Take the BMW key fob you want to configure, hold down the unlock button, and then press and hold the BMW logo three times. The doors should lock and unlock once more. When this occurs, you are ready to go! Your BMW key fob has been programmed by you.
In This Article...
How to Use Your BMW Key Fob Remote
Although pre-programmed for your car, your key still needs to be activated in order to be used.
Hold your new key fob flat on the dim battery indicator next to the steering column to accomplish this. After then, keep pressing the start/stop button until the “no key” warning light goes out. To check that activation was successful, press the start/stop button once more.
If this doesn’t work, you might need to activate your new key while removing your old key fob from the signal range to avoid interference. To accomplish this, first unlock your BMW with the existing key before having someone carry the key a short distance away from your car. After that, you can push the start/stop button while holding your new key against the steering column.
How can I set up my BMW keyfob to work with my car?
Steps for Programming a New BMW Key Fob After then, remove your key from the ignition. While keeping the unlock button depressed, press the BMW logo three times on your BMW key fob. After pressing the BMW logo three times, release the unlock button. Once the ignition is turned on, your new key should be associated with your BMW.
How is a 2008 BMW key fob programmed?
How to Set Up a New BMW Key Fob Press the BMW logo three times while holding down the unlock button, and then let go. Within 30 seconds after the initial key programming, repeat step three if you still have more keys you’d like to program. To finish the procedure, start the engine.
How is a 2014 BMW key fob programmed?
Press the lock button (the BMW logo) three times while simultaneously holding down the unlock button, and then let go of the unlock button. Repeat step three with the extra key(s) within 30 seconds of programming the first key if you want to program more than one BMW key fob at the same time.
How can my BMW key fob be reset?
BMW key fob should be taken out of the ignition. Press the lock button (the BMW logo) three times while still holding down the unlock button, and then let go. If you need to program more than one key fob, go back to step 3 within 30 seconds following the first key programming. Activate the ignition.
Do BMW keys require programming?
Key fobs that have been activated as detailed above can only open your car manually and cannot be used with the Comfort Access feature in E Series BMWs and MINIs.
It is important to code your car to erase the old key profile and set the new key for Comfort Access use in order to activate your new key fob for use with Comfort Access. This can be done at your neighborhood BMW/MINI dealership or we can remotely code it for you.
Our touchscreen key fobs for BMWs from the G Series don’t need to be programmed to function with your particular BMW.
Without the original, how can a key fob be programmed?
After locking every door, turn the ignition off. Set the accessory or “ACC” position on the ignition key. The door locks will cycle once once you turn the ignition key off once more. To program the key fob, press any button three times straight.
How can I program my BMW key fob now that the battery has been changed?
Remove the ignition key from the car. Press the BMW logo three times while holding down the unlock button, and then let go of the button. Repeat step 3 within 30 seconds after the initial key programming if you want to program any more keys. To finish the procedure, start the engine.
Can a key fob be programmed without visiting the dealership?
According to John Ibbotson, CR’s head technician, “If you have a car that was constructed within the previous five years, a new-car dealer will typically be your best chance when you need a replacement key fob.” This is because expensive programming equipment is needed.
We discovered from Audi and Subaru dealers that some key fobs won’t function with aftermarket key fobs, despite the temptation to go for a less expensive one online.
A service advisor at Hoffman Audi in East Hartford, Connecticut remarked, “If you want a new key fob for your Audi, it has to come from us.” The key fob has a built-in security chip that cannot be modified to work with another Audi. A new aftermarket Audi key fob cannot be purchased online because of the requirement for this chip. He claimed that “the fob has evolved into a crucial component of the security of the car.” We were informed that the typical cost of replacing an Audi key fob, including programming, is $500.
This applies to all European vehicles, not just Audi. Because the manufacturer can only program the digital key encryption in a small number of exclusive stores in North America, they nearly always require the customer to see a dealer, said Yu of CR.
Other merchants we contacted, such a Lexus dealership and a Chrysler/Jeep/Dodge dealership, stated they don’t mind attempting to program aftermarket fobs if the buyer requests it as long as the customer is aware of the dangers.
We were advised by a service advisor at a Lexus dealer that they were reluctant to work with aftermarket key fobs. If we try to program it and it doesn’t function, we still have to bill them for our efforts, we can’t warranty parts or labor.
Fortunately, even if you have to visit a dealer, the procedure is quick. Key-fob programming, according to the majority of the dealers we spoke with, usually only requires 15 to 30 minutes, and the entire process, including creating the mechanical replacement key, rarely lasts longer than an hour.
