Can the brake light on a BMW 1 Series be reset? Last week, I had my brakes tested, and new brake pads were put. However, my car’s light is still on.
In less than two minutes, find out if your auto insurance is being overcharged.
Absolutely! Since your brakes have already been inspected, you should feel comfortable turning the brake light back on. The majority of maintenance lights require manual resetting when the task is finished. You must take the following actions to reset the brake light on your BMW 1 Series:
- Press the odometer reset button on your dash after turning the ignition to the ON position.
- Keep pressing the button. A yellow triangle with an exclamation point inside will be seen on your display. The service menu will then appear.
- To discover the brake light setting, use the turn signal stalk.
- To reset the light, press and hold the BC button on your turn signal stalk.
Examine your insurance alternatives with Jerry to make sure you’re prepared financially in case of an accident. The Jerry app, a registered broker that provides end-to-end support, compiles reasonable rates, assists you in switching plans, and even assists you in terminating your old policy.
In This Article...
Is there a way to turn the warning lights back off after replacing the front pads and the sensor? I’ve seen some posts on the 335i, but they don’t appear to apply to the 135i.
I figured it out. I mistakenly believed the cruise control button on the lower stalk to be the odometer reset button. Doh! Basically, turn on the ignition while holding down the odometer reset button until the service option appears after the yellow triangle with the exclamation point on the display. The turn signal selection toggle allows access to the services menu, but it will likely highlight in red the item that needs to be reset first. The display will read reset if you press and hold the BC button on the turn signal for a few seconds.
I recently viewed a YouTube video of a guy demonstrating this material. I’m fairly certain it was in the e90 DIY section. Just tried looking, but I was unsuccessful.
My car has a red front brake indication on (currently at -60miles and counting). If I follow these instructions to try to reset the device, I get to the small spinning clock while holding the BC button, but the device does not reset. With this technique, I can reset/adjust other indicators, but the front pads remain fixed. I essentially get the same outcomes if I attach my BT Scan Tool and perform a condition-based reset (the tool errors trying to reset the front pad indicator, saying something about not being able to talk to the controller).
I don’t have any engine codes, but I did clear the typical fuel pump shadow codes while the tool was connected. No problems there.
My rear brake warning light turned red, but no dealer was required. I recently changed the sensor and restarted the warning. I’ll admit that I had to reset it twice before I realized that the brake warning on the cluster corresponds to the handbrake, but aside than that, everything was OK.
^^ However, this is only accurate if the sensors have actually made contact with the disc. You can reuse your sensors when installing new pads or rotors if you’re proactive and don’t wait for the physical pad sensor alert.
Answer
We’ll need to start by turning on the instruments before we can reset the brake warning light. Then, until the time appears, we must proceed and repeatedly hit the “BC” button. At this point, we must proceed to the instrument panel and press and hold the left button until the reset choices show up. After doing this, we must select the brake reset option and then press and hold the same button again until the reset is complete and the light stops flashing.
On a 2018 BMW x1, how do you reset the brake light?
I was told to return in a month or less to have my brakes replaced the last time I went to the mechanic. I begged them to change them before it was necessary so I wouldn’t have to return so soon. Although the brake light turned on this morning, the brakes are in perfect shape. The mechanic advised me to simply reset the light, but how can I do that on my BMW X1’s brake light?
You made a wise decision by saving a trip and replacing your BMW X1’s brakes earlier than necessary! Fortunately, it only takes a few button presses to reset the brake light, and it won’t take you more than a few minutes.
You must: in order to reset the brake on your BMW X1
- Don’t start the engine after turning the ignition on.
- Up until the service menu appears, keep holding down the trip reset or odometer button. The service menu should show after holding the button down for five to ten seconds. The button is normally located on the left side of the instrument cluster.
- To find the brake warnings, use the reset button or, depending on the model, the controls on the turn signal lever to navigate through the settings.
- When a popup appears asking you if you’d like to reset the warning, press and hold the reset button or BC button on the end of the turn signal lever.
- When prompted, press the reset or BC button once the screen indicates that it is resetting.
Although replacing the brakes on your BMW probably wasn’t inexpensive, you can partially make up for your loss by using Jerry to get auto insurance discounts.
How are the BMW warning lights reset?
Find the tiny odometer button in the instrument panel’s lower left corner. until the service message shows, press and hold. When the message says “Reset,” let go of the button and press and hold it once more.
On a BMW 2020, how do you reset the brake sensor?
My car’s brakes were recently changed by my uncle, but the warning light is still on. Does a BMW X3 have a mechanism to reset the brake light?
