BMW key fob should be taken out of the ignition. Press the lock button (the BMW logo) three times while still holding down the unlock button, and then let go. If you need to program more than one key fob, go back to step 3 within 30 seconds following the first key programming. Start the engine.
In This Article...
How to Use Your BMW Key Fob Remote
Although pre-programmed for your car, your key still needs to be activated in order to be used.
Hold your new key fob flat on the dim battery indicator next to the steering column to accomplish this. After then, keep pressing the start/stop button until the “no key” warning light goes out. To check that activation was successful, press the start/stop button once more.
If this doesn’t work, you might need to activate your new key while removing your old key fob from the signal range to avoid interference. To accomplish this, first unlock your BMW with the existing key before having someone carry the key a short distance away from your car. After that, you can push the start/stop button while holding your new key against the steering column.
Key fob remote programming instructions for the BMW 3 Series
3. After removing the ignition key, press and hold the unlock button for 15 seconds. Then, within a 5-second interval, press the key lock button three times.
4. Let go of the buttons.
5. Doors will lock and unlock to demonstrate that proper programming has taken place.
Approach 2:
One key that is already programmed and one key that needs to be programmed are required for this procedure.
1) Enter and lock every door.
2) Start the ignition and swiftly turn it off. Start the process now (no more than 5 seconds). 30 seconds must pass before the next action is taken.
3. Take out the first key.
4) To put the key closer to the antenna on the remote receiver, hold it up towards your left shoulder.
5) Press the lock button three times while keeping the unlock button depressed. As soon as the unlock button is released, the doors lock to authenticate the procedure.
6) Quickly carry out steps 4 and 5 for key #2 and so forth.
If that doesn’t work, try pressing the keys in reverse. vs. 1 then 2, key 2 then key 1
Approach 3:
1. Quickly turn the key to position 1 five times. 2. Take out the key. 3. Hold the unlock button while pressing the lock button three times.
4. Within 30 seconds, press the same button if you have another key. 5. To complete, turn on the ignition.
PLEASE NOTE: This programming process modifies the key’s remote control component. Any transponder chip used by the immobilizer (which prevents the automobile from starting) cannot be programmed; this must be done by a professional.
PLEASE NOTE: This programming process modifies the key’s remote control component. Any transponder chip used by the immobilizer (which prevents the automobile from starting) cannot be programmed; this must be done by a professional. You must use diagnostic tools to have your remote configured to your vehicle at your neighborhood dealer or locksmith.
Want a professional to configure the remote for you since you’re having problems doing it yourself? Find a qualified key fob installer in your neighborhood by typing your city or zip code in the search box below.
Was this Knowledgeable? Please consider making a gift of any kind to support this blog! Your contributions aid in the upkeep of this website. We appreciate your visit and donation.
How can I program my key fob for my 2010 BMW?
BMW Smart Keys:
Start the vehicle by placing the new key fob against the designated location on the right side of the steering column. It only required that to make the new fob functional. In reality, the Nav screen appeared right away and asked for a name for the profile connected to the new key fob.
One crucial detail is that this will only function with a “NEW” smart remote or key. In order for the instructions in this thread to function with a used smart key, it must first be “FLASHED” or reset.
Approach 1:
1. Operating inside the car with the doors closed
2. Within five seconds, switch the ignition from position 1 to off.
If that doesn’t work, try pressing the keys in reverse. 1 then 2, as opposed to 2 then 1.
4. Within 30 seconds, press the same button if you have another key. 5. Start the engine to complete.
PLEASE NOTE: This programming process modifies the key’s remote control component. Any transponder chip for the immobilizer (vehicle starting) cannot be programmed; a professional must do it. You must use diagnostic tools to have your remote configured to your vehicle at your neighborhood dealer or locksmith.
How do I set up the key for my 2010 BMW 328i?
How to Set Up a New BMW Key Fob Take out the key. Press the BMW logo three times while holding down the unlock button, and then let go. Within 30 seconds after the initial key programming, repeat step three if you still have more keys you’d like to program. To finish the procedure, start the engine.
How can I set up my BMW keyfob to work with my car?
Steps for Programming a New BMW Key Fob After then, remove your key from the ignition. While keeping the unlock button depressed, press the BMW logo three times on your BMW key fob. After pressing the BMW logo three times, release the unlock button. Once the ignition is turned on, your new key should be associated with your BMW.
