1. Fill up all tires to the recommended pressure on the tire placard.
2. With the engine off, set the ignition to the ON/RUN position.
3. Choose Settings or Vehicle Info with the help of the iDrive controller.
4. Choose the Vehicle, Vehicle/Tires, or Vehicle Status option.
5. Choose from Perform Reset, Reset TPM, or TPM.
Start the engine, choose Reset, and then click Yes.
7. Select the media button on the center console.
8. To complete retraining, vehicle must be driven for up to 10 minutes at a speed of 25 MPH or higher.
Learn Again Procedure for Models Without iDrive:
2. Turn the ignition on.
3. Adjust the turn signal toggle switch such that the REST and TPMS indicators are visible.
4. Depress the button at the lever’s tip to activate the turn signal.
5. Hold down the button at the end of the turn signal lever while pressing it until RESETTING or a checkmark appears on the screen.
6. To complete retraining, vehicle must be driven for up to 20 minutes at a speed of 20 MPH or higher.
Models without iDrive must follow the relearn procedure (only some models):
3. When the TPMS light appears on the gauge cluster, press and hold the TPMS Reset button (behind the hazards switch or in front of the gear selector).
4. To complete retraining, vehicle must be driven for up to 20 minutes at a speed of 20 MPH or higher.
In This Article...
For iDrive
- Always adjust the tire pressure as directed by the tire placard.
- without starting the vehicle, turn the ignition.
- To access the primary menu, click the MENU button.
- Using the Drive controller, navigate to the VEHICLE INFO page.
- the VEHICLE STATUS option
- Choose RESETTPM.
- Don’t drive your automobile, but start the engine nonetheless
- Use “RESETTPM” to begin the initialization process.
- Use the vehicle.
How can a tire pressure monitoring system be reset?
When the tire pressure light blinks three times, release pressure on the TPMS reset button. Start the car and let it run for 20 minutes to let the sensor reset. Under the steering wheel is normally where you’ll find the reset button for the tire pressure monitor. If you can’t find it, consult the owner’s manual for your vehicle.
On a BMW 328i, how do you check the tire pressure?
- Instead of shortly after the car has been driven, check the tire pressure in your BMW when the tires are cold.
- Remove the valve stem cap and store it safely by unscrewing it.
- Press down firmly on the valve stem with a tire gauge while doing so.
- The PSI will be shown on the gauge.
- Take away the gauge
Can the BMW tire pressure monitoring system be turned off?
My incoming F30 will most likely feature TPMS pressure sensors, but since the winter wheels I purchased don’t have the sensors, can I disable the pressure monitoring system to avoid seeing an error message on the dash?
It won’t cost much more to add TPMS to each wheel, therefore you’ll need to pay the extra money. Not in my experience, at least. You may just take the TPMS from your old wheels and install it on your new ones if you’re getting rid of your stock wheels totally.
In the winter, I operate my winters without sensors. Nothing to worry about. I simply need to press the iDrive wheel during startup to acknowledge that the issue has been identified.
I had assumed that there would merely be an error, which would be bad enough, but pressing the idrive button each time I got into the car would be quite annoying! I’m hoping the fuse trick works flawlessly!
I don’t mind the double-press for the TPMS warning because you already have to press the iDrive on startup to accept the warning.
If pressing a button bothers you, the cost actually is not a huge deal because I was able to purchase secondhand OEM sensors for my 19’s for under $200.
According to what I can see for UK models, it isn’t even optioned. Wheel swapping is not a problem if you have the regular UK fit TPWS because we don’t have wheel sensors.
How much pressure should a BMW 328i’s tires be at?
Although 32 PSI (pounds per square inch) is the generally accepted tire pressure for BMW models, you should always check the details for your car. Consult your owners handbook or the sticker on the inside edge of the driver-side door for more information.
Why, when my tires are fine, BMW, is the tire pressure light on?
What it means: Your vehicle’s tire pressure will be too low and the BMW tire pressure monitoring system (TPMS) will notify you. When air pressure is 25% below the usual suggested pressure for your BMW model, the warning light turns on. Low tire pressure could put your BMW at danger for tire failure, excessive tire wear and tear, handling issues, and decreased fuel efficiency.
What to do if it comes on: Turn off your car and check the pressure in each tire if the TPMS light comes on when you start it. Ensure that the tires are inflated to the optimum pressure. The recommended tire pressure is printed in your owner’s handbook or on a placard inside the driver-side door of your car.
Find a gas station with air pumps, check the tire pressure, and add air as necessary if the TPMS indicator illuminates while you are driving. The TPMS light will also come on if your tire suddenly flattens as a result of damage. Pull over right away and inspect your tires if you see this light and experience a difference in how your car handles. Many BMW automobiles come with run-flat tires already mounted from the manufacturer with no spare tire. If so, move cautiously to a BMW service center in the area. You will need to hire a tow truck if you have fitted aftermarket tires that are not run flats.
