How To Reset BMW E46 Oil Service?

BMW / By

You shouldn’t have a 20-pin DLC connector after mid-2000. Only the left odometer reset button needs to be held down while the key is turned to position 1. (Accessory). Hold the button down for approximately 5 seconds or until any of the following is visible on the display: OIL SERVICE, Inspection, and Reset. When RESET or RE flashes, release the button and press it once more for additional 5 seconds or so. Press the button once more for a brief period of time as the display flashes. If everything is done correctly, END SIA should appear for a little while. I’m done.

Keep pressing the left odometer reset button.

2) Set the ket to Position #1. The TEST message appeared first.

3) The Oil Service or Inspection with Reset or RE light should have appeared after about 5 seconds.

4) After the Oil Service with Reset light illuminated, I released my grip on the button and pressed it once again while maintaining my grip.

5) As soon as the Oil Service with Reset light began to flash, I released the button and quickly pressed it once more without holding it down (This is where everyone is having problems).

6) After a brief delay, the term Inspection appeared, although earlier it said Oil Service.

7) The final phrase was “END,” and that was all.

BMW 318i e46 Oil Service Indicator Light Reset via impee

Prices: PSN/A (private) or PSN/A (BMW) for professional labor charges to raise a BMW on jack stands, multiplied by 0.5 hours.

Following an oil change, use the following procedure if your OBC has to be reset:

Mid-2000s and Later BMW Models:

You must follow the steps below since you lack the 20-pin DLC connector that older BMW models have.

1) While turning the key to position 1, press and hold the left odometer reset button (Accessory).

For approximately 5 seconds, hold down the button until any of the following appears in the display: RESET OR RESETTER OIL SERVICE OR INSPECTION

2) Press and hold the button for an additional five seconds after releasing it to see RESET or RE flash.

3) Press the button once more very quickly to reset the Service Interval while the display is flashing.

How can I reset the oil service on my BMW?

My uncle, a retired technician, recently changed the oil in my BMW. The maintenance light is still on, so I suppose he forgot to turn it off. How can I turn off the BMW’s oil-change light?

In less than two minutes, find out if your auto insurance is being overcharged.

  • Don’t start the engine after turning the ignition on. You should hit the start button instead of depressing the brake pedal if your car has a push-to-start system.
  • The service menu will show if you continue to depress the trip reset or odometer button on the instrument cluster. The reset button is normally located to the left of the speedometer, and pressing it for around 10 seconds should bring up the service menu.
  • To discover the oil change notice, use the reset button to scroll through the settings. Press the reset button after that.
  • Depending on the model, you might have to scroll through the options using the controls on the turn signal lever until you come across a prompt asking you if you’d like to reset the warning. Then, to reset the turn signal, press the BC button at the lever’s end.
  • When prompted, press and hold the reset or BC button until the display indicates that the device is resetting.

You can save money on automobile expenses by having friends or relatives work on your vehicle, but employing Jerry can help you save money on extra expenses like auto insurance. The typical user of Jerry saves $887 annually on auto insurance.

Don’t be afraid to alter insurance or payment plans because you’re concerned about the extra labor. Jerry takes care of all the paperwork and even assists with canceling your previous insurance! Additionally, you can text one of our agents using the app if you have any questions along the route. They’ll be there for you whenever you need them.

How can my BMW 3 Series be reset?

The mechanic will reset the computer in your BMW after the service is complete so it can record your mileage and let you know when the car will need maintenance again in the future. However, the techniques listed below can help you if you maintain your own car but are unclear of how to reset the computer system.

  • With the engine off, turn the key to the ON position.
  • For TEN seconds, press and HOLD the ODOMETER button. It can be found at the Instrument Cluster’s extreme bottom LEFT corner.
  • The dash screen will display FGSTNR along with a number. Your chassis number is this (See image example).
  • The LAST FOUR numerals are added. Ex: 3+4+5+6= 18 (taken from the image above). Your UNLOCK CODE is going to be 18.
  • Press and hold the ODOMETER button one more until the FGSTNR clearing area appears (you will still see numbers in the top section).
  • Press the odometer button until the upper Menu area (entering code menu) reaches 19 after the bottom area has cleared; When you do, the text will appear at the bottom: Press the odometer button to enter your unlock code after turning the lock on (from the example above) This is seen in the bottom portion.
  • The screen will appear as in the image above after a little period, at which point the menu will once again appear at the top. To access the number 21 menu, press the odometer button (also theentering code menu).
  • On the screen’s bottom, it will say: RESET? To complete the reset, press the odometer button.

Your BMW’s computer has been restarted! The existing settings must now be added again, or new ones must be added.

**NOTE: Slowly repeat the procedures if you are unable to reset the BMW computer on your first attempt. If you’re still having trouble, ask the dealership for help or refer to your car’s owner’s manual.

How can the BMW service reminder be reset?

