The “brake” light on your dashboard or iDrive system is controlled by your BMW brake pad sensor, which also informs you of the remaining life of your brake pads. The sensor is mounted to the brake pad; as soon as the brake pads are completely worn down, the sensor’s tip breaks, tripping the wire and turning on the dashboard light. The brake pad sensor error codes are as follows when using an OBD scanner:
In This Article...
5, 5, 6, 5, 14, 5, 15, and 6F12
Every time you change your brake pads, you should also replace the brake pad sensor. The sensor does not need to be changed every time, but failing to do so could lead to erroneous readings of the amount of life left in your pads and a persistent notification on your dash/iDrive system. The only way to get rid of the light once it appears on the dash is to either swap out the sensor or bypass it, which will stop it from reading the pad life.
PAX5
It’s frightening. With only two years old and 26k miles on the odometer, I never considered checking the brake wear so soon.
Is taking the wheel off and completely disassembling it like I would to replace brake pads and rotors the quickest and easiest way to check brake wear? How can I gauge the thickness of a rotor? Brakes are crucial, so I’ll start performing my own inspections. I require a map.
Pads and rotors are ALWAYS substituted for brake sensors. It is a two-stage sensor that needs to be calibrated or initiated when new. Once the sensor begins to rub against the rotor, this is accomplished by a copper contact in the sensor.
Remove the wheels to check the brake pads’ and the rotors’ thickness using a digital caliper. The ONLY way to obtain actual readings that are correct… alternatively, after gaining some expertise, you may “eye-ball” them…
Can the brake pad wear sensor be bypassed?
By removing the brake wear sensor, adding a clip, or cutting the sensor cable to expose the wires and link them, many BMW owners opt to bypass (remove) the brake wear sensor.
This emulates a “good” sensor and is referred to as short-circuiting the wire, however it is not advised.
You won’t know when to replace your brakes if you don’t use the brake pad wear sensor. Up until they touch the metal component, your brake pads will wear entirely, resulting in metal-on-metal contact.
In addition to having less stopping power, you will also experience a grinding sound, damage to your rotors, and need to replace them.
How much does a BMW brake sensor replacement cost?
Replacement brake pressure sensors for a BMW 328i typically cost between $254 and $265. Between $44 to $56 is the projected cost of labor, while the cost of parts is $210. Taxes and levies are not included in this range, nor are your particular model year or special location taken into account.
How can a BMW brake sensor be reset?
My car’s brakes were recently changed by my uncle, but the warning light is still on. Does a BMW X3 have a mechanism to reset the brake light?
In less than two minutes, find out if your auto insurance is being overcharged.
Every time the brakes and brake wear sensors are replaced on a BMW X3, the brake light warning must be reset. Fortunately, the brake light reset is simple and should only take a few minutes.
Resetting the brake light on a BMW X3 is made simple by:
- Do not start the engine after turning the ignition to the on position.
- Wait 30 seconds before opening the driver’s side door.
- Wait another 30 seconds after switching the ignition to the off position.
- start the vehicle
If the aforementioned fails, you should:
- Don’t start the engine after turning the ignition on.
- Up until the service menu appears, keep holding down the trip reset or odometer button. The service menu should show after holding the button pressed on the left side of the speedometer for approximately ten seconds.
- To find the brake warnings, use the reset button or, depending on the model, the controls on the turn signal lever to navigate through the settings.
- When prompted to reset the warning, press and hold the reset or BC button on the end of the turn signal lever.
- When prompted, press the reset or BC button once the screen indicates that it is resetting.
Finding auto insurance shouldn’t be a headache, but dealing with unnecessary warning lights can be.
Jerry is a helpful software that compares quotes from more than 50 leading insurance companies in a couple of seconds. When you locate an insurance you prefer, Jerry can assist with the transition and paperwork. It’s that simple!
How do BMW brake sensors function?
It functions by detecting resistance.
Due to its dual stage design, the sensor contains two wires that, when worn through, alter the resistance readings. It now has a two stage wear indication warning.
No, it won’t be harmed. It will be duped into believing it has all of its defenses. However, you will need to perform a reset operation if it is already displaying a brake warning. Try searching. I haven’t done it in a long, so I can’t recall the exact instructions.
No, I’ve got old sensors whose wires I cut off and bridge together. Since they don’t have slots for the sensors and would probably melt at the track, I use them when I have my track pads in.
Technically, since you’re shorting it, there won’t be any resistance. I’d advise starting early.
As I recall, it is at around 2000 ohms. You don’t need to add a resistor, despite what you might be thinking. To complete the circuit, simply connect the two wires together. I personally prefer to invest in new sensors, although I have occasionally cheated to get myself out of a problem. You might be overanalyzing things.
