Could you please explain how to turn off the airbag light on my BMW X5? Every time I turn on my car, it has been coming on, and I have no idea how to turn it off. I’m hopeful that resetting the light will solve the problem.
In less than two minutes, find out if your auto insurance is being overcharged.
Unquestionably, resetting your airbag light is a solid first move. Observe these steps to reset the airbag light on your BMW X5:
- Upon starting your automobile, check to see if the airbag light is on.
- Then, after seven seconds, restart your vehicle.
- Two more times, repeat this procedure. Your airbag light ought to disappear.
It is advisable to have someone check over your car for you if the airbag light starts to illuminate once more. Given that sensors are frequently the subject of auto recalls, there may be an issue with the sensor or the airbag itself. The airbag will protect you and any passengers in the event of an accident.
The Jerry app makes sure you are prepared for the aftermath while airbag maintenance makes sure you are prepared for an accident.
The Jerry app, a registered broker that provides end-to-end support, compiles reasonable rates, assists you in switching plans, and even assists you in terminating your old policy.
In This Article...
Procedure
- Under the dash, you may find the OBD-2 port. Scanners can be connected to OBD2 ports. A 20 pin OBD2 adaptor is required if your BMW was manufactured in 2001 or earlier.
- Start the engine. Avoid starting the car.
- Scanner will start up. On the scanner, choose your BMW chassis/model. We are using a Foxwell NT510 from the BMW scanner in this instance.
- Choose BMW – Body – Safety System control units. You may read Airbag Fault Codes by navigating to the Safety System/SRS control unit.
- Clear the airbag control unit’s codes. revisit the first menu. To access Clear Fault Codes, scroll below. On the following screen, click YES.
Step 2: Use an OBD2 scanner to read the issue codes
Working with your airbag system is essential, therefore always use an OBD2 scanner to read the fault codes to determine where to begin troubleshooting. Never resolve the issue brought on by the airbag light before clearing the trouble codes. Continue the diagnostic by reading the codes to learn what might be the issue’s cause.
Resetting the Airbag Light (10 Simple Steps)
The airbag light connects the seat belt system and the airbag system as part of the Supplement Restraint System (SRS) in automobiles (and vice-versa). When you turn on your automobile, the airbag light comes on for around seven seconds before going out, signifying that the internal system check was successful and finished. When the airbag light either never turns on or stays on while blinking, an issue exists. The airbag light needs to be reset at this stage.
Examining seat belt components, fixing bad clock springs, and replacing faulty sensors are a few techniques for turning off an airbag light. New bulbs or a fully charged battery are other options. While most repairs can be done without a professional, others may.
The following 10 steps will reset your airbag light:
- Turn on and off your ignition.
- Test drive your car when it has been restarted.
- Check the airbag switch for the passenger.
- Check to see if the seat belts are in place and functioning properly.
- Check to see if the passenger seat sensor is off.
- Use a scanner with the ability to reset the SRS or airbag light.
- Fix the broken airbag sensors.
- Replace or repair a broken clock spring.
- Check to see if the airbag is working properly.
- seek for a specialist’s help.
Although not exhaustive, the list above includes tried-and-true methods for tackling the problem. Some of them might not apply to your vehicle because compatibility is always based on the year, make, and model. It is recommended that you have your service manual on hand when carrying out any of these fixes. Always follow the manufacturer’s recommendations, too. Let’s get started on resetting your airbag light right away.
Why is my BMW’s airbag light on?
What it appears to be: A passenger seated in a chair with a seatbelt fastened holding a circle in their lap. The “SRS” symbol is illuminated in the dash of some cars.
What it means is When a problem is identified by your BMW’s computers within the airbag control unit, the airbag system, or supplemental restraint system (SRS) light will illuminate. If the SRS warning light is on, the system has been turned off, and the airbags won’t inflate in the case of a collision.
What to do if it comes on: When a car starts up, this light will briefly illuminate in the dash before going off, signaling that everything is working as it should and making it safe to drive.
Check to see if anything is obstructing the seatbelt click switch or if anything is piled up behind the seat, which could harm the wires, if the SRS light remains illuminated after starting the car or while it is in motion. If nothing is discovered, visit a local independent BMW repair facility as soon as possible to have a professional inspect and identify the issue. This is not something to be taken lightly, and it is safer to get this issue looked at by a certified BMW mechanic than to jeopardize your safety and the safety of your passengers by driving while it is still active.
How to turn the light off: After you bring your BMW to your neighborhood BMW shop, your mechanic will examine the component and the wiring, run code checks, and perform any necessary repairs.
An illuminated SRS light may indicate a sensor issue, the need to reset your airbags (for instance, if you were recently in a collision and the sensors were activated but the airbags did not deploy), or an issue with the seatbelts. Checking car bulletins is a good idea because there may be other instances when your airbags need to be recalled.
How can I manually reset my airbag light?
