Hi there, We haven’t been around much because our f11 520d has been a good friend and all-around wonderful vehicle.
Can I reset using an iDrive or an OBD scanner from eBay? If the latter, any recommendations on which to choose?
I think the service light can be turned off by pressing and holding the button in the left-hand corner of the instrument cluster while the engine is running until the service items are shown. Press the button to cycle through the various services until you come to the service indicator you wish to reset. Once it says “reset,” release the button and press and hold once again to restart the light. I hope that’s accurate.
Hey, thanks for that! I navigated the menu to the reset process and pressed reset; the timer appeared, but the message “reset failure” appeared next. Darnit. I doubt it, however it’s possible that the new sensor isn’t attached properly. Other explanations?
No issue, I wonder if you attempt the reset procedure again after locking the car and letting it idle for a while (until the engine start button light turns off). Although it is improbable, as you point out, that the sensor is improperly attached, it can happen, so you can inspect it if you choose.
Hi, I apologize if this is a bit late, but I do hope that this will be somewhat helpful. After countless agonizing tries and numerous “reset failure” signs, I was finally able to reset my rear brake sensor by using the same techniques as everyone else, with the exception of one minor modification: I disengaged the electronic handbrake first. first time it worked. We appreciate the previously provided information.
I replaced the front and rear pads on my F11 on Wednesday, and I did this through the dashboard. Both seemed to operate after I had drove the car for a while, rather than in the garage after I had dropped the car once more. It also took three or four attempts to reset each.
Could someone kindly provide a very clear explanation on how to “reset” the brake warning light as I’m new to this type stuff? Despite reading, I still don’t fully understand the entire process. I drive a 2014 528Xi. If it makes a difference, that is.
In This Article...
Questions and Answers
- The BMW brake light won’t reset; why?
- After you reset the front or rear brake pads, you must carry out the BMW brake light reset process. The brake wear sensor should also be changed, if possible. You might not be able to reset the brake light if the brake wear sensor was damaged during installation in some circumstances.
- Which BMW models are compatible with these instructions?
- The methods described above are compatible with a wide range of BMW models, including the E30, E90 F30 F10, E39 E83 E92 E70 E87 E93 E92 E30 E36 E38 E34, etc.
How can I reset the BMW’s brake pad lights?
Check Out These Steps to Reset Your Brake Warning Light the ignition with the key (or key fob). While turning the key to position 2, avoid turning on the ignition. Open the driver’s door and hold it open for around ten seconds. The brake pad lights ought to reset once you’ve finished the aforementioned three steps.
On a BMW x5, how do you turn off the brake light?
New brakes and some standard maintenance were performed on my automobile. The mechanic informed me that the brake light should go off on its own soon, but I noted it was still on. The caution light has been on for a couple hours now. Can I do it myself to reset the brake light on a BMW X5?
In less than two minutes, find out if your auto insurance is being overcharged.
Don’t worry, resetting the brake light on your BMW X5 is easy and doesn’t require any special tools. The brake light is meant to reset automatically when the brakes and brake wear sensors are replaced.
A BMW X5’s brake light should be reset by:
- Don’t start the engine after turning the ignition on.
- Up until the service menu appears, keep holding down the trip reset or odometer button. The service menu should show after holding the button down for five to ten seconds. The button is normally located on the left side of the instrument cluster.
- To find the brake warnings, use the reset button or, depending on the model, the controls on the turn signal lever to navigate through the settings.
- When a popup appears asking you if you’d like to reset the warning, press and hold the reset button or BC button on the end of the turn signal lever.
- Once the display indicates that it is resetting, press the reset or *BC** button and, if prompted, confirm reset.
Additionally, it sounds like you keep a decent plan for routine auto maintenance, but as we all know, any work done on your BMW will be expensive. Use Jerry if you want to cut costs and make sure you aren’t paying too much for your auto insurance.
Jerry is a free insurance comparison software that checks around for the best deals with more than 50 different insurance providers. You may make adjustments at any time, receive prices instantly, and text an agent with any queries you may have.
After replacing my brake pads, why is my brake light still on?
Your parking brake is engaged if that light is on. When the parking brake is released yet the light remains on, low brake fluid is the cause. If the fluid is full and the light is still on, there can be an issue with the booster or hydraulic system.
How can I turn off the dashboard brake light?
RISK: Despite changing the brake pads and associated wear sensors, the dashboard braking system warning light continues to flicker. Steps to take:
- To check that the brake pads and discs are in contact, repeatedly press the brake pedal.
- Turn off the dashboard for a brief period of time.
- Check to check if the light is still on after turning on the dashboard once again. Ask for help and guidance if the brake warning light is still on.
Only for entertainment and informational reasons, the information in this article should not be used as a substitute for consulting a qualified technician or mechanic for expert guidance. We advise you to speak with a licensed technician or mechanic if you have any specific queries or issues regarding any of the subjects discussed here. We will not, under any circumstances, be held responsible for any loss or harm resulting from your reliance on any content.