It often denotes a TPMS malfunction if the indicator glows and flashes. The first step is to check the pressure in each of your tires once more and add air if needed. Your best option is to take it to a qualified BMW mechanic for diagnosis if the TPMS light is still on after adding air.
Note: Extreme weather changes can have an impact on tires, particularly in the colder winter months. It’s a good idea to inspect your tires each month.
What actions are required to turn off the light: If your tire pressure is too low, you should fill them up with air and then reset your TPMS (see the directions in your owner’s manual to do this). If this doesn’t work, you’ll need to visit your local BMW repair shop for an accurate diagnosis.
Where is the location of the tire pressure sensor?
Tire pressure sensors are undoubtedly found close to the tires themselves. But precisely where are they situated? There is a tiny gap between the wheel and the tire when a pressure tire is mounted to the wheel. The sensor is situated in this area. It can maintain consistent touch with the tire thanks to its placement, which is essential if you want to acquire accurate readings on the condition of your tires. The sensor, however, is firmly fastened to the wheel. This guarantees safety and stability, even while driving aggressively.
How inflated should my BMW tires be?
To ensure a safe ride, you should check the tire pressure on your BMW. Although 32 PSI (pounds per square inch) is the recommended tire pressure for most BMW models, you should always double-check by examining the sticker on the inside edge of the driver’s door.
Why won’t my tire pressure warning light turn on?
If your tires are properly inflated yet the warning light continues to illuminate, you may have a leak or a TPMS issue in one or more of your tires. To determine if a tire has a leak is not difficult. Simply double-check the air pressure in each of your tires with your tire gauge. If all of the tires have the proper air pressure, one or more tire pressure sensors are likely to be at fault, necessitating repair work on your tire pressure monitoring system. You’ll need to replace or repair the tire if you notice that one or more of your tires’ air pressures have fallen.
Why do my car’s tires still have low pressure?
Don’t ignore the tire-pressure warning light if it turns on; you might be getting a flat. A tire’s tendency to lose around a pound of air pressure every month and a pound for every 10 degrees of temperature drop can cause low pressure, as can leaks.
When is the TPM on a BMW 328i reset?
When the tire pressure light blinks three times, release pressure on the TPMS reset button. To allow the sensors to reset, start the automobile and let it run for 20 minutes.
How much does a BMW TPMS sensor replacement cost?
Best in Automotive Repair Replacement tire pressure monitor control modules for BMW 328i models typically cost between $597 and $661. Between $245 and $309 is projected to be the cost of labor, while $352 is the cost of the parts.
Should the TPMS be reset after purchasing new tires?
After changing or rotating your tires, or after adding new sensors, you should always reset your TPMS. Even after you have inflated your tires, some sensor manufacturers advise restarting the device. By teaching the primary TPMS system to identify the sensors in their new locations, resetting the TPMS is frequently referred to as retraining the system. TPMS reset procedures vary from vehicle to vehicle and typically involve a specific sequence of ignition and pedal actions, a configuration change in your dashboard menu, or the use of a TPMS Reset Tool.
Why does the light on my tire stay on?
When the TPMS warning light illuminates, proceed with caution. This indicates that at least one of your tires may be at least 25% under-inflated.
*The simplest way to get the most accurate reading is to check the tire pressure before you drive on it when the tire is “cool.” If your TPMS light is on, first check that you have correctly reset your TPMS by following these instructions.
Will my TPMS light automatically turn off if I fill my tires with air after it illuminates?
Several minutes after reinflating the tires to the prescribed pressure, the TPMS light ought to go out.
What happens if I adjust the tire pressure but the light on my tire pressure gauge still doesn’t go out?
The only place that can fix a computer issue that causes the TPMS warning light to turn ON and flash ON for one second and OFF for three seconds is the dealership service center. When the TPMS warning light illuminates and remains on, one or more tires may have low tire pressure. The light ought to go out once the tire is inflated to the recommended tire pressure listed on the door placard. Always check the pressure in all of your tires because one or more of them may not be at the proper pressure.
Is 40 psi too much pressure for tires?
For some vehicles with specs within this range, a pressure of 40 psi may be suitable. But for some other tires, this number can likewise be too high or too low.
For example, sports automobiles or passenger cars may be suitable with a pressure level of 40 psi. However, this is too low for heavy trucks and below the recommended pressure of 35 psi for small cars.
The recommended pressure range for tires on well-known sports cars and passenger vehicles is 32 to 40 psi. Depending on the type of vehicle, a specific index will be given. It should be noted that this level is suggested while the tire is cold, so after a lengthy trip, you must check it again to ensure proper adjustment.
There are many various car models available today, and each will utilize a different type of tire. Therefore, the manufacturer will decide in advance what pressure should be used in each of these tires.
It is your responsibility to maintain the best level for the car to run safely and smoothly. To find out whether or not this 40 psi pressure level is good for your car, you must first verify the tire specifications.