You can still install the battery yourself, but you’ll need to either take it to the dealer or reprogram the computer using diagnostic software like VCDS.
In This Article...
Is programming of the Audi battery required?
This tool is used to register the new battery in the on-board computer if the system is open. Even automobiles equipped with BEM can configure the recently purchased replacement battery in a closed system. Additionally, error codes that are common or manufacturer-specific are typically read from the system or removed. This is true even if there was a voltage drop during battery replacement or if the car’s on-board computer was unplugged.
The Banner Battery Service Tool (BBST) can generate the Battery Energy Management code (BEM code) even for Audi models, which, in contrast to other brands, always request a code when changing batteries. This ensures that the battery change is properly recorded and that various functions are not restricted. The Banner Battery Service Tool (BBST) also has a system check that examines the entire charging system, including the battery and alternator, and it has a built-in product search to help you select the right replacement battery.
Only the configuration or actual values of the old battery stored in the control unit are reset by entering the BEM code, and the current mileage is saved.
It’s crucial that you utilize the Memory Saver together with the Banner Battery Service Tool (BBST):
The power source of the electrical system must be externally powered, for example using a Memory Saver, to prevent the deletion of vehicle settings and codes when batteries are changed. Car data loss can be safely avoided by maintaining voltage via the OBD (On Board Diagnostic) socket in the vehicle. Vehicle information, such as the navigation settings, phone book, radio station, electronic seat position, etc. are remembered when the battery is changed. Another benefit is that, when using the Memory Saver to replace a battery, re-registering is typically not required.
It is not problematic to use a Memory Saver for voltage management and a Banner Battery Service Tool (BBST) simultaneously because the included adapter makes it simple to connect both devices.
The car system logs the failed battery for an older battery. Without a BEM code, the vehicle won’t recognize that a new battery has been installed if one is installed. To inform the energy management system of the new battery’s status, a BEM code must be entered, or the new battery must be initialized using a multi-brand diagnostic tool, such as the Banner Battery Service Tool (BBST). The system must initially configure the new battery condition if neither is available. The system picks this up more quickly the more “trigger events” (impulses, signals, such as starts, cold starts, and cycles) there are in the battery. The amount of time it will take depends on the manufacturer’s specs. It can last anything from two operating hours to six days. Within a few hours, the vehicle computer often gradually unleashes the previously restrained systems, such as the air conditioning system’s full power. The error memory may take longer to reset visible error messages. It often takes a few days (up to 6 days depending on the manufacturer) for the system to detect the new battery status and reset the error signals if this is not done actively through a Banner Battery Service Tool (BBST).
More and more automakers advise or demand that the system configure the new battery. Then, you must go to a mechanic so that a diagnostic tool may alert the energy management system that a new battery is in place and that the stored data are reset. These days, this so-called initialisation may be completed for many different auto models using multi-brand diagnostic instruments, such as our Banner Battery Service Tool (BBST). The control unit often keeps track of the mileage at the time the battery is replaced in addition to resetting the configuration or actual values for the old battery.
Conclusion: The only immediate benefit of purchasing and BEM coding an original replacement battery over a battery from an independent aftermarket that does not have BEM coding is that all systems are immediately functional. Please take note that the battery often achieves this functionality without a BEM code after a period of time and a number of trigger events (impulses, signals, e.g. starts, cold starts, cycles).
Even without entering a BEM code, installing a high-quality replacement battery eliminates any safety risks, overcharging concerns with the new battery, increased battery wear, and potential damage to the vehicle’s electronics or other components. These days, this so-called initialization process can be completed for multiple auto models using multi-brand diagnostic instruments, such as the Banner Battery Service Tool (BBST).
Please be aware:
In a car with a start-stop function that comes standard with an EFB or AGM battery, never install a normal wet-cell battery. If more power is required, an EFB or AGM battery must be utilized. in the same housing unit and in the same performance category.
