Under the spare tire on the Audi A4, you’ll find the battery. Pull up the floor panel after opening the trunk. Pull up the spare tire after counterclockwise-twisting the huge wingnut. The spare tire tray should be raised and placed aside.
In This Article...
I need to jumpstart my Audi.
How to Jump Start a Battery with an Audi A4 B7
- First, attach the positive cord. Connect the positive cable to the positive battery terminal of the running vehicle, then to the positive battery terminal of the non-running vehicle.
- 2. Attach the negative cord.
- Start the car in Step 3.
Where is my car’s battery?
Varied vehicles have different locations for the car batteries. The battery is often kept in one of the front corners of most models’ bonnets. To equalize weight distribution, some batteries are placed in the trunk of the vehicle. To learn where the battery is located in your specific model, consult the owner’s manual.
After consulting your manual, it should be simple to locate the car battery. Look for a black battery in the form of a box with two sizable cables attached to the top. The positive and negative electrical terminals are represented by these cables. You shouldn’t be able to overlook your car battery since most automobile batteries are about 6 by 10 inches in size.
Here are several things that can shorten your battery’s lifespan if you’re concerned about its health.
The Audi A4’s battery location is unknown.
Even though the B7 just upgraded the prior generation, it was still fundamentally a 2000 model year vehicle. The new MLP platform, which enables a larger wheelbase without increasing the vehicle’s total length, is one factor that helped make the A4 B8 a considerable design improvement and a huge step forward.
Better handling, steering, and ride comfort are the outcomes, with a weight distribution of 55:45. There is a lot more room in the rear row thanks to the 6.3-inch increase in wheelbase length. Despite receiving a mixed response at delivery, the A4 B8 went on to become one of the most well-liked vehicles in its class. It had a redesign in 2012 that kept it current until 2016, when the current generation took its place.
The battery was eventually relocated by Audi’s engineers, although it is now found inside the trunk as opposed to the engine bay. Pull up the carpeting part to obtain access, then use the built-in hook to keep it lifted. Remove the space-saving tire from the trunk by removing the lid keeping it in place.
Before the battery is fully exposed, a protective plastic and foam must be removed. You still have work to do because you need to remove the metal plate covering the battery to keep it safe from the spare tire. You can finally access the battery cover and terminals once you’ve removed it.
To be quite honest, after going through that procedure twiceonce to remove the battery and again to replace itI don’t mind working up a sweat when doing it on my B6. The new procedure takes longer, but it requires less physical effort, which is more crucial because it lowers the possibility of damaging something or hurting yourself.
On an Audi A4, where do jumper cables go?
1. Join the lead’s one end to the jump-start terminal shown in Figure 279 1 (terminal).
2. Join the other end of the positive lead to terminal 2 of the positive battery.
3. Join the negative lead’s other end to the boosting device’s negative terminal 3.
4. Attach the lead’s other end to the jumper terminal 4 (the terminal with the
Do not run the starter for more than 10 seconds if the engine won’t start.
Connect the leads in the exact opposite order while the engine is running.
- The battery clamps’ non-insulated components must not be permitted to touch.
- Avoid bending over batteries to avoid acid burns.
- The battery cells’ screw plugs must be tightly screwed in.
- Keep lit cigarettes, sparks, and flames away from batteries as the gases could ignite.
- Position the jump leads so when jump-starting another car.
that nothing moving in the engine compartment can come into contact with them
Observe that the leads should only be connected using the aforesaid approach for jump-starting
your automobile. You shouldn’t connect the negative if you’re jump-starting another vehicle.
engine block or an object made of solid metal that is fastened to the engine block. In the event that the
Since the other car lacks a gas vent, there is a possibility that a mixture of oxygen
How can I jump-start a dead battery in my car?
- Place the vehicle you’ll be using for a jumpstart next to the vehicle with a dead battery, close enough for the cables to reach. The cars shouldn’t be in contact with one another.
- Switch off the engines of both vehicles.
- Clamp the positive cable’s first end to the positive clamp on the dead battery.
- Now have a buddy attach the other end of that cable to the positive clamp of the other battery.
- Next, attach the negative cable to the good battery’s negative terminal.
- The other end of the negative line should then be connected to a ground on the car that has the dead battery. The engine block or similar metal surface far from the battery can serve as this. While doing this, take care not to touch the cable’s two ends together.
- Launch the emergency vehicle that is supplying the electricity.
- With the weak battery, start the vehicle. Check your connections and tighten or clean them as necessary if it won’t start.
- If the problem vehicle does manage to start, let it run for at least 20 minutes to give the battery time to recharge before turning it off.
- If it still won’t start, there might be an additional issue. For assistance, dial a nearby service station.
- Reverse the order of the cables’ disconnection.
How can a 2017 Audi A4 be jumpstarted?
Negative lead (black) should have one end connected to the negative terminal (-3) of the boosting battery (A). The jump-start terminal -4- (terminal with hexagon = “negative”) of the car with the flat battery -B- should be connected to the other end of the negative lead (black).