What does the BMW’s yellow brake light signify?
I continually receiving a triangle on my dash with an exclamation point and a yellow brake light. It randomly starts up and then shuts off. They topped out the brake fluid after I took it to the dealership to have it checked. but it’s now turning back on. Anyone with knowledge of the issue? thanks.
So, since the dealer filled it off, have you checked the brake fluid level again? You may have a brake system leak if your braking system required enough fluid to trigger the low brake fluid light. How does the pedal feel? When you apply consistent pressure, does it sag at all? When you overnight park, are there any moist areas close to the inside of the wheels?
I didn’t check the amount of the brake fluid. How can I go about doing that? Normally, the pedal feels. Lighting turns on and off. I therefore assume it is the sensor.
There is a sizable black plastic cover on the driver’s side beneath the hood, just where the gas strut—which keeps the hood up—attaches to the body. Both a front and a back clip are present. The brake fluid reservoir can be seen there if you lift it off.
Although I too prefer my eyeballs to any fluid level sensors (crankcase sump?! ), a YELLOW brake indication, according to the table in the non-iDrive handbook, indicates that the brakes are engaged “Drive-off assistant is not working. After the brake is disengaged, the car won’t be kept in position.” A red sign would be low fluid.
How are BMW control messages reset?
Find the tiny odometer button in the instrument panel’s lower left corner. until the service message shows, press and hold. When the message says “Reset,” let go of the button and press and hold it once more.
I have a brake pad warning light on. Can I drive?
Driving is safe when this light is on for a brief period of time. As was already indicated, when you still have some brake pad material remaining, the light will turn on. However, if you wait too long and keep driving, you will run out of material and harm the rotors. Waiting too long is hazardous and raises the likelihood of being involved in an accident because the brakes won’t stop the car as quickly without any pad material.
As always, if you have any problems with your brakes or wear indicators, our qualified specialists are here to help.
Why does my dashboard’s brake light remain on?
Don’t risk operating the vehicle if you’ve just started it and you see the brake system warning light on.
To begin with, confirm that the parking brake is fully disengaged. Some automobiles have a combined parking brake and braking system warning light. Make sure your parking brake is fully disengaged by checking it and pulling on the release lever. If the dashboard light is still on, your vehicle’s brake system may be malfunctioning and making it difficult for you to stop. Shut off the engine and make plans to have the car delivered to a reliable repair.
BMW brake sensor replacement necessary?
The “brake” light on your dashboard or iDrive system is controlled by your BMW brake pad sensor, which also informs you of the remaining life of your brake pads. The sensor is mounted to the brake pad; as soon as the brake pads are completely worn down, the sensor’s tip breaks, tripping the wire and turning on the dashboard light. The brake pad sensor error codes are as follows when using an OBD scanner:
5, 5, 6, 5, 14, 5, 15, and 6F12
Every time you change your brake pads, you should also replace the brake pad sensor. The sensor does not need to be changed every time, but failing to do so could lead to erroneous readings of the amount of life left in your pads and a persistent notification on your dash/iDrive system. The only way to get rid of the light once it appears on the dash is to either swap out the sensor or bypass it, which will stop it from reading the pad life.
When the red brake light is on, can you drive?
Your car’s brakes enable you to stop safely, especially in an emergency. You should pay attention and get in touch with your repair right away if your brake warning light illuminates. Since your car’s brakes are the most crucial safety element, you shouldn’t drive if they aren’t functioning properly.
When you notice that your brake warning light is on, keep an eye out for the following:
The need to replace a brake is one of the primary causes for the Brake Warning Light to illuminate. The light only indicates that one of the brakes is failing; it does not specify which brake it is. Your brakes can be examined by a mechanic who will also be able to identify which one needs to be replaced.
Other causes for your brake warning light to illuminate include low brake fluid or damaged brake pads. Your brake fluid may occasionally need to be replenished or additional fluid may need to be added if the level is low. In other circumstances, a qualified mechanic can totally replace the brake pads for you.
Another potential cause for the Brake Warning Light to illuminate is leaking brakes. The car won’t be able to stop if the brakes are leaking. Your car should not be operated in this hazardous situation. Contact a professional right away to get your automobile evaluated if you believe there is a leak and your brake warning light is on.
It’s crucial to notify your mechanic if you experience strange noises when applying the brakes and your brake warning light is on. Grinding noises are particularly dangerous since they indicate that your brake pads need to be replaced right away because they are worn out.
The warning light and the car pulling to one side while you apply the brakes are other indicators that your brakes need to be replaced. This may indicate a brake fluid leak or the necessity for brake replacement.
It is unsafe to drive while the brake warning light is illuminated. It implies that your brakes aren’t functioning properly and should be fixed right now. YourMechanic or any qualified mechanic should inspect your braking system as soon as you observe the Brake Warning Light illuminated.