How is a 2006 BMW key fob programmed?
Hold the unlock button down while pressing the Round (lock button) three times with the working key, then let go of the unlock button. Ideally, doors lock and unlock. Hold the unlock button down while using the new key to press the Round (lock button) three times before releasing the unlock button. Once the doors lock and unlock, you’re done.
How can my BMW key fob be reset?
BMW key fob should be taken out of the ignition. Press the lock button (the BMW logo) three times while still holding down the unlock button, and then let go. If you need to program more than one key fob, go back to step 3 within 30 seconds following the first key programming. Activate the ignition.
Can you program your own BMW key?
Take the BMW key fob you want to configure, hold down the unlock button, and then press and hold the BMW logo three times. The doors should lock and unlock once more. When this occurs, you are ready to go! You’ve set up your BMW key fob.
How can I program my BMW key fob now that the battery has been changed?
Remove the ignition key from the car. Press the BMW logo three times while holding down the unlock button, and then let go of the button. Repeat step 3 within 30 seconds after the initial key programming if you want to program any more keys. To finish the procedure, start the engine.
BMW may operate without a key fob.
You won’t be able to use keyless entry or remote unlocking if your BMW has Comfort Access if the battery in your key fob has died. You can still enter and manually start your automobile, though.
Press and hold the key release button at the remote fob’s base while unlocking the door of your car, then slide out the internal key blade. This can be used in place of a standard key to unlock your car. You can locate a little hole on the bottom of the handle if the keyhole is hidden on your car door. Use the key blade to pry off the trim panel and expose the keyhole by inserting it into the hole.
Once you’re inside, put your remote key fob in the ignition slot or, if your car doesn’t have one, press it up against the steering column’s key markings. If your key fob dies, you will still be able to start your BMW using the start/stop button on the dashboard.
Can a key fob be programmed without visiting the dealership?
Can a key fob be programmed without visiting the dealership? Yes, you can program the key fob’s locking and unlocking features without visiting the dealership. However, you might need to visit the dealership or a locksmith if you need to program the transponder in order to be able to start the car with the key.
Why won’t my key fob function?
As you may think, the battery is the main cause of failure for an electric key fob. Although you might need a ride to get to the store to get a replacement fob battery, this is a reasonably simple problem to fix.
The cost of a BMW key fob
The price of a 2020 Toyota Sienna fob was comparable. Dealers, however, gave prices as low as $150 to replace a key fob for a 2017 Honda Accord. A number of BMW retailers claimed that the additional security features built into the 2020 X5 key fob justifies the roughly $500 they spend to replace and program one.
How can I obtain an additional BMW key?
A recent news story claimed that 30% of car owners lose their keys every week. Even while it may occasionally be a little inconvenience, vehicle owners can avoid having their day ruined by it with a little advance forethought. Obtaining a backup key is the most effective approach to make this happen.
Every year, cars get more technologically advanced, and what was once just a basic metal key keeps evolving into a smart fob with a variety of features. You have three choices for getting a new or replacement key for your BMW:
- You can cooperate with your neighborhood BMW dealer.
- You can work with a neighborhood locksmith business that has the skills necessary to duplicate and program BMW keys and fobs.
- You can obtain a “blank” replacement key and fob online, then take it to your neighborhood dealer or locksmith to have it programmed and cut once it arrives.
You will need to have your own personal identifying information, such as the BMW’s VIN and the year and model, in order to use any of these choices. In addition, you’ll need to have identification from the government and documentation showing your identity as the car’s owner. It may seem obvious, but having the necessary information on hand will speed up the process of procuring a replacement key if you find yourself in need of one after locking yourself out. The situation might become less stressful as a result of this.
The dealership may require you to tow your car there so they may make your replacement key if you opt to use them in an emergency and need the replacement key right away. They can come to you if you choose a trained local locksmith, which will save you time, money, and stress.
Why doesn’t my automobile recognize my key fob?
Key fob battery failure The most frequent cause of a keyless entry system failing to send signals is a faulty battery in the key fob. Use the extra key fob to unlock the car and turn on the ignition if one is available. Use the key that is included in the spare fob if it is not available to unlock the door.