New brakes and some standard maintenance were performed on my automobile. The mechanic informed me that the brake light should go off on its own soon, but I noted it was still on. The caution light has been on for a couple hours now. Can I do it myself to reset the brake light on a BMW X5?
In less than two minutes, find out if your auto insurance is being overcharged.
Don’t worry, resetting the brake light on your BMW X5 is easy and doesn’t require any special tools. The brake light is meant to reset automatically when the brakes and brake wear sensors are replaced.
A BMW X5’s brake light should be reset by:
- Don’t start the engine after turning the ignition on.
- Up until the service menu appears, keep holding down the trip reset or odometer button. The service menu should show after holding the button down for five to ten seconds. The button is normally located on the left side of the instrument cluster.
- To find the brake warnings, use the reset button or, depending on the model, the controls on the turn signal lever to navigate through the settings.
- When a popup appears asking you if you’d like to reset the warning, press and hold the reset button or BC button on the end of the turn signal lever.
- Once the display indicates that it is resetting, press the reset or *BC** button and, if prompted, confirm reset.
Additionally, it sounds like you keep a decent plan for routine auto maintenance, but as we all know, any work done on your BMW will be expensive. Use Jerry if you want to cut costs and make sure you aren’t paying too much for your auto insurance.
Jerry is a free insurance comparison software that checks around for the best deals with more than 50 different insurance providers. You may make adjustments at any time, receive prices instantly, and text an agent with any queries you may have.
In This Article...
How to reset the brake light on a BMW using method 1
- Start the ignition, but don’t let the vehicle go. Press the START button if your BMW has one without depressing the brake pedal.
- Verify sure the time is shown in the instrument cluster’s center.
- The ODO reset button should be pressed and held for 5 seconds. On the dashboard, a yellow triangle will first show. Hold the ODO reset button down until the subsequent symbol appears.
- When the front or rear brake sign appears, repeatedly press the ODO reset button. Depending on the sensor you wish to replace and reset.
- Press and hold the ODO reset button until the word RESET appears below the desired brakes symbol when it appears on the screen.
- Press the button once more once the word “reset” appears beneath the brake symbol. Holding the ODO reset button down will cause the brake symbol to vanish.
- The mileage ought to become zero, indicating that the reset was completed. You will have 25,000 miles for the front brakes and 31,000 miles for the rear brakes before your BMW brakes need to be changed again. Although these intervals could differ from one model to another.
How can I reset the BMW’s brake pad lights?
Check Out These Steps to Reset Your Brake Warning Light the ignition with the key (or key fob). While turning the key to position 2, avoid turning on the ignition. Open the driver’s door and hold it open for around ten seconds. The brake pad lights ought to reset once you’ve finished the aforementioned three steps.
Why does my BMW x5 have a brake light?
Bad Switch: A faulty or failed switch is a typical cause of the Parking Brake light remaining on. You may quickly verify this by jiggling the handle once it has been lowered. The switch is most likely to be the problem and needs to be replaced if the light goes out (or goes out and comes back on).
If the brake handle is not fully down, there is another factor that could cause the light to remain on. Verify again that the parking brake is released and that the handle is fully lowered. The light will remain on if the parking brake cable is under any stress.
Parking Brake Not Disengaging: Occasionally, the parking brake itself is the source of the issue rather than the switch or the wires. The dash warning light will remain on if the brake does not release when the handle is dropped.
Low Brake Fluid: Your Parking Brake light is a multipurpose device that is intended to turn on when the reservoir’s fluid level falls below a specific level. As the fluid level fluctuates, you might see the light turning on or off when making turns.
The brake fluid level sensor in your master cylinder is malfunctioning. It is sometimes integrated into the reservoir cap, and other times it is positioned on the side of the sensor. The Parking Brake light will come on if the sensor malfunctions or becomes faulty.
Uneven Fluid Pressure: If your automobile has uneven brake fluid pressure in one or more lines, it may influence how well it can stop and may even cause it to pull to one side or the other. The parking brake light in your dash can also be activated by it.
On a BMW 2020, how do you reset the brake sensor?
My car’s brakes were recently changed by my uncle, but the warning light is still on. Does a BMW X3 have a mechanism to reset the brake light?
Every time the brakes and brake wear sensors are replaced on a BMW X3, the brake light warning must be reset. Fortunately, the brake light reset is simple and should only take a few minutes.
