- Start the ignition, but do not drive. Press the START button if your BMW has one without depressing the brake pedal.
- Ensure that the time is displayed in the instrument cluster’s center.
- The ODO reset button should be pressed and held for roughly five seconds. The dash will first display a yellow triangle. Hold the ODO reset button down until the subsequent symbol appears.
- When the symbol for the front or rear brakes appears, repeatedly press the ODO reset button. Depending on the sensor you want to reset after replacing.
- When the preferred brakes’ symbol appears on the screen, press and hold the ODO reset button until the word “RESET” appears beneath the symbol.
- Release the button immediately when the word “reset” appears beneath the brake symbol, then press the button once again. Holding the ODO reset button down will make the brake light go out.
- The kilometers should become —–, signifying that the reset was successful. Although these intervals may vary between models, the next time you should have your BMW brakes changed is at 25000 miles for the front brakes and 31000 miles for the rear brakes.
In This Article...
tiphu
I recently bought brake sensors, pads, and rotors for my father’s car, and I was wondering how to reset the brake light that illuminates when the brakes are needed. By keeping the car in the on or acc position and depressing the brake pedal, I am certain that it can be done without a rest tool. I’ve seen it done, but I’m not sure of the order.
Same issue here, so I simply reset it. To turn the key off, leave the driver door open and insert the key in position 1 of the ignition for around 30 seconds, or until the warning brake light illuminates. When you insert the key again, the brake line warning goes away.
On a BMW, how do you turn off the brake light?
Can the brake light on a BMW 1 Series be reset? Last week, I had my brakes tested, and new brake pads were put. However, my car’s light is still on.
In less than two minutes, find out if your auto insurance is being overcharged.
Absolutely! Since your brakes have already been inspected, you should feel comfortable turning the brake light back on. The majority of maintenance lights require manual resetting when the task is finished. You must take the following actions to reset the brake light on your BMW 1 Series:
- Press the odometer reset button on your dash after turning the ignition to the ON position.
- Keep pressing the button. A yellow triangle with an exclamation point inside will be seen on your display. The service menu will then appear.
- To discover the brake light setting, use the turn signal stalk.
- To reset the light, press and hold the BC button on your turn signal stalk.
Examine your insurance alternatives with Jerry to make sure you’re prepared financially in case of an accident. The Jerry app, a registered broker that provides end-to-end support, compiles reasonable rates, assists you in switching plans, and even assists you in terminating your old policy.
What does the BMW’s yellow brake light signify?
I continually receiving a triangle on my dash with an exclamation point and a yellow brake light. It randomly starts up and then shuts off. They topped out the brake fluid after I took it to the dealership to have it checked. but it’s now turning back on. Anyone with knowledge of the issue? thanks.
So, since the dealer filled it off, have you checked the brake fluid level again? You may have a brake system leak if your braking system required enough fluid to trigger the low brake fluid light. How does the pedal feel? When you apply consistent pressure, does it sag at all? When you overnight park, are there any moist areas close to the inside of the wheels?
I didn’t check the amount of the brake fluid. How can I go about doing that? Normally, the pedal feels. Lighting turns on and off. I therefore assume it is the sensor.
There is a sizable black plastic cover on the driver’s side beneath the hood, just where the gas strut—which keeps the hood up—attaches to the body. Both a front and a back clip are present. The brake fluid reservoir can be seen there if you lift it off.
Although I too prefer my eyeballs to any fluid level sensors (crankcase sump?! ), a YELLOW brake indication, according to the table in the non-iDrive handbook, indicates that the brakes are engaged “Drive-off assistant is not working. After the brake is disengaged, the car won’t be kept in position.” A red sign would be low fluid.
My electronic parking brake has to be reset.
Once the ignition is turned off, the Honda Civic’s electric parking brake is intended to activate. This is how to reset it:
- Place the gear lever in PARK and turn the ignition to the ON position. Refrain from applying the brakes.
- The EPB button must be pulled and then released to engage the electric parking brake.
- When you hear a mechanical sound, pull and hold the EPB button for a few seconds before letting go.
- When you hear two mechanical beeps, pull up on the EPB button and keep it there for three seconds before releasing it.
The electric parking brake is fully reset to engage each time the ignition is turned off.
Repeat the process outlined above to disable this function; the system will indicate your success with a simple click.
How can I turn off the dashboard brake light?
RISK: Despite changing the brake pads and associated wear sensors, the dashboard braking system warning light continues to flicker. Steps to take:
- To check that the brake pads and discs are in contact, repeatedly press the brake pedal.
- Turn off the dashboard for a brief period of time.