When you experience the same problem, you should start by following this technique, which is identical to resetting the airbag light on a Toyota Camry. It needs timing the airbag light and has four straightforward stages that are simple to complete.
First, activate the ignition. Wait for the airbag light to turn on next; it typically illuminates for seven seconds before automatically turning off. After waiting three seconds, immediately flip the ignition switch off. Before starting the engine, go through the basic procedures a couple of times. Your car’s airbag light should illuminate for seven seconds before turning off permanently if everything is done correctly.
Why won’t my airbag light activate?
The backup battery is dead. It is the most frequent cause of an airbag light that won’t go off. It might take place if your car’s battery is running low or has been depleted for any other cause. Once the battery is fully recharged, the issue will be resolved. But the battery might still be in place.
Clear the airbag light with a CAN OBD scanner?
It’s time to reset the engine light when you have completely installed the new parts and are confident that everything is installed correctly. There is no other way to accomplish this; you must use an OBD2 scanner. Make that the airbag light is reset and that it no longer appears on the dashboard. Reread the codes and look for any trouble codes if the problem is still there.
Why does the light on my passenger airbag remain on?
A problem with the seatbelts or airbags is indicated by the airbag light. Therefore, it’s usually not a good idea to drive when the airbag light is on. We advise having it towed to the dealership rather than driving it yourself if it remains illuminated in your car.
What could turn on the airbag light?
The spring is intended to preserve continuity between the wiring and the driver’s airbag and coils throughout your steering wheel. The spring may wear out and fail over time, turning on the airbag warning light. Older autos are more likely to have this flaw.
The important line is that you must stop driving as soon as your airbag light illuminates and have your automobile inspected by a repair as soon as possible. Your airbags won’t activate until the issue is identified and remedied. Never disregard your airbag light since your safety and the safety of your passengers are top priorities.
Dashboard Warning Lights Explained, which offers guidance on a variety of lights and their meanings, is a good resource if you want to learn what additional warning lights represent and what to do when they illuminate.
What is the cost of turning the airbag light back on?
Reset Airbag Light, at No. 1 Although it typically costs a few hundred dollars and takes several hours, depending on the type of automobile it might cost as much as $600.
Driving while the airbag light is on is it safe?
No, driving while the airbag light is on is not safe. When the airbag light comes on, the vehicle’s airbag system is malfunctioning. Due to this flaw, the airbag is unlikely to deploy after an accident. Therefore, it is not advised that you use the vehicle until the system has been fixed.
Never disregard the important caution. There’s no need to gamble with the car, even though it doesn’t make it unsafe to drive.
The light does, however, show that the SRS parts are not functioning properly. This may potentially indicate that the airbags won’t activate in the event of a collision. You shouldn’t wait until you are involved in an accident to determine whether the airbags will keep you safe.
How are airbags turned off in cars?
To legally disable an airbag, you must make a written request to the NHTSA, and if it is granted, the work must be carried out by a licensed dealer or repair facility. When a car occupant does not fulfill the criteria for deactivation, they will install an on-off switch to enable the airbag.
Airbag module reset is possible?
After receiving your repaired module from us, you won’t need to take it to the dealership for additional programming because we reset all fault codes.
Except for modules that were harmed by a flood, fire, or another type of hardware damage, all airbag control modules can be reset and reprogrammed.
Accident-related hard and soft codes are stored in airbag control modules. The module that activates the airbag light will keep error codes even after minor incidents. To turn off the airbag light, we reset and erase all of these crash codes from the computer module.
Is the recall for BMW airbags free?
The issue: Due to propellant degradation brought on by prolonged exposure to high humidity, harsh temperatures, and temperature cycling, airbag inflators run the risk of exploding. In the event of an inflator explosion, the driver or other passengers may be seriously hurt or killed when sharp metal shards strike them.
The solution: Free of charge, BMW dealers will replace any defective airbags or airbag inflators.
How to get in touch with the manufacturer: The recalls should start on March 6, 2020. At 800-525-7417, owners can reach BMW customer support.
NHTSA campaign number: NHTSA’s recall number for driver-side airbag repairs is 20V017. NHTSA’s recall number for 3 Series cars that need passenger-side airbag repairs is 20V018. NHTSA’s recall number for X5 and X6 SUV passenger-side airbag repairs is 20V016.
To see if your car is still subject to a recall, check: You may find out whether there are any open recalls for your car on the NHTSA website.
If you enter the 17-digit VIN of your automobile onto the NHTSA website and a recall doesn’t show up, your vehicle is not currently subject to any open recalls. We advise checking back frequently to determine whether your car has received a recall because automakers frequently issue recalls and for many older vehicles.
Utilize our Car Recall Tracker to stay up to date on recalls that may apply to your car. To join CR, open a free account right away.
Although I adore quirky, vintage European sedans like the Renault Medallion, it is my passion to assist people in finding a car that is safe, dependable, and still makes them smile—even when they’re caught in traffic. You can usually find me planning my next vacation or exploring a new city on foot when I’m not behind the vehicle or at the computer.