Resetting the brake light on a BMW X3 is made simple by:
- Do not start the engine after turning the ignition to the on position.
- Wait 30 seconds before opening the driver’s side door.
- Wait another 30 seconds after switching the ignition to the off position.
- start the vehicle
If the aforementioned fails, you should:
- Up until the service menu appears, keep holding down the trip reset or odometer button. The service menu should show after holding the button pressed on the left side of the speedometer for approximately ten seconds.
- When prompted to reset the warning, press and hold the reset or BC button on the end of the turn signal lever.
- When prompted, press the reset or BC button once the screen indicates that it is resetting.
Finding auto insurance shouldn’t be a headache, but dealing with unnecessary warning lights can be.
Jerry is a helpful software that compares quotes from more than 50 leading insurance companies in a couple of seconds. When you locate an insurance you prefer, Jerry can assist with the transition and paperwork. It’s that simple!
After replacing my brake pads, why is my brake light still on?
Your parking brake is engaged if that light is on. When the parking brake is released yet the light remains on, low brake fluid is the cause. If the fluid is full and the light is still on, there can be an issue with the booster or hydraulic system.
What does the BMW’s yellow brake light signify?
I continually receiving a triangle on my dash with an exclamation point and a yellow brake light. It randomly starts up and then shuts off. They topped out the brake fluid after I took it to the dealership to have it checked. but it’s now turning back on. Anyone with knowledge of the issue? thanks.
So, since the dealer filled it off, have you checked the brake fluid level again? You may have a brake system leak if your braking system required enough fluid to trigger the low brake fluid light. How does the pedal feel? When you apply consistent pressure, does it sag at all? When you overnight park, are there any moist areas close to the inside of the wheels?
I didn’t check the amount of the brake fluid. How can I go about doing that? Normally, the pedal feels. Lighting turns on and off. I therefore assume it is the sensor.
There is a sizable black plastic cover on the driver’s side beneath the hood, just where the gas strut—which keeps the hood up—attaches to the body. Both a front and a back clip are present. The brake fluid reservoir can be seen there if you lift it off.
Although I too prefer my eyeballs to any fluid level sensors (crankcase sump?! ), a YELLOW brake indication, according to the table in the non-iDrive handbook, indicates that the brakes are engaged “Drive-off assistant is not working. After the brake is disengaged, the car won’t be kept in position.” A red sign would be low fluid.
How can I turn off the dashboard brake light?
RISK: Despite changing the brake pads and associated wear sensors, the dashboard braking system warning light continues to flicker. Steps to take:
- To check that the brake pads and discs are in contact, repeatedly press the brake pedal.
- Turn off the dashboard for a brief period of time.
- Check to check if the light is still on after turning on the dashboard once again. Ask for help and guidance if the brake warning light is still on.
Only for entertainment and informational reasons, the information in this article should not be used as a substitute for consulting a qualified technician or mechanic for expert guidance. We advise you to speak with a licensed technician or mechanic if you have any specific queries or issues regarding any of the subjects discussed here. We will not, under any circumstances, be held responsible for any loss or harm resulting from your reliance on any content.
I have a brake pad warning light on. Can I drive?
Driving is safe when this light is on for a brief period of time. As was already indicated, when you still have some brake pad material remaining, the light will turn on. However, if you wait too long and keep driving, you will run out of material and harm the rotors. Waiting too long is hazardous and raises the likelihood of being involved in an accident because the brakes won’t stop the car as quickly without any pad material.
As always, if you have any problems with your brakes or wear indicators, our qualified specialists are here to help.
BMW brake sensor replacement necessary?
The “brake” light on your dashboard or iDrive system is controlled by your BMW brake pad sensor, which also informs you of the remaining life of your brake pads. The sensor is mounted to the brake pad; as soon as the brake pads are completely worn down, the sensor’s tip breaks, tripping the wire and turning on the dashboard light. The brake pad sensor error codes are as follows when using an OBD scanner:
5, 5, 6, 5, 14, 5, 15, and 6F12
Every time you change your brake pads, you should also replace the brake pad sensor. The sensor does not need to be changed every time, but failing to do so could lead to erroneous readings of the amount of life left in your pads and a persistent notification on your dash/iDrive system. The only way to get rid of the light once it appears on the dash is to either swap out the sensor or bypass it, which will stop it from reading the pad life.