If you are jacking up the front wheel, the jack goes directly behind it; if you are jacking up the rear wheel, the jack goes directly in front of it. There ought to be a small mark along the rail. Start elevating the car after positioning the jack beneath the location. Lift the car high enough for a jack stand to fit beneath.
In This Article...
The jack in an Audi A4 is where?
- On a solid, flat surface, park the car as far away from oncoming traffic as you can.
- Turn on the parking brake.
- Turn on the hazard lights.
If there are any passengers in your car, ask them to get out and go somewhere safe.
Audi A4 Flat Tire Equipment
You should have a vehicle tool kit, tire mobility kit, and vehicle jack in your car, all of which may be found in the trunk’s luggage area underneath the cargo floor cover (trunk).
- Pull the strap holding the cargo floor cover up to reveal the front compartment (1).
- Pick up the cargo floor by the plastic handle to access the rear compartment (2).
- (2) Secure the plastic handle to the seal on the baggage compartment
- Pull the plastic lever of the cargo floor toward the back to completely remove it (2).
- If your car has a spare tire, turn the handle in the other direction to take it off.
- Before locking the lead on your trunk, unhook the cargo floor.
Depending on the vehicle’s accessories, the compressor, tire mobility kit, and tool kit may all be concealed under a different cover that is fastened with a hand wheel.
If your vehicle has a storage bag for the jack, the storage bag is fastened with tie-straps in the baggage area and needs to be fastened again after use.
Using The 2020 Audi A4 Tire Mobility Kit
The use of slime to inflate a flat tire is only a temporary solution. If feasible, replace the damaged tire right away. Never remove a nail or other sharp object that has punctured a tire from the tire. Temperatures as low as (-4F) or below can be used with the tire mobility kit (-20C).
Where is the Audi A4 toolkit?
Some Audi A4s have an additional cover, maybe with a knob, that conceals the tools, compressor, and tire repair kit. The tool kit can be found behind the back seats of some Audi A4s, right behind the floor panel (Fig. 2A).
How is an Audi a8 jacked up?
Always give the jack* a stable platform on the ground. (The tool set for the Audi A8 has the jack.) Use a sizable, sturdy board or another type of support if necessary. To stop the jack from slipping on a hard, slippery surface (like tiles), use a rubber pad or something comparable. WARNING!.
Find the marking (recess) on the door sill that is nearest to the wheel that has to be replaced. Fig. 1. The indication under the door sill is in front of the jacking point.
The cylindrical portion of the arm of the jack’s arm, shown in Fig. 2 (A), should be below the provided plastic socket as you wind up the jack* under the jacking point.
Align the jack* so that the movable base plate of the jack (B) is flat on the ground and the cylindrical section of the arm (A) fits in the plastic mount under the door sill. The jacking point (A) must be supported vertically by the base plate (B).
- Verify the jack’s stability. The jack runs the risk of slipping or sinking in if the ground beneath it is slick or mushy.
- To elevate the Audi A8, just use the jack* that came with the vehicle. A other Audi A8’s jack could not fit your Audi A8, which could be dangerous.
- Only use the jack* at the jacking points that are behind the door sill markings, and make sure it is properly aligned. If the jack* is not correctly engaged, there is a danger of damage since it may suddenly slip off.
- Variations in temperature and load can cause the height of the parked Audi A8 to fluctuate on Audi A8s with adaptive air suspension/adaptive air suspension sport*.
- Never start the Audi A8’s engine when it’s in danger of colliding!
- If work is to be done underneath the Audi A8, make sure it is securely supported on appropriate stands to reduce harm risk!
It is forbidden to raise the Audi A8 on its sills. The Audi A8 may sustain damage if the jack isn’t used at the jacking points that are behind the markings on the door sill.
On an Audi A5, where do you mount the jack?
Put the vehicle in first gear (manual transmission) or position P on the selector lever (automatic gearbox).
Find the marking (recess) on the door sill that is nearest to the wheel that has to be replaced. Fig. 1. The marker on the door sill is in front of the jacking point.
Turn the jack up until the claw completely encircles the seam on your Audi A5 (Fig. 2 -A).
Place the jack in the proper position so that the claw of the jack (A) fits around the seam and the jack (Bmovable )’s base plate is flat on the ground. The jacking point (A) must be supported vertically by the base plate (B).
In order to attach the crank handle to the jack, place it inside the knob’s opening. To fix the crank handle in place, turn it either clockwise or counterclockwise.
Wind the crank handle to raise the Audi A5 till the problematic wheel is off the ground.
Only the jacking points indicated on the door sill in Fig. 2 may be used. Each wheel has its own jacking point. Apply the jack only where indicated. Caution!.
The Audi A5 may fall off the jack if there was an unstable surface underneath it. Always provide the jack a stable basis to stand on. Use a sizable, sturdy board or another type of support if necessary. To keep the jack from slipping on a hard, slippery surface (like tiles), use a rubber pad or something comparable.
- Reduce the danger of damage by keeping the jack’s base from slipping.
- Only position it and apply the jack at the proper jacking places. The Audi A5 could roll off the jack and cause injury if it is not placed firmly.
It is forbidden to raise the Audi A5 on its sills. The Audi A5 may sustain damage if the jack isn’t used at the jacking points that are behind the markings on the door sill.
Where is the jack in the 2017 Audi A4?
Always give the jack* a stable platform on the ground. (The vehicle’s tool kit has the jack.) Use a sizable, sturdy board or another type of support if necessary. To stop the jack from slipping on a hard, slippery surface (like tiles), use a rubber pad or something comparable.
Find the Fig. 315o indication on the door sill that is closest to the wheel that needs to be changed. The indication under the door sill is in front of the jacking point.
When the jack’s claw completely encircles the seam on your car, turn the knob to wind up the jack* underneath the jacking point on the door sill.
Place the jack* so that its base plate is flat on the ground and its claw (A) fits around the seam. The jacking point (A) must be supported vertically by the base plate (B).
Now attach the crank handle to the jack by fitting it into the knob’s aperture. To fix the crank handle in place, turn it either clockwise or counterclockwise.
Wind the crank handle to raise the car till the broken wheel is off the ground.
- To raise the car, only use the jack* that came with it. The risk of injury increases if you use a jack from another vehicle because your car can slide off the jack.
- Never start the engine when the chance of an accident is high!
- If work is to be done below the vehicle, make sure it is securely supported on appropriate supports to reduce harm risk!
It is forbidden to raise the car on its sills. Only use the jack* at the jacking locations that are behind the door sill markings. In the absence of that, your car can be harmed.
Has the Audi A4 got a spare tire?
As the majority of you are aware, newer Audis do not have a spare wheel (not even a space saver one). The only option offered is an inflated kit, which is essentially useless and, when used, damages the tire, necessitating the purchase of a new tire each time a puncture occurs.