You may install the BMW E46 LED Halo Rings by opening the BMW E46 3 Series headlight lamps using the installation guide provided. These items can be found in the category BMW LED Halo Rings for Angel Eyes.
1) Pop the hood. First, remove the side marking using a Philips head screwdriver.
2) Advance and pull the lamp assembly away from the car.
3) Pull the trim away from the headlight by raising the five (5) tabs shown to by the arrows.
4) The sides of the headlight have three (3) additional tabs. Also release them. The bottom section should be removed away from the headlamp.
5) As shown by the yellow arrows, unfasten the additional seven (7) bolts holding the lens assembly to the headlight. Take the lens off.
6) Unhook the seven (7) clips holding the headlamp bezel to the bezel. Take the bezel off.
7) To mount the rings, use the included clips and double-sided tape.
8) Disassemble the intake duct assembly by removing the four (4) plastic clips holding it in place.
9) Remove the rubber insulator and the high beam H7 bulb.
10) Push down the exposed metal on the connector’s top and pull the prong out from the back to unpin the plastic connector from the angel eye rings.
11) Pass the wires coming from the rings through the H7 bulb’s aperture in the headlamp and the headlight itself. To make place for the cables, a tiny incision may be necessary. Utilizing pliers, pull the wires through.
Repin the connectors (12). Push up the metal that was depressed from step 10 before inserting the prongs. To secure the prongs inside the connector, pull them through.
13) The vehicle’s positive and grounding connections are located in an exposed space on the top of the engine compartment. The majority of the wiring will be mounted here along with the relay. The yellow/grey wire can be inserted through this into the cabin to your foot area light positive wire and have it tapped there. The rubber grommet provides access to the interior of the cabin.
14) Attach the ground wire to one of the two grounding points indicated in the preceding image and mount the relay someplace inside this compartment.
15) Join the red wire that is positive to the positive terminal.
16) Follow the diagram below to route the wiring for the passenger-side angel eyes along the chassis.
17) As shown in the illustration, run the wire for the driver-side angel eye over the top and to the other side. The upper driver-side engine compartment is where you want to point the blue trigger wire.
18) To remove the cover of the driver-side compartment, remove the four (4) T25 Torx screws.
19) Connect the Blue wire from the relay to the Red wire in the wiring loom that has a white stripe and yellow or gold stripes.
20) Carry out steps 1 through 12 once more for the passenger-side headlight’s wiring. Test the lights after securing all exposed wires using zip ties. Embrace your brand-new LED angel eyes!
In This Article...
How do BMW Angel Eyes work?
Angel Eyes, commonly referred to as “halos,” are auxiliary lights that are added to or incorporated into the headlight assembly of a car in order to encircle the low-beam or high-beam lamp. They are merely decorative lights or lights to be utilized as daytime running lights; they do not take the place of the headlight or any other lights.
Many in the aftermarket industry coveted the distinctive aesthetic that was first created and debuted by BMW. As a result, there is now an abundance of lighting accessories that can be added to pre-existing headlights to get the same appearance. There are numerous varieties of angel eye parts available on the market that use various technologies to produce the “ring of light” look.
Is installing Angel Eyes simple?
Although you’ll need some simple equipment and an hour per headlamp, the task is doable by the majority of do-it-yourselfers and results in angel eyes right out of the box.
How do headlights with angel eyes function?
- Most automakers use standard halo rings that are lit by one or two incandescent lights, which create bright and dark patches inside the ring to provide the recognizable “angel eyes” look.
- Small cold cathode fluorescent lighting tubes used in CCFL halo headlights are filled with gas and burn cool, preventing hotspots and discolouration. Compared to traditional halo rings that are lit by incandescent bulbs, these rings are whiter and brighter.
- LED halo rings make use of powerful LEDs. LED halo rings can alter the light color on demand due to the peculiar properties of LED lights, which are constructed of layers of semiconductor material and can emit light of various hues depending on how these materials are chemically organized. Some colors are solely meant for off-road use because they don’t meet federal regulations and are therefore not street legal.
How are Halo headlights installed?
- Take off the screws from the headlight’s body.
- Warm up the headlight’s body.
- Take the Lens Off the Body.
- Light’s chrome housing should be removed.
- Set up the Halo Rings.
- Reinsert the Housing.
- Connect to Car Power Source
How can I tell if the lights on my BMW are xenon?
How can I know if a car has halogen or xenon lights? When the DRLs are on, the angel eyes around the lamps are xenon, and the LED eyebrows are also lighted.
Is installing Halo headlights challenging?
Halo projector headlamp installation is not difficult but can take several hours. This is only a basic guide for headlights; your specific set may differ. We always advise having a professional install our headlights.
1. Before working on your vehicle, put on safety gloves and eye protection.
2. It’s helpful to have a helper when removing the front bumper.
3. Cover the floor of your workspace with a mat to lessen the possibility of damaging or scratching your bumper or lights.
