Registered
I’m not sure what kind of jack you have, but I don’t think my trolley jack would be able to lift the cross part up and reach the center of it.
Where the lift pads are in the pictures, I’d simply jack it up on the sills. Jack up one side, position your axel stand underneath, then let go, moving the jack to the other side and repeating the same there.
In This Article...
Lift and support points for the Hyundai Sonata
* The dimensions shown in this picture correspond to actual measurements. [Millimeter (inch)]
You must consistently maintain your vehicle for optimal maintenance, safety, and maximum fuel efficiency.
impactsocket
Like the 2016 Hyundai Sonata, the 2011 Hyundai Sonata lacks a designated space to mount a jack.
a video showing how to lift the back of a 2011 Hyundai Sonata
The video’s creator, Richard Lloyd, has the following to say regarding jacking up the car:
I’m utilizing the rubber pad in the center of my jack to secure a nut and bolt to the center of the rear lower suspension swing arms. Rubber covers are also on the jack stands. You can see this in the video at 2:22. I placed these on the lower swing arms between the wheel and the jack. I also carried out the identical procedure on the front, but I did not utilize jack stands there. I dislike jacking the car up using the rocker panel pinch points since it causes corrosion and spoils the paint.
Where should the jack be installed on a Hyundai Tucson?
Under the baggage box cover, in the luggage compartment, are the jack, jack handle, and wheel lug nut wrench. The jack is solely available for changing emergency tires.
Where can a 2017 Hyundai Sonata be raised?
They are situated directly behind the front wheels and just in front of the back wheels, underneath the rocker panels of the vehicle. Our Car and Driver technician is demonstrating how to jack up the right front of the Hyundai Sonata car in the video up top.
How do you use a floor jack to jack up a car?
Now is the moment to begin lifting your car if you have figured out the jack positions. It is important to stop and replace your jack if it feels shaky at any stage during this procedure rather than risk damaging your car or yourself.
Put the floor jack underneath the jack point of the car. The saddle of the jack should make as much even contact with the frame of the vehicle as feasible.
With the handle, start pumping the floor jack. Pump away until the saddle of the jack touches the frame of the car. Take a break, determine how the saddle is situated with respect to the car’s frame and the jack points, and then restart if necessary. If not, keep pushing until your car is at a working height.
How much should my automobile be jacked up?
A jack lift height of 20 inches is sufficient for the majority of autos. Unless, of course, you like lifted off-road vehicles with enormous tires, in which case you’ll need something with a bigger lifting capacity.
Where do you jack up a car’s front end?
Consult a service handbook to find the suggested lift points and support locations for your particular vehicle before learning how to jack up your truck properly. Repair guides are typically offered online or at auto parts retailers.
- Engage the parking brake and block the back wheels before you start the jacking procedure to stop unwanted movement.
- You should begin lifting the car up from the front. Trucks with four-wheel drive can have their front ends elevated by setting the jack under the differential.
- A helpful hint is to position the jack for two-wheel-drive trucks underneath the engine’s jacking pad.
How should a scissor jack be applied to a car?
The scissor jack and a spare wheel are often located in the boot of your car. It is the smallest and least expensive option offered, and it has a handle to wind the arms apart, which raises the car.
The automobile will be raised off the ground after you place it underneath the jacking point and wind it clockwise. It only takes turning the handle the other way to lower it back down.
Can a car be left jacked up?
After employing a hydraulic lift or jack lift, a heavy object can be supported by a jack stand. In order to replace a wheel, change the oil, or inspect any other component underneath a car while working on it, you would use a jack stand. We have enquired as to the maximum amount of time a car can be supported by jack stands. Here is what they gave us.
A car can be left on jack stands for however long is necessary. For days, weeks, months, or even years, your car could be left on jack stands. As long as your car is jacked on a flat surface, everything will be OK. One thing to keep in mind is that it’s preferable to put your car on concrete rather than asphalt because asphalt is softer and your jack stands risk leaving a mark if left there for an extended period of time.
Since your tires will gradually lose air if you leave your car standing on its own and you run the risk of damaging your rim, leaving it on jack stands is a smart way to store your automobile. Additionally, check the vehicle’s security to ensure that even a small bump won’t cause it to overturn. Continue reading for more details about jack stands.
Let us first state that we hope you find the links provided here beneficial before you continue reading. We may receive a commission if you buy something after clicking on one of the links on this page, so thank you!
How are the front wheels jacked up?
Under the jack point that is placed close to the front tire, place a jack stand. Downshift the automobile. On the opposite side, repeat. At this point, you have the front wheels both raised (on jack stands) and the back wheels flat on the ground.
Why is my floor jack not functioning?
Our floor jack might not function if the recommended oil level is higher or lower. This reduces the capacity of your jack as well. You should remove the floor jack’s fill plug so that you may inspect the oil chamber within.
The suggested level for the majority of floor jacks is between 3/16 and 1/4 over the reservoir. If you need to replenish, make sure you start with the highest caliber oil. However, you would need to drain the extra oil if the jack’s oil level was greater than what was advised.
Additionally, you should be sure to regularly inspect the hydraulic jack to look for any dirt or debris in the oil chamber. You might also think about disassembling the floor jack to look for any broken components that could cause leaks within or externally. Consult a specialist if necessary.
Should lug nuts be loosened before jacking up the car?
- security first. Maintain a safe distance from oncoming traffic, put your car in park, engage the parking brake, and turn on your warning lights. It is preferable to ask for roadside help if you are unsure that you can avoid danger.
- Consult the owner’s manual. It should have directions for changing tires, including where the jacking point is.
- Bring out your spares and tools. Typically, they are kept in a compartment in the trunk. The jack should provide usage instructions as well.
- Make sure the jack is set up correctly. Ensure it is positioned correctly in the vehicle’s jacking point and is facing the right direction.
- Before jacking, loosen lug nuts by roughly a quarter turn.
- The car should be jacked up high enough so that the tire is off the ground.
- The lug nuts should be taken off and placed so they won’t roll away.
- Pull the flat tire off and place it behind the jack underneath your car, or if it’s too broad, try another position under the car. This is crucial in the event that the car slips off the jack.
- Make sure the valve stem is facing you as you install the spare.
- Hand-tighten the lug nuts while reinstalling them.
- Once the tire is in touch with the ground and partially loaded, lower the jack.
- To ensure that the wheel is properly installed, tighten the lug nuts in a star pattern rather than a circle pattern. This ensures that the wheel is not out of alignment and won’t pop back into place while you are driving, perhaps loosening other bolts and causing wobbling or even worse—the nuts breaking and the wheel coming off.
- The car should now be lowered all the way. You’re prepared to make a cautious trip to the nearest tire shop to get your regular tire changed or repaired.
Spares should only be driven for brief distances and at low speeds. Your spare tire’s speed rating can be lower than that of your primary tires. Have a tire specialist inspect your spare at the shop so that it is in working order for the next time you need it.