- To access the spark plugs at the back of the engine, remove the drain tray that is attached underneath the windshield. A strut brace is mounted over the engine on some versions. It can be taken out for easier access, but it is not required.
- Engine cover removal. Remove any screws holding it in place if there are any. Pull the lid off if no screws can be seen.
- The ignition coil is a connector that a holding clip holds in place. Open the retaining clip slowly. Unplug the wiring harness for the ignition coil.
- Remove the ignition coil. Do not apply undue force if it is stuck. You could break it or cause the silicon insulator to separate. To make it “pop out,” move it around a little bit, twist it back and forth, then pull out simultaneously.
- In older engines, the ignition coils have removable rubber connector boots. If your engine has any of them, pulling will probably cause them to separate from the ignition coil. They will need to be removed individually.
- Check ignition coils for contaminants or cracks if you plan to reuse them. Do not reuse any of these if you find any.
- Look inside the spark plug hole for any oil or debris. Clean it if there is any before removing the spark plug. Be particularly careful because when the spark plug is taken out, any leftover debris can fall into the cylinder.
- Unfasten the spark plug and carefully remove it from the plughole using the proper socket, extension, and ratchet.
- Examine the spark plug directly. It can provide a wealth of information regarding the condition of the engine and that particular cylinder.
- Place the spark plug’s top side into the 3/8 “elastic hose with a 3/8 “Using a rubber hose as a hand tool, hand-tighten the spark plug into the cylinder head plug thread all the way.
- With the aid of a torque wrench, extension, and the proper socket, tighten spark plugs to the required torque.
- Replace the rubber connector boots on engines that have removable connectors for ignition coils. Before installation, dab a little amount of silicone grease on the inner spark plug side of the boot.
- installation of the ignition coil assembly. As soon as you hear a “pop,” push it onto the spark plug.
- Lock the retaining clips after connecting the wiring harness to the ignition coil. Check the connector again for any looseness. Reinstall the engine cover, the scuttle drain, and any additional items in the same order that they were removed.
- Start your BMW engine and watch it in action.
- Utilize the instrument cluster to reset the spark plug reminder.
In This Article...
How much does a BMW spark plug replacement cost?
Best in Automotive Repair Spark plug repair for a BMW 328i typically costs between $219 and $347. The cost of labor is expected to be between $150 and $189, while the cost of parts is between $69 and $158.
How often do I need to replace the spark plugs in my BMW 328i?
Older vehicles with ignition systems that employed distributors, spark plugs, wire, and points are primarily the ones that the word “tune-up” alludes to. Modern coil-on-plug ignition systems with no moving parts and longer service intervals have replaced these antiquated systems.
Most BMWs have been manufactured with platinum-tipped electrode spark plugs since the 1999 model year (and iridium-tipped electrode spark plugs starting in 2006). These spark plugs need to be replaced after 100,000 miles.
(Roughly from 1999 to March 2009; M and turbocharged variants excluded)
Older BMW Motorsport cars like the E36/7 and E85 M Roaster/Coupe, E36 and E46 M3, have two ground strap spark plugs that are comparable to these. The spark plugs in these high-performance engines deteriorate more quickly and need to be replaced after 60,000 miles (Usually during the Inspection Two Services).
In addition, the E60 M5, E63/64 M6, and E90/92 M3 are more recent BMW Motorsport vehicles with lower spark plug service intervals. For optimum performance, these V10 and V8 powered vehicles need to have their spark plugs changed every 37,000 miles.
BMW cars with turbocharged N54 and N63 engines, including the 135i, 335i, and 535i, as well as the X5, X6, have copper-tipped spark plugs that need to be replaced every 37,000 miles (Usually during the third oil service or vehicle check service).
The latest BMW models (2010 and newer 535i, 535i GT, 128i, 328i, X3, X5, etc.) equipped with the new N20 or N55 turbocharged engines, or N52TU engine, require spark plug replacement every fourth engine oil service or 60,000 miles.
How can I tell if the spark plugs in my BMW are bad?
Your automobile may feel a touch “odd,” which is possibly the most evident indicator of damaged spark plugs. It could begin slowly with something as straightforward as poor gas mileage, but it might end up with a lack of acceleration.
How frequently should a BMW have its spark plugs changed?
Spark plugs must be replaced every 60,000 miles in the majority of contemporary BMWs built after 2010 with the N20 or N55 engines. For BMWs with V8, V10, N54, or N63 engines, 37000 miles is the minimum distance before replacement spark plugs are required.
What size spark plug socket is used by BMW?
The N20, N26, N54, and N55 engines all require a 14mm deep thin wall socket for the spark plugs. The majority of folks don’t have this unique type of tool in their toolboxes. This was produced by a BMW OEM source. It’s the proper part for the job, which can greatly contribute to the speed and simplicity of DIY projects. To make the task even simpler, this socket also has an inbuilt magnet.
Call us at 877-639-9648 for complete BMW fitment information or support from one of our BMW experts.
Can I change my own spark plugs?
For a four-cylinder engine, changing spark plugs takes approximately an hour, and you can do it yourself and save at least $100 in labor costs. Most of the time, it’s a straightforward task that will help to maintain optimum performance and the best gas mileage.
How can I tell if I need to replace my spark plugs?
- Starting the automobile is difficult.
- The engine stalls out.
- More frequently, you’re stopping at the gas station.
- The idle of the engine is noisy and harsh.
- Your automobile has trouble picking up speed.
