- Hood is open. The hood release on your BMW 3-Series can be found underneath the dashboard. When you hear the BMW hood pop open, pull the lever. The hood safety latch at the front of your 3-Series needs to be released next.
- The hood should be raised and locked open.
- the Coolant Reservoir’s location. The BMW’s coolant reservoir (tank) can then be found. Here, you may check the coolant level and top it out if necessary. The coolant expansion tank is found on the driver’s side of the engine in a 3-Series. Slowly remove the cover. Only after the engine has cooled should you open the cap.
- Remove cap to check the coolant level in a BMW 3-Series. Observe the low and high levels in the coolant reservoir tank. You must replenish coolant if the level falls below the minimal level, or your 3-Series risked overheating. The floating gadget is used by the BMW 3-series to gauge the coolant level.
- Add antifreeze and engine coolant. Use only the BMW-recommended coolant type.
In This Article...
How is antifreeze added to a BMW 328i?
- Locate and clean the coolant reservoir by going to the reservoir.
- Check Level: Check the level of the coolant.
- Add Coolant: Select the right kind of fluid and add it appropriately.
- Replace the cap on the coolant reservoir and tighten it.
Does your BMW require special antifreeze?
In addition to controlling engine temperatures, the quality of your BMW coolant is essential for lubricating the water pump, guarding against corrosion and buildup, providing anti-freeze during the winter, and, in some models, assisting in cooling for engine and gearbox oil coolers. Not just any antifreeze will do; BMWs have special coolant needs (nitrite and phosphate free) to prevent build-up and corrosion of metal components. Along with BMW coolant, we also sell coolant additives like Red Line Water Wetter, which lower combustion chamber temperatures and elevate boiling points in order to prevent detonation and banging.
What kind of antifreeze can you put in a BMW?
No matter what type of car you drive, whether it’s a BMW, Porsche, Mercedes Benz, Audi, Mini, or Volkswagen, your car circulates a solution of water and coolant to dissipate the heat generated within the engine and prevent it from completely melting down.
A Spectrum of Colors
Which coolant type is best for your BMW, Porsche, Mercedes Benz, Audi, or Volkswagen out of the many available options? The answer is the kind that was initially installed in your car. Your coolant may be green, pink, blue, yellow, or even clear depending on the manufacturer. All coolants are naturally transparent, and dye is used to give them color. It has no impact on the coolant’s chemical properties that each producer adds their own colour blend. Because the water in Europe is substantially harder than the water in the United States, European manufacturers prefer coolant that is phosphate-free.
Inorganic Acid Technology (IAT), Organic Acid Technology (OAT), and Hybrid Organic Acid Technology (HOAT) are the three most common coolant types available today. A HOAT coolant is used by your BMW, Porsche, Mercedes Benz, Audi, or Volkswagen.
In order to protect aluminum surfaces, silicate is added to OAT coolants to create HOAT coolants. The cylinder heads and radiators, as well as other parts of your BMW, Mercedes Benz, Porsche, Audi, and Volkswagen engine and cooling systems, are constructed of aluminum.
Silicate and phosphate corrosion inhibitors are not used in OAT coolants. These coolants are made to last for 150,000 miles and have a long service life. It should be mentioned, nevertheless, that German Auto Center and the majority of manufacturers advise cleansing or replacing the coolant every two years.
The metal (Iron) components of the engine and cooling system are protected by traditional coolants, which are IAT coolants and use silicate and phosphate corrosion inhibitors. IAT coolants shouldn’t be utilized because the majority of the iron components in your BMW, Mercedes Benz, Porsche, Mini, Audi, and Volkswagen have been replaced with aluminum and other lighter composites.
It’s crucial to keep in mind that modern German performance cars, whether you drive a Porsche, Mercedes Benz, Mini BMW, Volkswagen, or Audi, will last you for many miles and years if you maintain them properly. German Auto Center in Austin is the place to go for German auto repairs. We will be pleased to help you!
Is a BMW compatible with Prestone antifreeze?
P/N: AF6100. The best formula for every BMW (r), every Mini (r), every Volvo (r), every Mercedes (r) older than 2014, every Volkswagen (r), every Audi (r), every Jaguar (r), and every Porsche (r) older than 1996. This technology controls the temperature of your engine, prevents it from freezing, and shields it from corrosion.
What shade is the antifreeze in BMWs?
To maintain your cooling system operating at its peak, we advise using only German OEM BMW engine antifreeze, part number 83192468442. Because they don’t include nitrites, amines, phosphates, or borates, BMW exclusively suggests specific coolants. It is not permitted to use store-bought coolant from a nearby parts retailer.
2018 saw the introduction of this new green coolant, which has replaced the previous blue coolant. Green can be used on automobiles before 2018 and is backwards compatible with blue. BMW advises against using the older blue formula on vehicles created after January 2018.
The silicates in the green coolant provide further protection for the cooling system’s internals, although the coolant needs to be changed every two years.
For increased corrosion resistance, anti-freeze defense, and water pump lubrication in street cars, we advise combining distilled water in a 1:1 ratio with the mixture. Reduce the amount of antifreeze in your coolant mixture if you want more cooling properties, but only in warmer climates where freezing is impossible. We advise monitoring the freezing point of the coolant mixture if you want to use antifreeze and water ratios other than 1:1.
Red Line Water Wetter can also be added if high temperatures could lead to engine banging or pre-ignition.
- Original BMW HT12 antifreeze from Germany, part number 83192468442
- optimum cooling, freeze prevention, lubrication of the water pump, and corrosion resistance
My BMW has no coolant, can I add some?
You can purchase antifreeze that is full strength and needs to be diluted with distilled water before being applied to the engine system, or you can purchase ready-made combinations of coolant that already have water added.
