- Start the ignition, but do not drive. Press the START button if your BMW has one without depressing the brake pedal.
- Ensure that the time is displayed in the instrument cluster’s center.
- The ODO reset button should be pressed and held for roughly five seconds. The dash will first display a yellow triangle. Hold the ODO reset button down until the subsequent symbol appears.
- When the symbol for the front or rear brakes appears, repeatedly press the ODO reset button. Depending on the sensor you want to reset after replacing.
- When the preferred brakes’ symbol appears on the screen, press and hold the ODO reset button until the word “RESET” appears beneath the symbol.
- Release the button immediately when the word “reset” appears beneath the brake symbol, then press the button once again. Holding the ODO reset button down will make the brake light go out.
- The kilometers should become ——-, signifying that the reset was successful. Although these intervals may vary between models, the next time you should have your BMW brakes changed is at 25000 miles for the front brakes and 31000 miles for the rear brakes.
In This Article...
On a 2011 BMW 328i, how do you turn off the brake light?
Check Out These Steps to Reset Your Brake Warning Light the ignition with the key (or key fob). While turning the key to position 2, avoid turning on the ignition. Open the driver’s door and hold it open for around ten seconds. The brake pad lights ought to reset once you’ve finished the aforementioned three steps.
Why is my BMW 328i’s brake light on?
The brake warning light is a major matter. When you see it turn on, ensure sure your emergency brake is not engaged, then halt your vehicle as soon as you can. Your brakes could not operate at all if you have insufficient brake fluid.
On a BMW, how do you turn off the brake light?
Can the brake light on a BMW 1 Series be reset? Last week, I had my brakes tested, and new brake pads were put. However, my car’s light is still on.
In less than two minutes, find out if your auto insurance is being overcharged.
Absolutely! Since your brakes have already been inspected, you should feel comfortable turning the brake light back on. The majority of maintenance lights require manual resetting when the task is finished. You must take the following actions to reset the brake light on your BMW 1 Series:
- Press the odometer reset button on your dash after turning the ignition to the ON position.
- Keep pressing the button. A yellow triangle with an exclamation point inside will be seen on your display. The service menu will then appear.
- To discover the brake light setting, use the turn signal stalk.
- To reset the light, press and hold the BC button on your turn signal stalk.
Examine your insurance alternatives with Jerry to make sure you’re prepared financially in case of an accident. The Jerry app, a registered broker that provides end-to-end support, compiles reasonable rates, assists you in switching plans, and even assists you in terminating your old policy.
What does the BMW’s yellow brake light signify?
I continually receiving a triangle on my dash with an exclamation point and a yellow brake light. It randomly starts up and then shuts off. They topped out the brake fluid after I took it to the dealership to have it checked. but it’s now turning back on. Anyone with knowledge of the issue? thanks.
So, since the dealer filled it off, have you checked the brake fluid level again? You may have a brake system leak if your braking system required enough fluid to trigger the low brake fluid light. How does the pedal feel? When you apply consistent pressure, does it sag at all? When you overnight park, are there any moist areas close to the inside of the wheels?
I didn’t check the amount of the brake fluid. How can I go about doing that? Normally, the pedal feels. Lighting turns on and off. I therefore assume it is the sensor.
There is a sizable black plastic cover on the driver’s side beneath the hood, just where the gas strut—which keeps the hood up—attaches to the body. Both a front and a back clip are present. The brake fluid reservoir can be seen there if you lift it off.
Although I too prefer my eyeballs to any fluid level sensors (crankcase sump?! ), a YELLOW brake indication, according to the table in the non-iDrive handbook, indicates that the brakes are engaged “Drive-off assistant is not working. After the brake is disengaged, the car won’t be kept in position.” A red sign would be low fluid.
What does the BMW’s red brake light mean?
The amber/yellow brake warning lamp and the red brake warning lamp have different functions. When there is a hydraulic issue, such as low brake fluid or a loss of hydraulic pressure in one of the brake circuits, the red (RBWL) lamp will illuminate. If the parking brake is applied or shorted to the ground, it also glows.
If the brake fluid level is low, it lights. Low fluid level is frequently a sign that the brake pads need to be replaced since they are worn out. Brake fluid accumulates in the space behind the caliper’s piston when the brake pads deteriorate. Before adding fluid to the reservoir, it is crucial to inspect the system for leaks.
How can I turn off the dashboard brake light?
RISK: Despite changing the brake pads and associated wear sensors, the dashboard braking system warning light continues to flicker. Steps to take:
- To check that the brake pads and discs are in contact, repeatedly press the brake pedal.