- When driving normally, the engine is rather noisy.
- You have a check engine light on.
How much should replacing spark plugs cost?
My Honda’s engine need new spark plugs. I won’t be able to accomplish this alone; I am not even remotely handy. What is the price of replacing spark plugs?
In less than two minutes, find out if your auto insurance is being overcharged.
We appreciate that you are putting your car’s health first. In general, a mechanic will charge between $115 and $200 to replace a spark plug.
With spark plugs, the price of parts is low.
Depending on the type required, plugs might cost anywhere from $5 to $20 each. You will need between four and eight plugs because you need one plug for each cylinder in your engine.
Labor time makes up the remaining expense. Expect to pay for one to two hours of labor even though this is not a particularly laborious procedure.
Take a few minutes to increase your auto insurance coverage while you’re waiting at the mechanic for your spark plugs to be changed. Download Jerry if you need assistance.
Jerry is a mobile insurance brokerage application created with the goal of reducing your insurance costs. It’s simple to acquire excellent coverage at a reasonable price with the help of the app, which offers you a lengthy range of customised insurance estimates.
When ought the ignition coils in a BMW to be changed?
Your BMW’s ignition coils’ openings are so near to the engine that with time, heat and vibration might harm the coil housing. The typical lifespan of a BMW ignition coil is around 140,000 kilometers. The lifespan of your coils may drastically reduce if you frequently strain your car’s performance. You should prepare to replace your coils every 20,000–25,000 miles if you’re one of the enthusiasts with modified BMWs who enjoys pushing the limits of your vehicle.
Other factors that contribute to ignition coil failure include faulty spark plugs, oil leaks, and engine water corrosion. It’s possible that a damaged spark plug won’t conduct electricity effectively. Due to the excessive heat produced on the insulator side, this can eventually cause the coil housing to melt. Oil leaks will corrode the spark plug and coil connection, decreasing conductivity and ultimately blocking a spark. Finally, water damage will undoubtedly short the circuit formed by the connection between the ignition coil and the spark plug.
Should I swap out my BMW’s ignition coils all at once?
Coil packs are dependable and should endure for the entire life of the car. There is no need to replace everyone if one of them behaves badly. However, you should replace them all if one pack begins to malfunction after the odometer has traveled about 75,000 miles.
How frequently should coil packs be changed? They don’t need to be changed until symptoms start to appear. Most of the time, they don’t need servicing until they’ve traveled 120,000 to 150,000 miles.
Should I replace each spark plug individually?
Should All Spark Plugs Be Replaced At Once? A: In order to achieve uniform performance levels, it is generally preferable to replace all plugs at once.
How frequently should I replace my spark plugs?
Because they are made for long-term durability, spark plugs only need to be changed every 80,000 to 100,000 miles. To save costly engine repairs, they may, however, become damaged earlier than anticipated and need to be replaced.
Is it expensive to maintain a BMW 328i?
Costs of BMW 328i auto maintenance and repairs A BMW 328i is expected to cost between $95 and $3273 in maintenance and repairs, with an average cost of $347.
What noise does a damaged spark plug make?
You may occasionally hear your engine making a distinct banging noise, especially when accelerating. Your spark plugs not correctly detonating and igniting all the fuel is what is making that noise. The unlit gasoline and vapor will eventually catch fire and detonate. You can hear your engine knocking when that happens. Engine knock is frequently caused by faulty spark plugs, but they are easy to replace.
What results in a BMW misfiring?
Faulty wiring is one potential factor in BMW engines misfiring. All of your car’s components eventually wear out and require replacement or repair, and the spark plug wiring is no exception. To effectively ignite the engine of your car, fuel and air are combined. The car is unable to adequately combine the fuel and air, which leads to the engine misfiring, when spark plug wiring is not functioning properly, which is frequently the case. You should get your car regularly inspected by a reputable auto repair in order to preserve the lifespan of your spark plugs and the related wiring.
What goes into a BMW tune-up?
The purpose of Inspection 1 is to optimize your BMW’s general performance and confirm that all of your safety systems are operational. A higher mileage inspection, known as Inspection 2, precedes Inspection 1. Depending on the age of your car, different service intervals are required for Einstein’s checks. Here is a list of everything that is covered in Inspection 1:
- Change the oil and filters
- changing the cabin air filter
- Make that the engine is operating at the proper temperature.
- Check the rear axle and power steering
- Check for transmission leaks
- Checking for leaks visually on fuel connections, lines, and tanks
- Exhaust system thoroughly inspected for leaks, placement, mounting, and general condition
- Check the front control arm and bushing.
- Inspection of the steering system’s overall condition
- examination of the brake pads and discs
- examination of the clutch system connectors and brake lines
- Parking brake cables should be checked for position and movement.
- Check tire pressure, including the spare tire
- examining the tread and wear on the tires
- scanning for fault codes and diagnostic systems
- Antifreeze, coolant, brake fluid, and washer fluid levels should be checked and topped off.
- Examining the hose connections for the heater and engine cooling systems
- Check the AC and test the battery load
- Check the interior and external lighting, as well as the dashboard controls and indicator lighting
- Examine the door and closures, the grease hood, the door, and the trunk latches, as well as the washer and wiper system.
- Checking the operation of the safety belts and looking at the air bag units
- Functionality of the heater, air blowers, defogger, and mirrors is tested.
- Service Indicator reset
- Verify all checkpoints and functionality with a road test.