4. Until the device has cooled down, avoid making direct touch with the lights or wire assembly. Do not let any oils touch the bulbs.
5. Before installation, test the lights
Taking away the front bumper
2. Disconnect the headlamp assembly’s connectors.
3. Remove the headlight by first removing the five mounting bolts and harness clip.
4. Remove the headlight’s bolt and corner upper beam.
5. Attach the driving lights to the halo and LED wires.
c. You can also combine the black wires from the LED and Halo wires on the driving light’s ground wire (-). Connect the white wire from the LED and halo to the driving light’s positive (+) wire.
6. Replace the headlamp connectors.
7. Attach the headlights and mounting bolts.
8. Put the front bumper in place.
How can I tell if the headlights on my BMW are halogen or xenon?
Start your car, switch on the high lights, and then stand in front of one headlight for ten seconds while staring directly into it. It is a halogen if you are only half blind. It’s fantastic if you are fully blind.
Spectrum Angel Eyes: Are they legal?
Your car’s pre-installed headlights are designed for greater performance and to follow aerodynamic principles. Additionally, because they are pre-made, the producers can add running lights as well as signal or parking indicators. This results in the best possible use of the little available space in the car body. Additionally, they have access to a variety of lighting options, including as halos, projector beams, and LEDs.
The plastic lenses that are utilized in these headlights are prone to deterioration over time, despite the fact that they are a great fit for your car. They gradually erode from constant contact to road debris, eventually turning murky, discolored, and opaque. That would not be popular. You would? Not to mention the danger that you run while driving with poorer quality lighting.
They can definitely be fixed or modified to offer improved performance and stability. Your yellow car lights cannot be restored, despite all the advertisements and professionals who claim to be able to restore them to their previous illuminating qualities.
We have a fix now that you are aware of the issue and what can happen to your yellow lights in the future. The best headlights for a modern-day vehicle enthusiast are angel eye headlights.
Other options include halo headlights, projector headlights, and LED lights. They are simple to install and practical. Nevertheless, certain headlamp installations could need a few wiring adjustments. You may be sure that these unique headlights adhere to safety regulations and are completely legal.
The pattern of light reflection is what distinguishes projector headlights from conventional bulbs. A parabolic reflector used in conventional lighting will emit light in a dispersed pattern. In contrast, the light beam from a projector is altered by an elliptical reflector, which directs the light rays to a single focal point in front of the bulb.
The Angel Eyes halo lights are one of our store’s best draws. You may have seen the halo rings, sometimes known as led halo lights, that surround the primary headlight. The best part is that, like with our Angel Eye headlights, you may have a personalized colored halo ring light. You can choose any color you like, depending on your mood, by using a mobile application to operate these types of headlights.
Spectrum offers a wide selection of led headlights that are long-lasting and offer excellent nighttime visibility. Led lights often last 50,000 hours, and in addition to that, they produce a brighter, cleaner light than any other incandescent light.
How is a halo ring mounted?
- Tape from 3M should be used. On the underside of your halo ring, you can find 3M tape. Simply remove the film covering, mount, and then aim!
- Epoxy. Simply apply epoxy to the halo’s backside and adhere it to the chosen location.
- Apply the beading wire technique.
Why do LED headlights have three wires?
The ground of the single-wire LED light is standard. It takes place through the light housing’s bottom level. Also claimed to be single-functional are the lights. Every brake light and marker light are included. running or blinking lights.
Still capable of serving as a positive power wire is the one light. This has no effect on the color of the light; it might be red, white, or black.
It is used as single-function lights when using LEDs with 2 wires. It contains blinkers, running lights, marker lights, and brake lights.
Two wires would have one light that is positive and the other ground. The available and delivered wire would primarily be black or white. In this instance, ground is white and black light is positive.
LED lights become multi-purpose lights when they have three wires. The setup of the program will determine how the light is managed.
similar to brakes and blinkers, running and brakes, or blinkers and running. The cables are red, black, and white in hue. Black becomes the second positive and red the first. White light turns into the ground.
The blinker and brake are the finest applications for the three wire light. The relationship between LED and black lights and the positive brake lights of the car.
The car blinker is then connected to the red LED light. The flasher relay’s light output is better in the second connection.
Typically, the hues of the lights have no industry guidelines. To acquire the desired findings, test with a multimeter.
LED lights occasionally have some wiring system knowledge as well. The details are occasionally omitted.
- Finding the positive and negative ends of the wire is made easier by testing LED lights with a 9v battery.
Even if your LED light setup has three wires, this is still useful. Connect the predicted negative wire to the 9 volt battery’s negative side.
Connect the other side of the wire to the positive side of the 9-volt battery in a similar manner. Even if connections are incorrect by accident, the system won’t be harmed.