Every time the brakes and brake wear sensors are replaced on a BMW X3, the brake light warning must be reset. Fortunately, the brake light reset is simple and should only take a few minutes.
Resetting the brake light on a BMW X3 is made simple by:
- Do not start the engine after turning the ignition to the on position.
- Wait 30 seconds before opening the driver’s side door.
- Wait another 30 seconds after switching the ignition to the off position.
- start the vehicle
If the aforementioned fails, you should:
- Up until the service menu appears, keep holding down the trip reset or odometer button. The service menu should show after holding the button pressed on the left side of the speedometer for approximately ten seconds.
- When prompted to reset the warning, press and hold the reset or BC button on the end of the turn signal lever.
Finding auto insurance shouldn’t be a headache, but dealing with unnecessary warning lights can be.
Jerry is a helpful software that compares quotes from more than 50 leading insurance companies in a couple of seconds. When you locate an insurance you prefer, Jerry can assist with the transition and paperwork. It’s that simple!
My electronic parking brake has to be reset.
Once the ignition is turned off, the Honda Civic’s electric parking brake is intended to activate. This is how to reset it:
- Place the gear lever in PARK and turn the ignition to the ON position. Refrain from applying the brakes.
- The EPB button must be pulled and then released to engage the electric parking brake.
- When you hear a mechanical sound, pull and hold the EPB button for a few seconds before letting go.
- When you hear two mechanical beeps, pull up on the EPB button and keep it there for three seconds before releasing it.
The electric parking brake is fully reset to engage each time the ignition is turned off.
Repeat the process outlined above to disable this function; the system will indicate your success with a simple click.
What does the BMW’s yellow brake light signify?
I continually receiving a triangle on my dash with an exclamation point and a yellow brake light. It randomly starts up and then shuts off. They topped out the brake fluid after I took it to the dealership to have it checked. but it’s now turning back on. Anyone with knowledge of the issue? thanks.
So, since the dealer filled it off, have you checked the brake fluid level again? You may have a brake system leak if your braking system required enough fluid to trigger the low brake fluid light. How does the pedal feel? When you apply consistent pressure, does it sag at all? When you overnight park, are there any moist areas close to the inside of the wheels?
I didn’t check the amount of the brake fluid. How can I go about doing that? Normally, the pedal feels. Lighting turns on and off. I therefore assume it is the sensor.
There is a sizable black plastic cover on the driver’s side beneath the hood, just where the gas strut—which keeps the hood up—attaches to the body. Both a front and a back clip are present. The brake fluid reservoir can be seen there if you lift it off.
Although I too prefer my eyeballs to any fluid level sensors (crankcase sump?! ), a YELLOW brake indication, according to the table in the non-iDrive handbook, indicates that the brakes are engaged “Drive-off assistant is not working. After the brake is disengaged, the car won’t be kept in position.” A red sign would be low fluid.
How can I turn off the dashboard brake light?
RISK: Despite changing the brake pads and associated wear sensors, the dashboard braking system warning light continues to flicker. Steps to take:
- To check that the brake pads and discs are in contact, repeatedly press the brake pedal.
- Turn off the dashboard for a brief period of time.
- Check to check if the light is still on after turning on the dashboard once again. Ask for help and guidance if the brake warning light is still on.
Only for entertainment and informational reasons, the information in this article should not be used as a substitute for consulting a qualified technician or mechanic for expert guidance. We advise you to speak with a licensed technician or mechanic if you have any specific queries or issues regarding any of the subjects discussed here. We will not, under any circumstances, be held responsible for any loss or harm resulting from your reliance on any content.
On a BMW, how do you reset the red exclamation mark?
Start the engine, then move through the obc until you find the word RESET next to the “flat tyre” sign. To choose, press the stalk’s tip. A tick should display after about 5 seconds of pressing and holding; just drive away, and it will reset itself. Don’t wait for any confirmation because there are no other signs that it has done it.
All owners and aficionados of BMW’s 1 and 2 series have their own forum community. Join the conversation regarding performance, customizations, classifieds, troubleshooting, maintenance, and more!
Why does my dashboard’s brake light remain on?
Don’t risk operating the vehicle if you’ve just started it and you see the brake system warning light on.
To begin with, confirm that the parking brake is fully disengaged. Some automobiles have a combined parking brake and braking system warning light. Make sure your parking brake is fully disengaged by checking it and pulling on the release lever. If the dashboard light is still on, your vehicle’s brake system may be malfunctioning and making it difficult for you to stop. Shut off the engine and make plans to have the car delivered to a reliable repair.