In a BMW, where is the coolant located?
Find the coolant reservoir by opening the hood. This tiny black tank is typically located to the left of the engine in BMW models, but it isn’t always the case. If you’re unsure of what to look for, double-check your owner’s manual. Turn the cap slowly counterclockwise to gradually remove the extra pressure.
BMW coolant is it pre-mixed?
BMW coolant is not pre-mixed when purchased. Simply purchase a gallon of coolant and a gallon of distilled water, then prepare the mixture as necessary. I would just add a cup of distilled water if it only needs, say, a cup of coolant or water. At the dealer, they appear to only do that.
How long must you wait before adding antifreeze to your car?
Put on gloves, open the hood, and locate the radiator cap after waiting at least 15 minutes and the hood is cool to the touch, advises Reina. If necessary, refer to the owner’s manual. To relieve pressure that has built up due to the coolant expanding when heated, cover the cap with a towel and carefully push down and loosen it a quarter turn. When the liquid reaches the “full” level, fully open the radiator cap and slowly add coolant (half water, half antifreeze). The little, transparent plastic overflow reservoir located on the side of the radiator should also be filled with coolant, he advises. After that, put the cap back on and start the engine. You can proceed with caution while keeping an eye on the temperature gauge or light if the red warning light goes out or the temperature gauge returns to normal, advises Reina.
What is the price of BMW coolant?
A BMW 328i coolant change typically costs between $276 and $315. While materials are priced at $124, labor costs are projected to range from $151 to $191.
Do I fill my coolant reservoir with antifreeze?
Antifreeze is simply poured into the expansion tank, or reservoir, where engine coolant is kept, after being combined with water. After that, it will filter around the engine and combine with your coolant to prevent the liquid from freezing. Engine coolant, antifreeze, and K-Seal will all combine without a hitch if you have already applied K-Seal, K-Seal HD, or K-Seal Ultimate to your automobile, preventing leaks and potential engine damage.
Why is blue coolant used by BMW?
The majority of coolant manufacturers in East Texas, where we can experience a wide variety of temperature variations throughout the year, offer an engine coolant that is a 50/50 combination.
In order to receive the greatest cooling benefits for our Texas climate, BMW “Blue Coolant” must be mixed and added to your cooling system in the right manner. This calls for a coolant flush and refill procedure that removes air and old coolant from your system to improve engine safety.
Because it is silicate and phosphate free and has a far longer lifespan inside of your car’s cooling system, we advise using BMW “Blue” coolant in your vehicle.
Come in right away to pick up a gallon of fuel, or let us repair the cooling system in your car in time for the Texas heat.
Why does my BMW’s coolant gauge show low when it is full?
If the low coolant indicator on your dashboard illuminates, your car may be having one of the following problems:
- The most frequent reason for the coolant light on your car to come on is that the coolant is low. While it’s possible that the car is just short on coolant, it’s more likely that it has another problem that’s causing it to gradually lose coolant over time. You should have your car checked out and serviced if this is the case.
- Faulty Sensor: Your vehicle needs a sensor that measures the amount of coolant in its engine in order to know when the coolant level is low. When the coolant level drops too low, a floating sensor in the coolant reservoir of the majority of automobiles activates, putting on the warning light.
Your vehicle’s coolant sensor may be broken if you check your coolant reservoir and it looks to be full but your low coolant signal is on. The majority of auto repair businesses are able to identify and replace faulty sensors.
Are coolant and antifreeze interchangeable terms?
Antifreeze, commonly referred to as engine coolant, is combined with water to prevent the radiator from freezing in extremely cold weather and overheating in extremely hot weather. Knowing which coolant type is best for your automobile or truck is crucial because there are numerous varieties available.
Do I have to wait to drive after adding coolant?
After adding coolant, how long should I let the engine run? The most crucial thing, he continues, is “your own safety.” The engine, hood, and any leaking coolant can all cool down by waiting for at least 15 minutes.
What does the BMW’s yellow engine light signify?
Your BMW should be taken in right away if the check engine light begins to flash. This indicates that there is an urgent need for repair. Usually, a serious engine misfire that causes unburned fuel to leak into the exhaust system is indicated by this blinking light.
How long can you keep your coolant low?
How long can an engine run without coolant? is a question we hear a lot. Maybe answering this issue will be simpler now that you are aware of how crucial radiator coolant is. It is dangerous to drive a car with low or no engine coolant since it could harm some of the engine’s secondary and even primary components. It is preferable to stop if there is insufficient coolant in the vehicle. Even a brief drive in such a vehicle is not recommended because it could seriously harm the engine of your vehicle and incur expensive repairs.
Many new and modern automobile brands have a cut-off feature that checks the engine temperature and detects a lack of coolant. This detection feature turns off the car engine to guard against potential engine damage if there is a shortage of coolant in the cooling system of the car and, as a result, a perception of a significant increase in engine temperature.
However, if you drive an older vehicle, you must be aware of the symptoms of a coolant shortage to save your engines from overheating, seizing, or bursting a gasket. The following is a list of some of the most frequent cooling system parts that sustain the most harm when the cooling system overheats and runs out of coolant:
- water meter
- head seals
- engine timing for the cylinders and pistons
- piston head
- twisted or warped connection rods
- Lack of a crank
Repairing or replacing these parts is quite pricey. Therefore, try to avoid allowing your car’s cooling system to overheat due to a shortage of coolant.
How far can a car be driven without coolant, then? You can continue driving for a while if your car’s coolant level is low. Really, it depends on the coolant level. You can drive your car for a few days if it is low but still higher than the required amount. However, if the level is below the minimum, kindly do not even attempt to start your engine.