- Put the ignition on with your key. Turn the key to the first position.
- On the dashboard, press the reset trip meter button. Hold it down for a few seconds.
- Hold the odometer button down for around five seconds.
- Release the odometer button after it is off.
In This Article...
How can the maintenance needed light on a 2015 Toyota RAV4 be reset?
How to Turn Off the Maintenance Light on a RAV4
- Put your key in the ignition of the RAV4.
- On the dashboard, press and hold the trip meter reset button.
- For ten seconds, keep pressing the odometer button.
- Release the odometer button after the light is off, then start the vehicle.
How can you turn a Toyota Rav4’s maintenance light back on?
You should switch off the service light if it’s still on after your RAV4 has gotten maintenance. How to reset a maintenance light is as follows:
- Put the ignition on with your key. Turn the key to the first position. This is the position right before the automobile starts.
- On the dashboard, press the reset trip meter button. Hold it down for a couple of seconds. Next, turn your key to the second position.
- Hold the odometer button down for another five or so seconds. The light ought to beep, flash, and then shut off.
- Release the odometer button after it is off. your vehicle off. If the maintenance light on the Toyota RAV4 is still on, only carry out this procedure one or two more times to turn it off.
Get your RAV4 serviced if your maintenance light is still on. Follow your owner’s handbook to learn more about the suggested maintenance schedule for your RAV4 configuration. Maintenance lights can indicate a significant issue.
How can you turn a Toyota RAV4’s oil light back on?
In order to start the car, turn the ignition to position one with your key in the ignition. Turn the key to position two while pressing and holding the trip meter reset button on the dashboard. For 10 seconds, keep your finger on the odometer button. Then the light should flash, beep, and finally turn off.
How can the maintenance needed light on a Toyota push start be turned off?
Turn the key to position two while pressing and holding the odometer button on the dashboard. When the maintenance light begins to flash, keep holding the odometer button. There may even be beeping sounds. The light ought to dim.
How can you turn a Toyota’s maintenance needed light back on?
In order to start the car, turn the ignition to position one after inserting your key. Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off.
Why does my Rav4 indicate that maintenance is needed?
The significance of the emblem MAINT REQD is significant. The MAINT REQD light indicates when the vehicle’s scheduled maintenance is due when it illuminates. If your car is under two years old, this service can be covered by your ToyotaCare plan.
Why does my maintenance light come on after I change the oil?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to push it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.
Why does my Toyota state it needs maintenance?
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- If the car is on, turn it off.
- Now the light will read “MAINT REQD.”
- The ODO display will briefly flash before beginning to display only zeros.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- Press and hold the ODO reset / readout button while the engine is off.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
How should I respond if my maintenance light illuminates?
How Can the Maintenance Required Light Be Reset?
- Turn on your car. Look at your dashboard when your key is in the on position.
- Press the Trip Meter Reset Button after turning off the engine.
- Re-start the vehicle.
- Keep pressing the reset button.
- Reset button released
On a 2014 Toyota Tundra, how do you turn the maintenance light back on?
- Without starting the engine, turn the ignition to the “On position. If your car has a push-button ignition, press “Start” without depressing the brake pedal.
- By pushing the display change button or “Trip button,” you can change the display to “Trip A.”
- Completely shut off the car.
- Keep holding down the “Trip button.”
- Hold the “Trip button down while turning the ignition to “On without starting the car.
- Release the “Trip button” whenever the trip meter reads “all zeros.”