- Turn off the dashboard for a brief period of time.
- Check to check if the light is still on after turning on the dashboard once again. Ask for help and guidance if the brake warning light is still on.
Only for entertainment and informational reasons, the information in this article should not be used as a substitute for consulting a qualified technician or mechanic for expert guidance. We advise you to speak with a licensed technician or mechanic if you have any specific queries or issues regarding any of the subjects discussed here. We will not, under any circumstances, be held responsible for any loss or harm resulting from your reliance on any content.
BMW brake sensor replacement necessary?
The “brake” light on your dashboard or iDrive system is controlled by your BMW brake pad sensor, which also informs you of the remaining life of your brake pads. The sensor is mounted to the brake pad; as soon as the brake pads are completely worn down, the sensor’s tip breaks, tripping the wire and turning on the dashboard light. The brake pad sensor error codes are as follows when using an OBD scanner:
5, 5, 6, 5, 14, 5, 15, and 6F12
Every time you change your brake pads, you should also replace the brake pad sensor. The sensor does not need to be changed every time, but failing to do so could lead to erroneous readings of the amount of life left in your pads and a persistent notification on your dash/iDrive system. The only way to get rid of the light once it appears on the dash is to either swap out the sensor or bypass it, which will stop it from reading the pad life.
My parking brake light won’t turn on; why?
A number of dashboard warning lights may suddenly begin to illuminate. Everyone is aware of the functions of the battery and oil lights, but many other lights call for consulting the owner’s manual. To assist make things a little clearer, we’ll look at several lights and what they represent in the upcoming months.
The parking brake warning light is displayed here. It can be either red or orange, depending on the brand of the car. It flashes to indicate that the parking brake or emergency brake is applied and needs to be disengaged before moving on with a drive.
It indicates that you need to add brake fluid if it stays lit after the parking brake is released or if it flashes intermittently while you’re driving. You must get the braking system checked if you check the fluid, add as necessary, and the light doesn’t go out.
In fact, you should get a brake inspection regardless of whether there is a leak in your brake system. Why? As your brake shoes or pads deteriorate, more fluid is needed to press them against the rotors or drums to stop the car. This dashboard light can be gently alerting you that brake servicing and repairs are about due.
The parking brake needs maintenance if there is an illuminated wrench under the light. The car can be operated safely, but it needs to see a mechanic.
Is your parking brake in need of repair? Go to any of the nine Auto Select auto and truck repair shops in Appleton, Green Bay, Stevens Point, and Weston.
With the brake light on, can I drive?
When you start your car, if the brake warning light illuminates and stays on, do not drive. Turn off your vehicle, then look for potential reasons of the problem.
Do not become alarmed if the brake warning light illuminates while you are driving or in traffic. There are multiple hydraulic braking systems in your car. So, even though it could take a little longer than usual to stop completely, pull over securely and arrange to have your car towed to your house or to a reputable technician for an inspection.
Once more, it’s crucial to avoid continuing to drive while the brake light is on as this could further harm your braking system and be quite dangerous.
*Pro Tip: All of the dashboard lights should come on when you switch on your car. If one or more of them are not turning on, there might be an issue with that particular indicator.
How are brake calipers reset?
One of the chores you must complete while installing new brake pads or before bleeding the braking system is resetting the pistons in your brake caliper.
To demonstrate the difference, a photo of a Shimano Deore M596 brake caliper before and after the pistons were adjusted is provided below.
Your caliper pistons can be repositioned in one of two methods. With the brake pads in place, it is the simplest method. To turn, merely insert a flat-bladed screwdriver between the brake pads. As a result, the brake pads will disengage, pushing the pistons back into their reset position.
Instead of going through the hassle of reinstalling your brake pads if you’ve already taken them out, grab a plastic tire lever and use it to push the pistons back into their housings.
Resetting the position of the pistons should never be done with sharp or metal tools as this could lead to harm.
After readjusting the caliper piston positions, you can now install your new brake pads or bleed block.
On a BMW, how do you reset the red exclamation mark?
Start the engine, then move through the obc until you find the word RESET next to the “flat tyre” sign. To choose, press the stalk’s tip. A tick should display after about 5 seconds of pressing and holding; just drive away, and it will reset itself. Don’t wait for any confirmation because there are no other signs that it has done it.
All owners and aficionados of BMW’s 1 and 2 series have their own forum community. Join the conversation regarding performance, customizations, classifieds, troubleshooting, maintenance, and more!