Even if they handle everything for you, going to the dealer doesn’t have to be expensive. Even with European brands, this held true. A replacement fob with a laser-cut key and programming for CR’s 2015 VW Jetta would cost roughly $225, according to a local Volkswagen dealer with whom we spoke.
Customers can save money on programming with some companies, like Chevrolet. For instance, a Chevrolet official informed us that the key-fob programming does not need to be done at the dealership and that General Motors key fobs are on the more affordable side ($147.98 for a 2019 Chevrolet Malibu with keyless entry, push-button start, and remote start).
The car must be present, he added. “The programming technique is explained in the vehicle owner’s manual.
Be advised that most customer-programmable key fobs, regardless of brand, require two active, functional keys in order to program a third new key without visiting the dealer, according to Yu.
How is a key fob programmed at a dealership?
You will need to contact an automobile locksmith (or dealer) to help you if you are unable to self-program your keys (either because there isn’t a process for doing so, you don’t have the necessary number of functioning keys, the tools/computer/software needed is too expensive, or all of the above).
In order for auto tool makers to create software and hardware that enables them to program their vehicle keys, the majority of US and Asian auto manufacturers share their programming protocols with them.
In order to provide programming as a service to their clients, the locksmith then obtains this equipment.
An automobile locksmith will insert a computer with the necessary software into your OBD port below in order to program a car key, remote, or FOB (commonly found below your dashboard).
Many different businesses provide computers and software for programming. They frequently offer support for many car makes and models.
No system can program all the makes and models, thus a locksmith who wishes to repair car keys may have to make a significant investment in these equipment.
The locksmith will be able to add and remove keys from the car using the programming software. Because of the following, this is helpful:
- Some vehicles, like Fords, only let a certain number of keys into the vehicle’s computer system. Ford vehicles can only have a maximum of four keys. In order to make room for your new key to be programmed, a locksmith might utilize a computer to delete keys that are no longer in use.
- It is possible to remove keys from the vehicle after they have been lost or stolen so that they can no longer be used to unlock the doors or start the vehicle (for FOBs/Smart Keys).
However, a locksmith cannot program keys on these computers nonstop. Most often, a “token” system is in place that restricts the computers’ ability to program the car to times when a pre-paid token is available for use.
Tokens are required for programming, and one token is required for each try, according to your neighborhood locksmith. As a result, the locksmith has to pay for each attempt at programming a car key. The programming cost the locksmith charges already includes this.
Depending on who is providing the code, the vehicle, and the locksmith employed, the cost to program a car key can range from $25 to $100. The price will be higher if a second code (a skim code) is required.
Adding a skim code is necessary when attempting to program some automobiles. This code is available from the vendor, but at a price. This fee, which is typically $60, is transferred to you.
By giving the dealer your title in person, you might be able to obtain this skim code on your own. They typically don’t charge the owner of the vehicle because they believe this to be information that belongs to you. Normally, you have to collect this information in person, but it could help you save some money on the price of getting a backup key.
Note: German automakers do not divulge their procedures (see article). Therefore, you will almost probably need to go to a dealer and, sure, it will cost much more if you own a Mercedes, BMW, VW, Porsche, etc.
Ask the vendor if you can purchase the key or fob elsewhere if you have one of the aforementioned items. Some of these vendors will only program keys they sell directly to customers and won’t program keys that were outsourced. However, if they DO program/cut them, you might be able to save some money on the key’s price.
Do you need to reprogramme your BMW key fob after a battery change?
A remote key fob needs to be associated with your vehicle particularly in order to be secure.
This stops people who drive the same make and model of automobile as you from using their remote to access your car. You’ll need to reconfigure the fob if changing the batteries has reset this connection or if it was somehow disrupted in order to get it to detect your car once more.
The cost of a BMW key fob
The price of a 2020 Toyota Sienna fob was comparable. Dealers, however, gave prices as low as $150 to replace a key fob for a 2017 Honda Accord. A number of BMW retailers claimed that the additional security features built into the 2020 X5 key fob justifies the roughly $500 they spend to replace and program one.
A key fob can a locksmith program it?
Car fobs have a peculiar propensity for getting lost—and not just misplaced—in the wrong pocket.
Unfortunately, the fob needs to be replaced when this occurs in order for us to keep using the car.
You might be able to start your automobile and drive it if you have a spare key.
However, there are times when driving your car requires merely the key fob. Therefore, getting a replacement key fob is crucial.
Your initial thought is usually to replace the fob and keys at a car dealership. Additionally, while a dealership may be helpful for replacements, they can be costly and time-consuming.
Fortunately, there is a quicker, more affordable alternative—you may call a locksmith.
A skilled locksmith possesses all the knowledge of a car dealership and is aware of the value of your protection.