1. Take off the front bumper’s plastic trim.
5. “the two torx bolts holding the bumper to the vehicle. calls for a torx socket. For simpler access to the bolts, you might need to remove the grille from the bumper and the area around the fog lights.
6. Unplug the horns and the fog lights.
7. Plastic holds the bumper in place at the points where the top of the bumper and the bottom of the fender converge. By pulling the bumper off the automobile, you ought to be able to take it off.
8. The metal bumper and bumper cover will separate into 2 pieces. To remove the bumper cover, unclip and remove the screws from the back side of the bumper.
9. Disassembly is the opposite of installation. SEE THE PHOTOS IN THE DO IT YOURSELF AREA OF THIS FORUM! They are very helpful. Good luck, and remember to take your time and be patient.
In This Article...
Phoenix330ci
1. Take away the bottom-mounted plastic protection.
2. Remove the torque-head bolts that hold the bumper to the frame rails from the two holes in the bottom of the bumper that are located to the front left and right of the center (or bumper brackets).
3. There is one screw that needs to be taken out of the fender well on each side of the automobile.
4. I think the bumper is secured from the bottom by one screw on each side under the automobile.
5. Unplug and disconnect the fog lights. You might need to remove the rings first, but I don’t believe you need to remove the fog lights themselves.
5. Slide the bumper cover off; experts advise using two individuals.
I believe it is essentially the same as the prelude vehicles, however if it is a Mtech II, there is no bumper trim to be removed. Unfortunately, I was never able to locate an excellent video that demonstrates everything. Please correct me if you know better or if I missed something.
Are BMW bumpers repairable?
According to a qualified BMW body shop (not the dealer), it is against BMW’s official policy for bumper repairs on vehicles equipped with lane departure sensors. Due to liability issues, they will only perform a complete replacement.
How much does a BMW bumper repair cost?
A replacement bumper for a passenger car can range in price from $100 to $1,000, according to Cost Helper. The price of installing and painting a new bumper can range from $200 to $600. Pickup truck, SUV, and luxury car bumpers will cost more.
What is the turnaround time for a front bumper replacement?
As was already said, every shop must follow a set of procedures to estimate how long it will take to fix your car.
The insurance company paying the bill will first need to inform the shop of the parts it requires. Additionally, it could occasionally happen that the dealership is out of stock of the specific sort of bumper needed for a particular automobile model. Usually, bumper repairs are completed in no more than three days; however, if the repairs are minor, they may be completed in just one day.
How is an e clip removed?
- To make it easier to grasp, move the E-center clip’s out of the way. The curved side of the E-Clip should be facing you for simple removal. If it needs to be twisted, use your fingers or a pair of needle-nose pliers. With light pressure, the E-clip ought to glide effortlessly.
- Use needle-nose pliers to grasp the E-center. clip’s With the tip of your needle-nose pliers, squeeze the center of your E-clip together. To remove the clip, firmly grip the pliers. The easiest way to remove the E-clips is with needle-nose pliers. But you can also use other kinds of pliers, such locking or slide joint pliers.
- Apply gentle pressure as you pull the E-clip in your direction. Pull your pliers back while holding the E-clip to free it from its place. If you’re having trouble gripping the E-clip, move your pliers’ tip closer to the middle.
How can a rivet be taken out without using a drill?
A third approach is unpolished but effective. (If the appearance of the riveted object is important to you, this method is generally not the best because it can damage the surface.)
- Locate a cold chisel or other tool with a blunt edge (a slot-head screwdriver will do), place the sharp end of the tool against the edge of the rivet head, and then hammer the other end of the tool.
- Continue until the rivet head comes off. The rivet is therefore typically simple to remove. On rare occasions, a punch may be necessary to remove the rivet.
A splash retainer is what?
Product Specifics A push-in device called a splash shield retainer secures the splash shield to a vehicle’s underside. Nylon is used in its construction to prevent corrosion and vibration.