the check engine light is flashing and setting up BMW servicing right away.
Can I manually turn off the check engine light?
You might have requested for assistance with a computer problem if you’ve ever worked in an office setting with an IT department.
Probably the first thing your IT wizard asked was, “Have you tried resetting your computer?”
The analogous repair for a car’s check engine light is the on-off technique. It compels the computer to reboot and restore its previously saved state.
Simply switch the ignition on for 1-2 seconds, then off for 1-2 seconds, using your key. Three or four times through, repeat this step.
If the check engine light is still on after the reset, your car might still be having issues. Think about using the OBD2 scanner to check for the error code or taking your car to a qualified repair.
What causes the dash to have several warning lights?
On the dashboard of the car, the check engine light
Dashboard warning lights are the icons that flash on the dashboard to indicate when the car is having a problem. Although they are intended to glow to indicate a problem with a particular system, there may occasionally be an issue with the warning lights themselves.
Each dash symbol has a specific meaning, therefore it’s crucial to get it checked when it illuminates so you can either fix the issue or ensure the car is secure.
Several lights should turn on when the engine first starts, but they should go out shortly after. When lights remain on after the initial few seconds, they are alerting you that there is a problem with the vehicle.
A dashboard warning light typically does not indicate that the car will break down right away or that it is unsafe to drive nearby, as to a body shop. It’s not advisable to travel long distances when the warning lights are on. The likelihood that the problem may deteriorate and worsen as time goes on increases.
You might be able to determine what your car needs by looking at the warning light. For instance, if your engine’s oil pressure warning light comes on, look up the date of your most recent oil change in your records. Check the oil level under the hood. It could be time to top off or change the oil.
Has the brake system light come on? Check to see if you left the parking brake on first. If this isn’t the case, it’s important to have the brakes checked properly because a car without brakes can be quite dangerous to both passengers inside and outside.
The presence of many dash warning lights could simply indicate that you are experiencing issues with multiple systems.
If several systems were impacted by the collision, there may be several lights on after the incident. If the airbags were deployed during the collision, they must be reset in order for the dash light to not indicate an airbag system malfunction.
However, if all of your lights turn on at once, it can be a sign that your alternator isn’t working properly.
Although the aim of warning lights is to alert you to a potential issue, it is not always obvious what the issue is at first. It is essential to have the car analyzed by a trained collision repair professional.
The sooner you take care of it, the less probable it is that there will be significant harm.