It was said to be less than 1 ohm yet larger than zero in some information I came across. I wouldn’t get close to the full mileage if I reset after going through the wires. Maybe this is brought on by having a lower resistance than new? If no one else has ordered these before, I’ll get some additional ones to check at some point.
It was probably a few years and a few beers ago, but I think I cut one open and it was just a thin copper strand that, once broken through wear, began a countdown with the automobile. It is enclosed in plastic because any resistance would generate heat and load. Anything below an ohm is a closed loop, and your probes’ minimal resistance is all that your meter is picking up from them.
Does BMW have a sensor for brake pads?
Recent releases from numerous German manufacturers, notably BMW, have a two-stage pad wear sensor (See Figure 3). The driver can receive more information from these sensors than just a worn brake pad alert. They can actually calculate the remaining mileage of a brake pad.
BMW brake wear sensors: are they recyclable?
Electronic brake pad wear sensors are now installed in a wide range of contemporary vehicles, especially European vehicles. They inform you when it’s time to replace your brake pads with a brand-new set. But how do they function? And how frequently do they require replacement?
The conventional metal squealer tabs that are more frequently used in braking systems are replaced by electronic brake pad wear sensors. When the pads have reached the end of their useful life, these tabs continue to function by rubbing against the rotor. It alerts the driver that the brakes need maintenance by emitting a loud screech.
In addition to the scream, this has the drawback that most drivers tend to ignore the warning since they believe the sound will ultimately stop. Electronic brake wear sensors take care of this noise and provide a more precise indication of the remaining life of the brake pads.
Once the brake pad has worn sufficiently for the sensor to make contact with the brake rotor, the wear sensors are intended to break or complete a circuit. The dash will typically illuminate with a warning light when the brake pads need to be changed.
Basic brake wear systems typically implant a sensor inside the inner brake pad at each corner of the car. However, from vehicle to vehicle, the number of wheels with sensors and their positioning on the brake pad can differ. These systems merely have a wire loop that is conducting a little amount of current.
Brake wear sensors in the modern day have a few new tricks up their sleeves. Not only do they alert the driver when brake maintenance is necessary, but they can also predict how long your existing brake pads will last. These ruse sensors, sometimes termed as twostage sensors, operate with two parallel resistor circuits at two depths. The resistance in the sensor rises as the initial resistive circuit fails. In order to determine how much life is still left in your brake pads, this is utilized to collect data such as wheel speed, brake pressure, brake disc temperature, brake operation time, and mileage. This is typically shown in the information center of your automobile or as a warning light that changes color as the pad ages. The circuit becomes open when the second circuit is disrupted. This sets off the brake service indicator light, alerting you that it’s time.
Braking pad wear sensors are not reusable because they are made to break or complete a circuit by making contact with the brake rotor. With each change of brake pads, wear sensors for the brakes should be updated. To fit a variety of automobiles, Bendix offers brake pad wear sensors. For the majority of common makes, our Bendix Euro+ Brake Pads also include all required clips, shims, and sensors, so you’ll be ready for your upcoming brake pad replacement. At your next service, request Bendix brakes from your mechanic.
The majority of popular makes and models are guaranteed to fit with Bendix’s brake wear sensors. Visit to determine if your local Bendix stockist has brake sensors that will work with your vehicle.
Do the braking sensors need to be replaced?
Since brake pad wear sensors are made to malfunction, they should always be replaced whenever new brake pads are installed. In between changing pads, it’s also a good idea to frequently inspect the sensors and replace them as needed. Heat from the brakes can harm the wire and clips over time.
The accuracy of the BMW brake pad sensor
It is very accurate if installed properly since it needs to be changed when the minimum level is reached because it wears out. You shouldn’t be concerned until your car shakes noticeably when you brake.
Can you reuse a brake sensor?
The sensors are located on the front and back brakes. They must to be changed each time you switch pads. You can reuse the pads if they haven’t worn down to the sensor.
Why is a brake sensor necessary?
The brake pad wear sensor provides the driver with reliable information regarding the brake pad’s current state of wear. One sensor for the front axle and one sensor for the back can be mounted in the brake pad to detect and alert the driver when a replacement is necessary.
What is the price of a braking sensor?
Aftermarket pad sensors can cost anything from $5 to $100. Additionally, you should budget an additional labor expense of $70 to $100 if you decide to hire a professional brake work.
A new sensor can also cost more due to a number of factors, including:
- Make and model of the vehicle
- Brand and series of brake pad sensors
- Warranty for brake sensors
- Sensor pad length
- elements of worn sensors
- in which you reside