The first step in having your check engine light diagnosed is knowing where to plug in your car code reader. These connectors are always present within the automobile, even if the OBD2 port’s placement can change depending on the make and model of your car.
The OBD2 port on your car is often located under the driver’s side dashboard.
The connector is typically found on the driver’s side of cars under the instrument panel, also known as the dashboard, while some cars have them in the center console or even on the passenger side. Additionally, some OBD2 ports are visible and simple to locate, while others are covered. Remember that since the connector is under the dash, getting low enough to locate it and connect your scan tool would probably require getting out of the car.
Consult your owner’s manual or type your vehicle’s information into our OBD2 port locator if you’re still having trouble finding your OBD2 port.
In This Article...
Where is the Honda Accord’s diagnostic port located?
The location of the Honda Accord 8’s OBD connector (2007 – 2015)
- Under the steering wheel, in the fuse box, is the OBD2 socket.
- The hood lever is next to the OBD socket.
- The diagnostics port is visible close to the fuses.
OBD1: What is it?
Let’s first go over the definition of OBD in greater detail. The term “OBD” stands for “on-board diagnostics.” The second iteration of the onboard diagnostic system is known as OBD2.
The system in an automobile known as OBD, or onboard diagnostics, is responsible for monitoring and controlling all significant control devices while providing data access with the proper hardware and software.
The capacity of OBD to alert the reader to any fault codes or unusual actions with their car is an essential component. Diagnostic issue codes or fault codes are the names for these mistakes.
Normally, when a system error is discovered, it records the necessary error code in its memory and displays a warning light on the dashboard of the vehicle. This is what typically occurs when the bothersome check engine light comes on.
OBD 1The Predecessor
OBD1 was developed in the USA as a response to initiatives to lessen air pollution brought on by a rise in the number of cars in major cities. With the introduction of tighter pollution standards for gasoline-powered automobiles by the California Air Resources Board (CARB) in 1988, California took the lead in the effort to “keep the air clean.” Compliance was necessary for the duration of the vehicle, not simply while it was brand-new.
It was necessary to create an electronic self-monitoring system to enable compliance checks at any time, which led to the development of OBD1. The user was informed of an abnormal situation via a signal light.
It was adopted in 1994 by other states. However, OBD1’s largest flaw was non-standardization, as automakers developed and used their own methods, necessitating the need of numerous scanners to read various systems.
OBD2The Current Standard
The newly created OBD2 system was required to be installed in all new automobiles beginning in 1996 by CARB legislation, which was established in 1994. By using a common interface, this would enable the usage of a single OBD scanner across many automakers.
By doing this, it would be possible to monitor not only emissions regulations but also the entire exhaust-influencing system, which includes all of the many operations in a vehicle. The standardization produced a simpler trouble code reading process.
Via the year 2000, OBD2 had arrived in Europe, mandating that any emissions violations be notified by a dashboard warning light and error codes stored by the car.
Since 2001, all automobiles with Otto engines (petrol/gas engines) are required to have the OBD2 interface. Beginning in 2004, diesel automobiles were subject to these requirements.
Both auto repair shops and automobile aficionados found the new standard to be quite helpful. OBD scans can be expensive in terms of both time and money.
However, most individuals aren’t aware that OBD2 scanners are available for personal use, giving them complete control over their vehicle and repair costs.
OBD2 Scanner: How do I use it?
Your vehicle is identified with a VIN (VIN). You may need to enter the VIN before your scanner can generate any OBD2 codes, depending on the scanner.
Other information, such as your engine and model type, may also be requested by the code scanner.
The VIN can usually be found on a sticker in the lower corner of the driver’s side windshield, if the scanner asks for it. Other locations are in the front of the car’s frame and under the hood near to the clasp.
What distinguishes my car between OBD1 and OBD2?
Your car may only have a limited amount of information if it eventually has OBD1. Additionally, because different car brands did not use the same communication protocol, you will need a distinct tool for each brand. Please refer to this post to learn more about the OBD1 scan tools we have.
There are two (2) questions you should ask to determine whether a car is OBD2-compliant so you may quickly access vehicle data using a typical scan tool:
- Was your vehicle built prior to 1995? If so, your vehicle will have OBD1.
- Does the OBD plug on your car resemble the one below? If so, your vehicle is OBD2 (And might be fully OBD2 compliant). If the plug looks different, it was produced before 1995 and is OBD1.