PS: Minor variations in capacity or performance during a cold start have no impact on the electrical system’s safe start and optimal power delivery.
It is crucial that the new battery is set up in the system for start-stop vehicles with a battery energy management system when switching from EFB to AGM batteries (BEM). This is the perfect use for the Banner Battery Service Tool (BBST).
Banner advice for luxury and upper-class vehicles:
Particularly with two-battery car electrical systems, the disconnection sequence must be strictly followed while removing the old battery (or batteries), as failure to do so could trigger the safety battery contacts. According to the operating instructions, for example on a VW Phaeton V10 TDI, you must first detach the left-hand AGM battery and then the right-hand conventional wet-cell battery in this situation (our test car was built in 2006).
The proper equipment for replacing start-stop batteries is:
- Automatic creation of the battery energy management code particular to the manufacturer (BEM)
- reading and erasing error codes particular to a manufacturer
- Battery, starting power, and charging system evaluation
- Textual explanation with illustrations showing where to place the OBD diagnosis plug
- Y adapter for Banner Memory Saver wiring system voltage retention (optional)
- Battery allocation: Includes 30,000 utility vehicles and more than 41,000 autos.
Should I reprogramme my car after changing the battery?
Yes. Your settings will need to be reset. The dealer will typically do it for free, but no guarantees can be made. If you replace a battery and anything was connected to the old one, such as the hose you mentioned, you must reinstall it. Everything is always put back on the same way I took it off. If you find yourself in need of help, think about calling YourMechanic. One of our mobile specialists may visit your house to service your batteries and make sure it was installed correctly. Thanks for reading, and good luck.
What should I do after changing my car’s battery?
wonderful question In order for the alternator to properly charge the battery after a car battery replacement, you should drive the vehicle for roughly 30 minutes.
A battery replacement typically necessitates a radio and computer reset on the car. Your radio presets may need to be reset as a result of this.
After changing the battery, the computer occasionally does not restart itself. The dashboard may still display an error code. Use an OBD-II diagnostic scanner to identify the issue’s root cause in this circumstance. You can reset the computer by looking up the code.
You can *clean the battery terminals with a wire brush and battery cleanser every six months** to extend the life of your new battery. When you can, park in a garage to shield your battery from chilly temperatures.
As a heads up, batteries often last for five years. Although experts advise buying a new battery every three to four years, many last far longer.
How do I reprogramme my vehicle after a battery change?
- To allow the engine control systems to detect any potential issues, drive the automobile for at least 10 kilometers.
- The check engine light will illuminate if there are any problems, and the electronic control module is probably to blame.
- You’re good to go if the light doesn’t turn on.
Check out Jerry app if you want to look at a good way to enhance your car’s insurance policy now that the battery has been changed. We will provide you with individualized quotations from leading insurers in a matter of seconds, allowing you to simply choose the strategy that best suits your needs. And after you choose one, we’ll even assist you with switching!
How much does a new Audi Q7 battery cost?
Audi Q7 batteries typically cost between $416 and $444 to replace. Between $108 and $136 is projected to be the cost of labor, while $308 is the cost of the parts.
The lifespan of the Audi Q7’s battery.
The average battery life for a 2017 Audi Q7 is three to five years, however this might vary based on the battery, the environment, the driver’s behavior, and other factors. By: Regularly testing your battery, you can increase the lifespan of your Q7 battery. storing your car indoors, away from climates or extreme temperature changes.
In a 2014 Audi Q7, where is the battery located?
The driver’s seat must be removed in order to access the battery, which is located underneath. First, scoot the seat as far forward as you can, then use a flat head screwdriver to pry up the assembly cover on the side of the seat. Move the seat back as far as it will go after removing the seat’s rear fasteners.
Can a jumper be used on an Audi Q7?
Your Audi Q5 or Q7 can be jumped, allowing you to resume driving in a matter of minutes. Continue reading to find out how to fast start a dead battery.