As you mentioned, BMW main dealers make the license plates; each time they have done so for me, they have added their logo. A tab with the BMW logo has been put to the bottom of my local dealer’s license plates. Their name appears on the plates themselves in little print.
In This Article...
How are the front license plate rivets removed?
It should be noted that the method presented here will work with many various car makes and models. This should apply if your license plate bracket is fastened on with plastic rivets. Chevy Equinox, Cruze, Ford Explorer, Fusion, Chevy Silverado, Subaru, etc. are few examples.
It shouldn’t take more than ten minutes to complete something this simple. Personally, I believe the front license plate makes the car look cleaner, and fortunately, local regulations in my area only call for one rear license plate.
As you can see from the photographs below, it’s quite simple. In order to get access the four plastic rivets holding the holder to the bumper cover, you basically need to remove the plate itself. Simply slowly drill the middle of the rivets using a bigger drillbit. You might need to use some needlenose pliers or another tool to sort of hold the outer edge of the rivet from spinning with the bit if the rivets turn as you’re drilling. Use caution; although it could be enticing to use your fingers, resist the urge.
First, a “before” photo
In order to remove the four plastic rivets, carefully drill them out with a larger drill bit (at least 1/4″), the larger the better up to 3/8″.
Just be careful not to drill through the bumper; you’re simply wanting to remove the rivet.
You should notice this after carefully drilling; take note that the drill bit did not even make contact with the bumper. At this point, the plastic front portion of the rivet separates from the rivet:
The bumper won’t be damaged by using a large drill bit, as you can see from the last image, even if you go a little too deep. However, the plastic plate holder will begin to suffer damage. Therefore, a larger drill bit is preferable. Do the same for each of the four plastic rivets.
My next action was to insert the back side of each rivet into the bumper cover and shake the cover until the rivets’ rear ends fell to the ground. This step is optional; to remove the last piece of plastic, I just used a little awl, but you might equally well use a small screwdriver. Just be careful not to scratch the bumper paint.
Here are the backs of those rivets. Oh well, I only succeeded in convincing 3 of the 4 to resign.
Clean ‘er up; as you can see, the holder has left a very slight mark underneath. I can definitely buff it out, but from another viewpoint, it looks okay.
Well, good luck with your T-Bird or Cougar. Sadly, there are still 4 holes in the bumper cover, but that is the how things are. I intend to fill the holes with little plastic plugs that I will purchase, paint body color, and insert.
What if, in Texas, my car lacks a front license plate holder?
How many license plates must your car have to abide with Texas law? Is there a one-plate requirement or a two-plate limit? Should you make holes in your car’s front bumper to attach a front license plate, or will a rear plate suffice? You may have done a thorough Google search on license plate laws if you are reading this essay out of frustration. Learn what the Texas Transportation Code says about license plates and how it affects you as a driver in Texas.
In Texas, do I require a front license plate? Yes. According to Texas law, every car must have license plates on the front and back of it. Texas currently levies a $200.00 punishment for failing to display a front license plate.
How are license plates attached without screws?
- Use of VELCRO(r) Brand Heavy Duty Tape is by far the simplest method for attaching a new license plate to your vehicle.
- To begin, make sure that both the rear of the license plate and your car are clean, dry, and ready to receive the VELCRO(r) Brand Heavy Duty Tape.
How do you attach 4D license plates?
adhesive fastening To firmly stick and retain the plate against the car, they employ double-sided pads, but it takes more than simply pasting them on without any preparation. Make sure the car’s contact surface is free of any mud and filth you may have acquired during your travels.
Can you attach a license plate to Velcro?
To answer your concern, the Velcro WILL hold up quite fine. However, if you ever want to detach the component from the paintwork again, there may be a problem. The clearbra, though, would fall off in its place, so it wouldn’t be an issue if you had one.
In California, is a front license plate required?
You might be asking, “Do I need a front license plate in California,” as you prepare to drive your new vehicle on the streets of Los Angeles. Yes, it is the answer. Although some motorists prefer the streamlined appearance of a vehicle without a license plate, driving legally in California requires both a front and rear license plate.
Does New Jersey require a front plate?
In fact, New Jersey is a two-plate state, meaning that you must have a license plate on the front and back of your car. If you don’t, you run the danger of being stopped and being charged heavily. It is impossible to drive without a front license plate in New Jersey, so go ahead and take care of it by attaching your front license plate correctly before you go. Why risk getting into trouble when you can avoid it, after all?
The CoPilot app isn’t just for purchasing a car; it can also be used to keep track of recalls and receive recommendations on which regular maintenance activities are most crucial.
In New York, is a front license plate required?
Vehicles must have two license plates, one on the front and one on the back, according to NY and NJ regulations. All classes of street vehicles must have one in the back, with the exception of motorcyclists. 2
What kind of drill bit do you employ for license plates?
Screwing a Number Plate Into Place Using screws is one of the most typical techniques to fasten a license plate to an automobile. You will require the following tools for this process: – A drill equipped with a 6mm or 4mm drill bit.
Is it better to screw or stick license plates?
When plates need to be changed, they are difficult to remove. By using our self-adhesive pads, attaching your license plates to your car is most likely the simplest process. However, you should use the self-tapping screws with matching plastic head covers if you want a little bit extra security against number plate theft.
Why is Florida devoid of front plates?
a car’s aesthetics But the idea of a front license plate might not be appealing to people who drive sports cars, classic autos, or expensive vehicles. This is so because certain automobiles aren’t built with front plates. Therefore, putting front plates to the vehicle may seem like vandalism.