(However, some vehicles made between 1995 and 2005 may have a plug similar to the one shown above but that plug cannot be easily accessed because those vehicles did not have the whole OBD2 protocol.)
Australia imports the majority of its automobiles from Europe, Japan, or, in the case of specific models, Australia.
How many OBD2 ports are there in a car?
A automobile you bought after 1996 is likely to have an OBD-II port. But what is it used for, and how does it work for mistake diagnosis?
It’s likely that your vehicle has an OBD-II (Onboard Diagnostics II) port if you bought it after 1996. After 1996, it became required by law to put one in every automobile and truck on the road.
An onboard computer called OBD-II keeps track of your car’s emissions, mileage, speed, and other information. It is associated with the Check Engine light, which turns on when a problem is found by the computer.
Under the driver’s side dash is a 16-pin port for the OBD-II onboard computer. It enables the use of a special scan tool by a mechanic or anybody else to read the fault code.
Can I drive when the OBD2 is connected?
Sorry to hear that your car is having problems! While driving, leaving an OBD2 scanning tool connected in is quite safe. In order to prevent harming the scanning software, it is crucial to have your automobile running while diagnosing an engine code.
Concerned about the life of your car’s batteries? Unless you leave your OBD2 scanner plugged in and don’t drive your car for several days, driving while it’s connected does not considerably drain the batteries. Unplug the scanner if you know you won’t be driving for more than a few days.
OBD2 scanners are getting more advanced because they include Bluetooth technology. However, just as with the older generations, you must be very careful when plugging and unplugging the scanner during operation.
The 16 pins on the plug allow the scanner to connect to the OBD2 port on your car. You should be careful not to bend or shatter the pins while installing the scanner because they are quite delicate. Do not insert a pin into the OBD2 port if it seems to be ragged or bent.
Simply download the app, respond to a few short questions, and you may browse the most affordable rates from more than 50 reputable insurance providers in under a minute. Jerry users save $887 annually on car insurance on average!
A 2016 Honda Accord does not have an OBD port.
The location of the Honda Accord 9’s OBD connector (2012 – 2019)
- Over the pedals is where you’ll find the OBD II socket.
- Over the footrest is the OBD plus.
- OBD port is located here.
How can the codes on a 1995 Honda Accord be checked?
Okay, I ran a scan to determine the cause of the check engine light on my Honda Accord. It was discovered to be the EGR valve. I replaced the EGR valve, but now that I’m driving it, the check engine light just comes on, making it impossible for me to see what the fault code is. I attempted to reset the ECU, but nothing happened. The battery that also didn’t work was unplugged. I have to pass the smog test, but I’m not sure how.
Answer:
You can obtain the trouble code(s) for your Honda Accord on your own by connecting a jumper wire to the diagnostic connector that is situated in the kick panel on the passenger side. Place the jumper wire between pins 1 and 2 of the 2 PIN service connector. Moreover, you ought to notice a 3 PIN connector. A trouble code scanner uses this. Even if the check engine light is not on, trouble codes will be saved in the ECU.
Insert the jumper and then start the engine. The check engine light indicator will start blinking, and the fault code(s) will follow. Start keeping track of the flashes. As a guide, use Trouble Code 23. Example: Trouble Code 23 is represented by 2 lengthy flashes followed by 3 small flashes. There will be a considerable wait between trouble codes if there are multiple issue codes.
How can I read my OBD1 code if I don’t have a scanner?
Without a diagnostic instrument, we read by cutting the circuit between pins A and B. The vehicle will then enter diagnostic mode and flash the “check engine Light” numerous times. To get the diagnostic codes, we should count the flashes.
interpreting OBD1 codes:
- When performing any electrical operation that necessitates the ignition being on, you should always attach a car battery charger to your vehicle. Low voltage can be very problematic when troubleshooting and result in a lot of error messages that we don’t want.
- Connect PIN A and PIN B with a jumper wire.
- Turn the ignition to the ON position and leave the jumper wire in place. Never start the car.
- A flashing check engine light will appear. The number of flashes. If you have numerous issue codes, there will be less time between the digits of the difficulty codes and a longer wait between the codes. Code 16 is represented by the formula 1 flash * pause * 6 flashes.
- It will flash the code 121 flash * Pause * 2 flashes when all fault codes have been produced.
- Check the trouble code table lower down in the article and note down all the trouble code numbers you received.