- Check to check if the light is still on after turning on the dashboard once again. Ask for help and guidance if the brake warning light is still on.
Only for entertainment and informational reasons, the information in this article should not be used as a substitute for consulting a qualified technician or mechanic for expert guidance. We advise you to speak with a licensed technician or mechanic if you have any specific queries or issues regarding any of the subjects discussed here. We will not, under any circumstances, be held responsible for any loss or harm resulting from your reliance on any content.
On a BMW, how do you reset the red exclamation mark?
Start the engine, then move through the obc until you find the word RESET next to the “flat tyre” sign. To choose, press the stalk’s tip. A tick should display after about 5 seconds of pressing and holding; just drive away, and it will reset itself. Don’t wait for any confirmation because there are no other signs that it has done it.
All owners and aficionados of BMW’s 1 and 2 series have their own forum community. Join the conversation regarding performance, customizations, classifieds, troubleshooting, maintenance, and more!
My parking brake light won’t turn on; why?
A number of dashboard warning lights may suddenly begin to illuminate. Everyone is aware of the functions of the battery and oil lights, but many other lights call for consulting the owner’s manual. To assist make things a little clearer, we’ll look at several lights and what they represent in the upcoming months.
The parking brake warning light is displayed here. It can be either red or orange, depending on the brand of the car. It flashes to indicate that the parking brake or emergency brake is applied and needs to be disengaged before moving on with a drive.
It indicates that you need to add brake fluid if it stays lit after the parking brake is released or if it flashes intermittently while you’re driving. You must get the braking system checked if you check the fluid, add as necessary, and the light doesn’t go out.
In fact, you should get a brake inspection regardless of whether there is a leak in your brake system. Why? As your brake shoes or pads deteriorate, more fluid is needed to press them against the rotors or drums to stop the car. This dashboard light can be gently alerting you that brake servicing and repairs are about due.
The parking brake needs maintenance if there is an illuminated wrench under the light. The car can be operated safely, but it needs to see a mechanic.
Is your parking brake in need of repair? Go to any of the nine Auto Select auto and truck repair shops in Appleton, Green Bay, Stevens Point, and Weston (Wausau).
With the brake light on, can I drive?
When you start your car, if the brake warning light illuminates and stays on, do not drive. Turn off your vehicle, then look for potential reasons of the problem (we will get to those soon).
Do not become alarmed if the brake warning light illuminates while you are driving or in traffic. There are multiple hydraulic braking systems in your car. So, even though it could take a little longer than usual to stop completely, pull over securely and arrange to have your car towed to your house or to a reputable technician for an inspection.
Once more, it’s crucial to avoid continuing to drive while the brake light is on as this could further harm your braking system and be quite dangerous.
*Pro Tip: All of the dashboard lights should come on when you switch on your car. If one or more of them are not turning on, there might be an issue with that particular indicator.
Where is the switch for the brake lights?
A little gadget connected to the brake pedal mechanism is called a brake light switch. The brake light switch, despite its diminutive size, has a significant function in contemporary automobiles.
If a brake light switch is malfunctioning, many vehicle functions, such as Push-Button Start, Antilock Brakes, and Vehicle Stability Control, will not function.
There are two main purposes for the brake light switch. When a driver depresses the brake pedal, it first activates the brake lights. Second, it informs the car’s computer that the brakes are being used. Driving a car with a broken brake light switch is VERY RISKY.
The brake light switch is typically located just over the brake pedal. It has a one-way or two-way electric switch within. Brake lights that don’t turn on or that stay on all the time are the most typical signs of a broken brake light switch.
My brake light is on, but my brakes are functioning properly.
Defective Sensors: The parking brake sensor or brake fluid measurement sensors in the brake master cylinder may malfunction, turning on the brake light. A brake repair specialist should be able to recognize the sensor that activated the light and replace it.
Are new BMW brake sensors required?
The “brake” light on your dashboard or iDrive system is controlled by your BMW brake pad sensor, which also informs you of the remaining life of your brake pads. The sensor is mounted to the brake pad; as soon as the brake pads are completely worn down, the sensor’s tip breaks, tripping the wire and turning on the dashboard light. The brake pad sensor error codes are as follows when using an OBD scanner:
5, 5, 6, 5, 14, 5, 15, and 6F12
Every time you change your brake pads, you should also replace the brake pad sensor. The sensor does not need to be changed every time, but failing to do so could lead to erroneous readings of the amount of life left in your pads and a persistent notification on your dash/iDrive system. The only way to get rid of the light once it appears on the dash is to either swap out the sensor or bypass it, which will stop it from reading the pad life.