Till the service notice shows, press and hold the tiny odometer button in the instrument panel’s lower left corner. When the message asks “Reset?” release the button, then press and hold it once again. Press and hold the button while releasing it once more. “Reset in Progress” will be the message displayed.

What kind of oil can a BMW E46 use?

The oil that complies with the BMW LL-01 criteria is the one that should be used in E46 vehicles. These oils are conveniently available on Amazon. This means that oil makers will comply with and generally beyond the qualities that BMW specifies for their engines.

You should always verify your car’s owner’s manual to make sure it needs the BMW LL-01 specification, but I’m almost positive that the non-M E46s do.

You also need to decide on the viscosity of the oil in addition to the type. such as 5w30 or 5w40. In general, you should use 5w40 in warmer climates. 5w30 will be necessary if you reside in a region with exceptionally cold winters. Find out what your neighborhood BMW technician suggests by asking them. Simply because the car rarely experiences temperatures below 30 degrees Fahrenheit, we always run 5w30.

An affiliate site is this one. This website might get a cut of the sale if you decide to use these links. If you decide to click on these links, we sincerely appreciate it. I’m grateful.

How can I turn my BMW inspection light back on?

We decided to revive this tradition and make it a habit because we haven’t featured any BMW tips and tricks in a while. Of course, we can’t accomplish this without your assistance, therefore on this occasion, we kindly invite everyone to write us with any advice, techniques, or fixes for our gorgeous BMWs.

Today, we’re going to demonstrate how to reset the BMW inspection light, which illuminates on your instrument cluster when your car needs service. One of our friends has a 325i, and he frequently gets his oil changed at other places because those places don’t have a BMW reset tool.

Many of you probably already know this, but for those who are still fresh to the BMW world or have just never had to manually reset your light, this information might be useful.

  • Off ignition (POS 0)
  • When the key is in the first position, press and hold the trip odometer button (ACCESSORY)
  • When you notice “Oil Service” or “Inspection” with “Reset” or “Re” in the display, release the button after around 5 seconds.

*Note: If your car has a “High” cluster, you can also view how much fuel you have left until your next service (in liters).

4. When “Reset” or “Re” flashes, press and hold the button once more for approximately five seconds.

5. To reset the Service Interval, briefly press the button one more while the display is blinking. You should see “END SIA” for around two seconds after the new interval has been displayed on the display.

*Take note that you cannot reset if the “Reset” or “Re” does not flash indicating that you have not reached the required minimum consumption level.

If you have attempted this process on any other models except the E46 3 Series, please let us know so we can update this post.

How can my oil sensor be reset?

Clean the oil filler cap if you can. Use the BC button to cycle through the selections on the gauge cluster until the oil level reading appears. After that, hold the BC button down until the clock appears, indicating that the gauge cluster is resetting. only possible when the car is idle and at operational temperature

How frequently should I change my E46’s oil?

Along with the following inspection and service intervals, BMW advises an oil (and filter) service/change every 5,000 miles:

  • Oil and Safety Service (O/S) at 15,000 miles
  • 30 000 miles – BMW I/I/I Inspection
  • Oil and Safety Service (O/S) at 45,000 miles
  • the BMW Inspection II (I/2) at 60,000 miles.
  • Oil and Safety Service (O/S) at 75,000 miles
  • 90,000 kilometers – I/I/I BMW Inspection

A BMW inspection is conducted as part of the oil and safety service to check the condition of your:

  • Brakes
  • Horn
  • fluid and windshield wipers
  • Any lights on your dashboard?
  • The steering mechanism
  • level of engine coolant
  • Every rubber hose and belt
  • components for suspension
  • tire inflation

On my BMW E46, how can I change the time?

Greetings on your new automobile! In order to reset the clock on a BMW E46, do the following:

  • Press the computer button at the left end of the steering wheel stalk to start your car. When you do this, the time should be shown in the instrument cluster.
  • By turning the button on the right instrument cluster, you can adjust the time. The clock is turned backward by turning the button to the left, and forward by turning it to the right.
  • By clicking the button once, you can switch the time from 12 to 24 hours if you’d like.
  • When finished, turn off the engine and take the key out of the ignition. Then, if desired, you can restart your vehicle and look at the time.

Take a little extra time to talk to Jerry about your insurance options while you’re learning more about your new car. The Jerry app instantly compiles rates from more than 50 of the best insurance providers, including Travelers and Nationwide! Once you’ve decided, they even assist you in canceling your old coverage.

On a BMW, how do you reset the red exclamation mark?

Start the engine, then move through the obc until you find the word RESET next to the “flat tyre” sign. To choose, press the stalk’s tip. A tick should display after about 5 seconds of pressing and holding; just drive away, and it will reset itself. Don’t wait for any confirmation because there are no other signs that it has done it.

All owners and aficionados of BMW’s 1 and 2 series have their own forum community. Join the conversation regarding performance, customizations, classifieds, troubleshooting, maintenance, and more!